著火溫度試驗 的英文怎麼說
中文拼音 [zhāohuǒwēndùshìyàn]
著火溫度試驗
英文
fire test- 著 : 著助詞1. (表示動作的持續) 2. (表示狀態的持續) 3. (用在動詞或表示程度的形容詞後面, 加強命令或囑咐的語氣) 4. (加在某些動詞後面, 使變成介詞)
- 火 : fire
- 溫 : Ⅰ形容詞(不冷不熱) warm; lukewarm; hot; gentle; mild Ⅱ名詞1 (溫度) temperature 2 (瘟) acute ...
- 度 : 度動詞[書面語] (推測; 估計) surmise; estimate
- 試 : 名詞(古代占卜用的器具) astrolabe
- 驗 : 動詞1. (察看; 查考) examine; check; test 2. (產生預期的效果) prove effective; produce the expected result
- 著火 : inflame; kindle; catch fire; blowing; be on fire
- 溫度 : [物理學] temperature
- 試驗 : trial; experiment; test
-
Test results show that the ignition process of pc in ignition chamber includes three stages. the effects of velocity, pc concentration and wall temperature on the ignition of pc are studied
試驗結果證實煤粉氣流在感應加熱點火室內的著火過程分為三個階段,揭示了煤粉入口速度、煤粉濃度、點火室壁面溫度對煤粉氣流著火的影響規律。Electrical apparatus for explosive gas atmospheres - part 4 : method of test for ignition temperature ; amendment 1
防爆電氣設備.第4部分:著火溫度試驗方法.修改件1This paper researched rules of ignition and combustion stability under pressurized environment, discussed how to calculate ignition temperature, and also studied the effects of many factors, such as categories of semi - coke, total pressure, oxygen concentration, particle size, heating rate, on ignition character
研究了加壓條件下半焦的著火規律和燃燒穩定性。討論了著火溫度的確定方法,對加壓下影響半焦著火特性的各種因素,如半焦種類、總壓、氧濃度、粒徑、加熱速率等進行了試驗研究。The difference among the elasticity modulus of various microstructures is probably the main reason, which caused the experiment results above. under the same experiment conditions, such as sample shape, size, surface roughness, establishment of testing system, pressure on the probe, and thickness of coupling medium, the variety of relative attenuation coefficient ( or ) in different heat treatment samples is measured and compared by measuring the attenuation obtained from the cylindrical surface of column. the result is as following : for 40cr and 38crmoal, a mt < az mq < a s < a p + f ; for gcrlssimn, a mt < a annea < s < a p + f ; and a increased with the increasing of frequency
在保證試樣形狀、尺寸、表面光潔度、系統參數設置、施加在探頭上的壓力以及耦合層厚度等測試條件一致的情況下,利用棒材圓柱面測衰減系數法,分別測定並比較上述不同熱處理試樣相對衰減系數的變化情況,得到的實驗結果是:對於40cr及38crmoal鋼, _ (低溫回火) (淬火) _ (高溫回火) _ (正火) ;對于gcr15simn鋼, _ (低溫回火) _ (退火) _ (高溫回火) _ (正火) ;且隨著頻率的提高,衰減系數均呈現增加的趨勢。The results show that, with the quenching temperature ( 270 ~ 380 ) increasing, the carbon content and percentage content of retained austenite increase first and then decrease, which are up to a maximum value at 360 ; the tensile strength of adi decreases ; the elongation and impact ductility of adi increase first and then decrease, which are up to a maximum value at 360 ; but the hardness of adi decreases first and then increases, which is up to a minimum value at 360
結果表明,在試驗溫度范圍內( 270 ~ 380 ) ,試樣中殘余奧氏體的含碳量及其含量隨著等溫淬火溫度的升高先增大后減小,均在360等溫淬火時出現最大值;抗拉強度隨著等溫淬火溫度的升高而逐漸降低;伸長率和沖擊韌度隨著等溫淬火溫度的升高先增大后減小,在360等溫淬火時出現最大值;硬度則隨著等溫淬火溫度的升高先減小后增大,當360溫淬火時硬度最低。分享友人