蝸傳動 的英文怎麼說

中文拼音 [zhuàndòng]
蝸傳動 英文
worm driving
  • 蝸 : 名詞[動物學] （蝸牛） snail
  • 傳 : 傳名詞1 （解釋經文的著作） commentaries on classics 2 （傳記） biography 3 （敘述歷史故事的作品）...
  1. Cased worm gear

    閉式蝸輪傳動
  2. Specification for worm gearing - metric units

    蝸輪傳動裝置規范.第2部分:米制單位
  3. The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters ， the cad system can make optimization design and strength check for the worm gear ， draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm ， judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point ， make project design and structure design for the reducer and draw its 2d parts and assembly

    研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統：包括幾何參數設計計算模塊，強度校核模塊，繪制齒面接觸線模塊，蝸桿齒厚變化曲線模塊和蝸桿根切判別模塊；開發了平面二次包絡環面蝸桿減速器外形與結構尺寸數據庫以及傳動效率數據庫，建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫；開發了平面二次包絡環面蝸桿減速器參數化建模軟體：包括零部件的參數化建模模塊和裝配圖的參數化建模模塊，其中零部件的參數化建模包括蝸桿軸系的參數化建模、蝸輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。
  4. Planar double - enveloping worm gearing terminology

    平面二次包絡環面蝸桿傳動術語
  5. Specification for worm gearing - imperial units

    蝸輪傳動裝置規范.第1部分:英制單位
  6. Planar double - enveloping worm gearing accuracy

    平面二次包絡環面蝸桿傳動精度
  7. Basic parameters of cylindrical worm gears

    圓柱蝸桿傳動基本參數
  8. D371x worm wheel butterfly balbe - changmao

    D371x型蝸輪傳動蝶閥- changmao
  9. D371x worm wheel butterfly vavle

    D371x型蝸輪傳動蝶閥
  10. D371x worm wheel butterfly balbe

    D371x型蝸輪傳動蝶閥
  11. Butterfly valves with gear actuator

    蝸輪傳動蝶閥
  12. Analyses on the length of contact lines and the contact area of a double enveloping wormgearing with planar generating surface

    平面二次包絡環面蝸桿傳動接觸狀況分析
  13. On the basis of the engage efficiency and lubricious conditions, theoretical transmission efficiency with the different drive ratios ( 1 / 50 and 6 / 31 ) of involute cylinder worm gears is analyzed. at the same time, the change trend of engage efficiency and transmission efficiency with different design parameters is discussed. the experimental investigation on transmission efficiency

    從漸開線蝸輪蝸桿傳動的嚙合效率和潤滑條件兩個方面對不同傳動比的漸開線圓柱蝸桿的傳動效率進行理論分析，並通過傳動比分別為1 / 50和6 / 31的漸開線圓柱蝸桿設計參數得到蝸桿潤滑條件的理論分析結果和蝸桿嚙合效率、傳動效率的變化趨勢，同時利用電測法對蝸桿傳動的傳動效率、潤滑油平衡溫度進行測試，將測試數據與理論計算結果進行對比分析，得出理論分析結果的正確性。
  14. On the condition of “ many - head ” and “ small drive ratio ” ， the plane double enveloping hourglass worm can not settle the problem of undercutting and sharpening simultaneously. it has devoted to a new type hourglass worm _ sphere double enveloping hourglass worm. the coordinate system is established according to the frock. the meshing equation and the tooth equation of worm and gear have been developed and the distribution of contact line on gear tooth is analyzed. to evaluate the meshing quality ， four meshing quality indexes and five original parameters are put forward. through mass programming computing ， the relations between meshing quality and original parameters are derived and depicted by graphs

    考慮到平面二次包絡環面蝸桿傳動在多頭小傳動比條件下根切與齒頂變尖的矛盾很難同時解決且嚙合性能較差，介紹了一種新型環面蝸桿傳動? ?球面二次包絡環面蝸桿傳動.在研究過程中，根據工裝建立了坐標系，根據一二包過程的運動關系推得了嚙合方程和蝸桿與蝸輪的齒面方程，分析了蝸輪齒面上的接觸線分佈.為了評價嚙合性能，提出了4項性能指標和5項原始參數，通過大量編程計算得到了嚙合性能指標與原始參數之間的關系，並以圖表直觀的表示
  15. Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3

    通過漸開線圓柱蝸桿、蝸輪的齒面方程式，利用ideas - 5 . 0軟體建立了傳動比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型，在此基礎上應用接觸有限元方法對該傳動進行了彈性接觸分析，包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況； 3
  16. Note : this table for the convention flange connection worm gear and worm drive metal hard seal fixed ball valve model establishment, the major parts material and the suitable operating mode, other requests and its model establishment sees the ball valve model establishment method

    注：本表為常規法蘭連接蝸輪蝸桿傳動金屬硬密封固定球閥的型號編制、主要零件材料及適用工況，其他要求及其型號編制見球閥型號編制方法。
  17. General purpose metallic hose clamps. worm drive type. specifications

    通用金屬的軟管卡箍.蝸桿傳動式.規范
  18. It is provided with worm - gear box regulation to have a more accurate depth of paper press. the blade part is driven by independent gear and adjusted by ratchet wrench. it is also equipped with ruler to shorten the time required for blade adjustment

    採用蝸輪箱調節，使壓線深度更加準確，刀頭部分使用單獨齒輪傳動，利用棘輪板手調動，並帶有長尺，使調刀時間縮短。
  19. The worm - drive is widely used in modern industry, especially the ordinary cylinder worm - drive in machine tool manufacturing sector. main disadvantages of worm dives are lubrication and wear problems due to relatively high sliding at the tooth contacts. the ordinary cylinder worm - drive has almost become an exclusive selection in general low speed transmission work - platform and continuous graduation mechanism

    蝸桿傳動具有傳動比大、體積小、運轉平穩、噪音小等特點，在現代工業中應用非常廣泛，在機床製造業中，普通圓柱蝸桿傳動的應用尤為普遍，並且幾乎成了一般低速傳動工作臺和連續分度機構的唯一傳動形式。
  20. Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance

    根據漸開線圓柱蝸桿傳動的創成方法，建立了漸開線圓柱蝸桿和蝸輪的接觸線方程式、齒面方程式，分析了漸開線圓柱蝸桿傳動的剛性嚙合特性，如蝸桿與蝸輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和蝸桿與蝸輪間相對速度方向和接觸線方向的夾角對傳動性能的影響； 2
分享友人
分享到 Line

分享到臉書