自動推進裝置 的英文怎麼說

中文拼音 [zìdòngtuījìnzhuāngzhì]
自動推進裝置 英文
automatic feed unit
  • 自 : Ⅰ代詞（自己） self; oneself; one s own Ⅱ副詞（自然;當然） certainly; of course; naturally; willin...
  • 推 : 動詞1 （向外用力使物體移動） push; shove 2 （磨或碾） turn a mill or grindstone; grind 3 （剪或削...
  • 進 : 進構詞成分。
  • 裝 : Ⅰ名詞1 （服裝） dress; outfit; attire; clothing 2 （演員的化裝品） stage makeup and costume Ⅱ動詞...
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 自動 : 1 （自己主動） voluntarily; of one s own accord 2 （不憑借人為的力量） automatic; spontaneous 3 ...
  • 推進 : 1 （推動工作 使前進） push on; carry forward; advance; give impetus to 2 [軍事] move forward; dri...
  • 裝置 : 1 （機器設備的配件）installation; device; apparatus; equipment; arrangement; gear; appliance; rig...
  1. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  2. This text completely and systematically studies the status and the development of the pyrolysis and the fluidization of biomass, which distill the bio - oil in the domestic and international area, as well as the existing problems. this thesis primarily include following aspects : ( l ), by experimenting and measuring the energy ( heat value ) and the content of c, h, n chemical element of right 20 kinds of common biomass, on the base of the experimental result, and respectively established the biomass energy predict experiment formula with the element of h and c is from change, and passed the ro. os examination, which provides the basis and convenience for flash pyrolysis fluidization device energy to convert the rate to compute with biomass energy utilization calculation ; ( 2 ), proceeded the tg and dtg experimentation equal velocity ( 10 ? / min, 20 ? / min, 40 ? / min, 60 ? / min ) heating and constant temperature heating by studying on eight kinds of biomass samples, according to the experimental data and arrhenius formula, we established the dynamics model of pyrolysis of, then, using the goast - redfern and p function, we also solved the dynamics parameters and analyze out every kind of biomass ' s frequency factor and parameters of activation energy, and established the every kind of dynamics model of pyrolysis of biomass, all of these provide the theories and basis to make sure the reactor ' s flash pyrolysis work temperature scope design and the describing of pyrolysis reactor dynamics ; ( 3 ), in order to study and ascertain the process of heat completely getting to pyrolysis time of varied size biomass particles, we observed and measured the ratio of length and diameter ( l / d ) with the varied biomass through electron microscope, we concluded the l / d ratios usually is from 5. 0 to 6. 0, the average is 5. 3 ; ( 4 ), we studied the process of biomass transiting and the theory of complete pyrolysis time with the theory of complicated heat field, we got the time ( t ) of the varied size biomass particles arriving to complete pyrolysis, and we knew that the complete pyrolysis time and the time which get to the biggest production ratio are identical, all of these studies provide the theory base for design and forecasting the flash pyrolysis reactor solid state resort time ; ( 5 ), according to the above experiment result, synthesize to make use of the engineering the mechanics, engineering the material, machine the design to learn the principle, deduce, establish the theory of rotation cone flash pyrolysis reactor material resort time ( t ) and reasonable rotation velocity ( or frequency ) relation theory ; and ( 6 ), we gave the reactor ' s smallest cone angle certain, reactor cone wall strength design theory, the reactor production ability theory, the power design method and the critical rotation velocity theory

    本文較全面、系統地綜述了國內外生物質熱解液化制取生物燃油技術研究發展現狀及存在的問題，主要研究內容有： （ 1 ）實驗、測定了20種常見生物質的能量（發熱量）和c 、 h 、 n元素含量，根據實驗結果分別建立了以h和c為自變量的生物質能量預測經驗公式，並通過r _ （ 0 . 05 ）檢驗；為閃速熱解液化裝置能量轉化率計算和生物質能量利用率計算提供了依據和方便； （ 2 ）選擇了8種生物質試樣作了等加熱速率（ 10 min 、 20 min 、 40 min 、 60 min ）和恆溫加熱的tg和dtg實驗，根據實驗數據和阿倫尼烏斯公式建立了生物質熱解反應動力學微分方程，並採用goast - redfem積分法和p函數對其動力學參數進行了求解，解析出各種生物質的頻率因子和活化能參數，進而建立了各種生物質的熱解動力學模型，為科學確定反應器的閃速熱解工作溫度范圍及熱解反應動力學描述，提供了理論和依據； （ 3 ）為研究和確定不同尺度的生物質顆粒中心達到全熱解的時間，在體視顯微鏡下對不同粒度的生物質顆粒的長徑比進行了實驗觀察和測定，得出生物質的長徑比（ l d ）一般在5 . 0 6 . 0之間，平均為5 . 3的結果； （ 4 ）採用復雜溫度場傳熱學理論對生物質傳熱過程及充分熱解時間理論進行了研究，解析推導出了不同尺寸生物質顆粒中心溫度達到充分熱解溫度的時間（ t ） ，得出了理論推導的充分熱解時間與最大產油率的熱解時間相一致的結果，為閃速熱解反應器固相滯留時間設計和預測提供了理論依據； （ 5 ）根據上述實驗結果，綜合運用工程力學、工程材料、機械設計學原理，推導、建立了轉錐式閃速熱解反應器物料滯留時間（ ）與轉速（或頻率）合理匹配理論； （ 6 ）提出了轉錐式閃速熱解反應器的最小錐角設計、錐壁強度設計、生產能力設計理論和功率計算方法及臨界轉速理論等。
  3. Data inputting and graphinputting module respectively achieve data inputting of first system and electric firstwiring diagram inputting ; secondary scheme design module realizes scheme design ofsecondary loops including control, protection, signal, measure, automotive equipment, operation electrical source and electrical source for substation and power distributionstation, using rule - cased reasoning of expert system ; protective relaying settingcalculation module realizes setting calculation for first equipments which aretransformers, circuitries, capacitors, and electromotors ; secondary equipmentselection module realizes type selection of secondary microcomputer integratedequipments ; graph making out module realizes secondary drawings making outautomatically representing design production using case - cased reasoning of expertsystem and the drawings can be edited and modified under the secondary developedautocad environment

    數據輸入和圖形輸入模塊分別完成一次系統資料錄入和電氣主接線圖的輸入;二次方案設計模塊利用專家系統基於規則的推理實現變配電所各二次迴路的方案設計，包括控制、保護、信號、測量、自動裝置、操作電源和所用電源;繼電保護整定計算模塊實現主設備的整定計算，包括變壓器、線路、電容器和電動機;二次設備選型模塊實現二次微機成套裝置的型號選擇;圖形生成模塊利用專家系統基於實例的推理實現代表設計成果的各類二次圖紙的自動生成，生成的圖紙可以在二次開發的autocad環境下進行編輯和修改。
  4. Our systems were introduced as the only automatic water treatment equipments to users by the national mechanic industry motivity technical information website, which are organized by 86 institutes

    水處理裝置進入中國市場多年來，受到了用戶及有關專家的廣泛贊譽，由86個大型設計院及企業組成的全國機械工業動力科技信息網，將其作為向設計單位推薦的唯一全自動水處理裝置
  5. Subject to further studies to be carried out by relevant departments and institutions and if the results are satisfactory, we may consider means to encourage the voluntary installation of a safety device to openable aluminium windows with a view to enhancing window safety, possibly together with appropriate measures to motivate such installation

    視乎有關部門及學院的進一步研究結果，若結論令人滿意的話，我們會考慮如何鼓勵?民自願地為可開關鋁窗加裝安全裝置，以增強窗戶安全，並可能會透過適當的措施，推動?民安裝這等裝置。
  6. The research group of super ? critical fluid technology will apply the whole technology of extraction and separation, including technical parameters, analytical method of products, design and manufacture of equipment and automatic controlling system

    山東大學超臨界流體技術研究所，從制約超臨界流體技術推廣應用的關鍵問題入手，進行成套技術開發，包括萃取分離工藝、分析檢測方法、萃取設備設計製造和裝置的自動控制等。
分享友人
分享到 Line

分享到臉書