膨脹高溫計 的英文怎麼說
中文拼音 [péngzhànggāowēnjì]
膨脹高溫計
英文
expansion pyrometer- 膨 : 動詞(物體的長度或體積增加) expand; swell
- 脹 : 動詞1. (膨脹) expand; dilate; inflate 2. (脹大) swell; distend; bloat
- 高 : Ⅰ形容詞1 (從下向上距離大; 離地面遠) tall; high 2 (在一般標準或平均程度之上; 等級在上的) above...
- 溫 : Ⅰ形容詞(不冷不熱) warm; lukewarm; hot; gentle; mild Ⅱ名詞1 (溫度) temperature 2 (瘟) acute ...
- 計 : Ⅰ動詞1 (計算) count; compute; calculate; number 2 (設想; 打算) plan; plot Ⅱ名詞1 (測量或計算...
- 膨脹 : expand; swell; dilate; inflate; puff; bulge; inflation; expansion; dilatation; buckling; swelling...
- 高溫 : high temperature; elevated temperature; hyperthermia; megatemperature; inferno
-
And due to the heat expansile coefficient of the stainless steel rather high, the connecting force between the stainless steel pipe and the pipe coupling in the room temperature is much less than that between the titanium alloy pipe and the pipe coupling. the results accord with the tensile experiments well. finally, the dependence of dimensions of the coupling on the strength of the connector system is analyzed
模型計算還表明,被接管材料和管接頭材料之間的熱膨脹系數的差異會造成管接頭系統的室溫強度低於高溫強度;由於不銹鋼的熱膨脹系數較大,使得室溫下1不銹鋼管與n立tinb形狀記憶合金管接頭間的抱緊力遠小於鈦合金管與nitinb形狀記憶合金管接頭間的抱緊力,成功地解釋了拉脫實驗中的結果。Comparison of the calculated elastic moduli with the experiment ones for fcc al and bcc li and na it shows they are in perfect agreement with each other
當晶體從絕對零度升高到某一有限溫度下時,晶體發生體積膨脹,計算出發生體積膨脹后的新體積。The equipment for simultaneously measuring resistance, volume expansion and temperature was constructed. two different polymer matrices, crystalline high density polyethylene ( hdpe ) and amorphous polystyrene ( ps ) were selected, which were loaded with carbon black ( cb )
自行設計製作電阻-體積膨脹-溫度同步測量裝置,研究了炭黑( cb )填充聚合物基ptc材料的電阻率隨體積膨脹的變化關系,聚合物基體分別為結晶聚合物高密度聚乙烯( hdpe )和非晶聚合物聚苯乙烯( ps ) 。The thermal stress of ceramic regenerator resulting from its temperature difference and restricted extension and contraction has been calculated and analyzed, the result provides a theoretical basis for design and operation of high temperature air combustion system
對于由溫度分佈不均勻,陶瓷蓄熱體膨脹或收縮受限制而產生的熱應力進行了計算和分析,其結果為蓄熱式高風溫燃燒系統的設計及運行參數的選擇提供了理論依據。5. schapery model can be used to calculate the cte of composite when temperature is lower ( 50 - 100c ) and kerner model can be used when temperature is higher ( 300 - 450c ). the cte of composite will increased more quickly than that by three models when temperature is between ( 100 - 300c )
復合材料的熱膨脹系數在溫度較低( 50 100 )時可用schapery模型計算,在高溫( 300 450 )時可用kerner模型計算,在100 300之間則隨溫度升高增加的很快,且與所有模型分析結果不一致。Expansion thermometers are ideal problem solvers for difficult installation situations and demanding environments
膨脹式溫度計是解決安裝困難和高要求環境的理想方案。分享友人