蒸發速率計 的英文怎麼說

中文拼音 [zhēngfāsùlǜjì]
蒸發速率計 英文
evaporation rate meter
  • 蒸 : Ⅰ動詞1. （蒸發） evaporate2. （利用水蒸氣的熱力使食物熟或熱） steam Ⅱ名詞[中醫] （將藥物隔水蒸熟） steaming
  • 發 : 名詞（頭發） hair
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 蒸發 : [物理學] [化學] evaporation; evaporate蒸發計 evaporometer; evaporimeter; atmidometer; atmometer; ...
  • 速率 : speed; rate; tempo
  1. More meaningful comparisons can be made by comparing water loss from the potometer with that from an atmometer ( an apparatus used to measure the rate of evaporation from a porous pot or other nonliving wet surface ), which allows uncontrolled evaporation

    更有意義的是，可以比較蒸騰計的失水與蒸發計（通過有孔小罐或者潮濕表面來測量蒸發速率的儀器）的失水間的區別。
  2. As to the simulation, three - dimensional n - s equations and two - phase flow model, in which the liquid toluene spray as discrete particles was considered, were employed to describe the turbulent combustion processes in the combustion chamber. the mass and energy transfer between the two phases were calculated by the droplet evaporation model, and the arrehnius model was used to obtain the gas chemical reaction rate. the details of 3d flow field, the distributions of temperature and compounds were obtained by solving the equations

    數值模擬方面，應用三維湍流n - s方程以及顆粒軌道模型描述了激光器燃燒室內部的噴霧兩相燃燒流動過程，兩相之間的質量、能量交換由液滴蒸發模型計算，氣相化學反應速率由arrhnius公式計算，通過耦合求解氣液兩相模型方程，模擬了燃燒室三維流場，得到了燃燒室內的溫度和組分濃度分佈。
  3. Test methods for evaporation rates of volatile liquids by shell thin - film evaporometer

    殼式薄膜蒸發計測定揮發性液體蒸發速率的試驗方法
  4. An instrument that measures the rate of water evaporation

    汽化計，蒸發計測定水蒸發速率的儀器
  5. Thermodynamic analysis on wet compression process is done in this thesis and studies are done on ideal wet compression process, actual wet compression process, water droplet evaporative rate, wet compression work, inlet evaporative cooling, wet compression efficiencies and water droplet breaking. and thermodynamic model of wet compression process is established, which gives out rules of and methods to calculate wet compression parameters

    本文從熱力學的角度對濕壓縮過程進行了分析，分別對理想濕壓縮過程、實際濕壓縮過程、水滴的蒸發速率、濕壓縮功、進氣蒸發冷卻、濕壓縮效率和水滴的破碎等進行了研究，建立了濕壓縮過程的熱力學模型，給出了濕壓縮過程狀態參數的變化規律和計算方法。
  6. Two typical examples analyses are conducted for the average conditions both of winter and summer climates under vapor diffusion and air leakage. a further discussion is set forth to determine the main factors that the moisture accumulation in wall is affected. it is found that the factors are the relative humidity at the wall surface, indoor temperature, permeability, air pressure difference and rate of the infiltrative or exfiltrative airflow

    本文首先研究了墻體內的濕氣遷移過程，詳細分析了濕積累現象形成的原因，通過對夏、冬兩季平均氣候下墻內溫度、水蒸氣壓力、相對濕度及濕積累在僅有擴散、擴散與空氣滲透同時存在等情況所作的具體計算，發現墻內、外表面的相對濕度、室內溫度、滲透率、空氣壓差以及空氣的滲流速度是影響墻內濕積累的主要因素。
分享友人
分享到 Line

分享到臉書