荷載控制 的英文怎麼說

中文拼音 [hézǎikòngzhì]
荷載控制 英文
load control
  • 荷 : 荷名詞（蓮） lotus
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  1. Engine load simulated control system was consisted of two unattached parts of work resistance simulated control subsystem and electric bow wave dynamometer control subsystem. with the mathematic models of engine load simulation controller, which transferred the work resistance ' s change to engine load change immediately, the system can met the need of the simulation control system

    發動機負荷模擬加載控制系統包括彼此獨立的作業阻力模擬控制子系統和電渦流測功機控制子系統兩部分，應用發動機負荷模擬控制器數學模型，使作業阻力的變化及時轉換為發動機負荷的變化，能夠滿足模擬系統的控制要求。
  2. Probe into bulldozer ' s ultimate load control system

    推土機極限載荷控制系統的探討
  3. Because these wind loads are a major structural consideration, they greatly influence the design of the flight control system.

    因為這些風載荷是結構上主要的考慮因素，它們很大地影響著飛行控制系統的設計。
  4. Flying boat is a controllable aircraft that can flying in the air, the flotage provided by the helum - filled bag inside the flying boat can support the boat and it s load in the air, motor pushing it forward ; the direction is guided by the device on it s tail, going down of the boat is made by escaping the gas inside, it can rise or fall straightly or stay in the air, no necessity of special site for taking off

    飛艇是一種可操縱的浮於空中的飛行器。在飛行中主要依靠內部充滿氦氣的氣囊提供的浮力，將飛艇及其載荷支持在空中，發動機為其提供前進的動力，通過操縱尾翼上的升降舵和方向舵控制飛艇的俯仰和方向運動，飛艇的下降是通過排放氣來實現的。飛艇可以垂直起降空中懸停，不需要有專用設備的起降場。
  5. Since the preload and the friction moment of the geminate bearing are dominating factors affecting the performance of the navigation platform frame system, based on theoretical study on the control methods of bearing ' s preloads and frictional moment, the paper puts forward a method to control the preload of the twin bearings accurately. moreover, a multifunctional test apparatus of the navigation platform bearing is designed, and a lot of experiments of bearing ' s rigidity and friction moment and preload assessment are done

    考慮到成對軸承預載荷和摩擦力矩是影響導航平臺框架系統性能的主要因素，本論文對成對軸承預載荷及摩擦力矩控制技術進行了理論研究，提出了一種精確控製成對軸承預載荷的配對方法，設計了導航平臺軸承多功能測試儀，並對導航平臺軸承的剛度、摩擦力矩和預載荷評定技術進行了試驗研究。
  6. Also, loads and control forces imposed by space vehicle guidance systems are generally small.

    此外，由空間飛行器導引系統所產生的載荷與控制力一般是很小的。
  7. The space shuttle undertook a topsecret mission with a military payload under pentagon control.

    航天飛機執行一項絕密使命，所使軍用載荷由五角大樓控制。
  8. It also has important reference value for the similar construction. by the safety and seismic evaluation of this aqueduct bridge, it has shown that ( 1 ) besides the structure of this aqueduct bridge was basically unharmed without some flake of concrete cover and revealing stirrup, its intensity basically reached the need of primary design. ( 2 ) from the side of carrying capacity, rib arch could satisfy the needs under the action of wind and earthquake, but some individual frame crossbeams and most rib arch tie beams could n ' t satisfy the need

    通過對東滑峪渡槽進行安全性能和抗震性能評估后表明： （ 1 ）渡槽除肋拱頂面有保護層剝落、箍筋外露，結構基本完好，其強度基本達到西安理工大學工程碩士專業學位論文原設計的強度要求； （ 2 ）從承載力方面看，在風荷載、地震作用下，肋拱基本滿足要求，個別排架橫梁不滿足要求，肋拱連系梁普遍不滿足要求；計入水平橫槽向地震作用的工況為設計控制工況。
  9. Engine load simulated control system was consisted of two unattached parts of work resistance simulated control subsystem and electric eddycurrent dynamometer control subsystem

    發動機負荷模擬加載控制系統包括彼此獨立的作業阻力模擬控制子系統和電渦流測功機控制子系統兩部分。
  10. Problems appearing at work and tackling methods are both presented. recently, the research result has been applied to the helicopter airscrew harmony loading test. the results of harmony loading test show that it has high performance

    目前，論文的研究成果已經成功地應用在某型直升機旋翼載荷模擬加載試驗系統中，實際加載試驗表明，該加載控制系統能很好的完成加載試驗控制，保證系統的控制性能指標。
  11. The checking methods of prestressed concrete penstock during construction stage are suggested. the formula is proposed to calculate the maximum distance of two consecutive strands to be result in uniformly distribution of concrete prestressed along the penstock

    提出了相鄰環預應力筋束的最大間距計算公式，確定了以混凝土抗裂為目標進行預應力筋束分步張拉施工與荷載控制的方法。
  12. Members section of the steel truss are designed mainly according to vertical load, which earthquake load can not change. however, changes of members stress should be regarded, such as the steel truss members connecting shearwall

    鋼桁架轉換結構設計主要受豎向荷載控制，地震荷載不改變其主控荷載，但對地震荷載作用下鋼桁架構件受力的變化應予以重視，尤其是與豎向構件連接的鋼桁架兩端構件。
  13. Structural internal forces and deformation caused by seismic load are bigger than that caused by automotive load. seismic load controls the designing of large span and small " width - to - span " ratio of large span cfst arch bridge. the seismic resistance is bigger than that with considering combination of various directions, so seismic load combination of various directions should been taken into account during design of large span cfst arch bridge

    地震荷載所引起的內力和變形均大於車輛荷載引起的內力變形，對大跨、寬跨比小的鋼管混凝土拱橋來說，應以地震荷載控制內力和變形設計，考慮多方向地震荷載的組合后，所得的地震力更大，說明在計算地震力時，應該考慮多方向地震荷載的組合。
  14. The methods considering the elastoplasticity are the elastic - plastic hinge method and the pseudo load method. based on the need of non - linear analysis, researchers brought forward nonlinear calculation methods to control the iterative constringency, such as the load controlling method, the displacement controlling method, the arc length controlling method and the pseudo load method

    考慮彈塑性的分析方法有：彈性-塑性鉸法和虛擬荷載法根據非線性研究分析的需要，研究人員先後提出了：荷載控製法、位移控製法、弧長控製法和做功控製法等控制迭代收斂的非線性計算方法。
  15. This paper deals with the following three topics with regard to the control of multiple manipulators : 1. deprive the kinematics and dynamical equations of two manipulators with identical structure on the basis of geometry theory, one of which has two links, giving the inverse solution to the kinematics of the system which consists of the manipulators and the grasped object ; 2. by use of load - distributing, design a controller coordinating multiple redundant manipulators whose parameters are known

    基於微分幾何理論推導出兩個具有相同結構的二連桿機器人的運動學逆解及與物體所成系統的動力學方程； 2在假設由多個冗餘機器人與物體組成系統的動力學模型確知的前提下，利用負荷分配法，設計了一種不僅能使關節力矩優化且能按照一定比例分配負荷的控制器，解決了以往控制器的一些缺陷，即忽視各個機器人的實際承載力，導致一些負荷力小的機器人卻必須承擔較大的負載，最終損壞機器人； 3
  16. It is important to soft developing. the topic of the paper has been listed in the basic research project for national defence of the " tenth - five project " by the commission of science technology and industry for national defence. one is " distribution experimentation and test technology ", the other is " mathematic helicopter and test technology ". base on the research of literature of the world, we will research the technology of measurement and control system

    本文結合十五國防預研項目「分散式協同綜合虛擬試驗與測試技術」和個五航空預研項目「直升機飛行載荷全數字加載控制和數據採集技術」的研究，在分析了國內外研究現狀和技術發展趨勢的基礎上，對其共性的關鍵技術之一? ?系統開發支持平臺（通用測控平臺）技術展開了深入研究。
  17. The load control system has already passed the test ' s validate. it shows that the design of whole system is correct. the system can truly simulate the real air - stream and put it on missile ' s wings to make them work on the same force situation as in the real spread process, so the relationship of explosive stuff and attack angle can be confirmed

    本文所設計的加載控制系統已通過實際系統的驗證，說明整個系統的設計是合理正確的，它能夠真實地模擬類似真實氣流阻力的載荷，並施加於彈翼或尾翼，模擬其在真實工作環境下的受力狀態，可以測算導彈攻角與火工品填藥量的關系。
  18. The ultimate load was controlled by the load on the middle of slabs when the slab thickness was more than approximately 43 cm

    板厚超過43cm時，極限荷載以板中加載控制為主。
  19. In this paper, the study was based on the emulational experience system of the tractor - implement. the emulational control system was composed of three parts : master pc monitor system, transmission and throttle control subsystem, engine load simulated control subsystem. using the system, many studies and experiments could be carried out on the implement units

    本文的研究是在拖拉機作業機組模擬試驗系統平臺上進行，模擬系統的控制系統由上位機監控系統、發動機及換擋控制系統、發動機負荷模擬加載控制系統等三大部分組成，利用本控制系統能對機組進行各種加載試驗研究。
  20. For the convenience of study, a simulation control system of tractor - implement combination was designed, which had the characteristics of reasonable structure, simple and practical. the control system was composed of three parts : master pc monitor system, transmission and throttle control subsystem, engine load simulated control subsystem. using the system could take many studies on implement units

    為研究方便，本文首先設計了結構合理，簡單實用的拖拉機作業機組模擬試驗控制系統，控制系統由上位機監控系統、發動機及換擋控制系統、發動機負荷模擬加載控制系統等三大部分組成，利用本控制系統能對機組進行各種加載試驗研究。
分享友人
分享到 Line

分享到臉書