蝸形齒輪 的英文怎麼說
中文拼音 [xíngchǐlún]
蝸形齒輪
英文
scroll gear-
The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters ， the cad system can make optimization design and strength check for the worm gear ， draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm ， judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point ， make project design and structure design for the reducer and draw its 2d parts and assembly
研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統：包括幾何參數設計計算模塊，強度校核模塊，繪制齒面接觸線模塊，蝸桿齒厚變化曲線模塊和蝸桿根切判別模塊；開發了平面二次包絡環面蝸桿減速器外形與結構尺寸數據庫以及傳動效率數據庫，建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫；開發了平面二次包絡環面蝸桿減速器參數化建模軟體：包括零部件的參數化建模模塊和裝配圖的參數化建模模塊，其中零部件的參數化建模包括蝸桿軸系的參數化建模、蝸輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3
通過漸開線圓柱蝸桿、蝸輪的齒面方程式，利用ideas - 5 . 0軟體建立了傳動比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型，在此基礎上應用接觸有限元方法對該傳動進行了彈性接觸分析，包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況； 3The process has an advanced principle. the involute hourglass worm drive can realize the design machining of gear form and direction, and the internal meshing honing gear has high efficiency. this process has all merits mentioned above, and also has the advantages of quality stability, high productivity for rude and finish machining
該工藝原理先進，它集有利於實現齒形、齒向設計加工的漸開面環面蝸桿傳動與高效的內嚙合珩齒的優點與一體，對齒輪的粗、精加工都有質量穩定、生產效率高的優點。The software uses two entity configuration methods : extruding and simulating entity cutting in realizing three dimensional configuration, which successfully achieve three dimensional configuration of involute columnar vertical gear, involute columnar helical gear, standard vertical spline, archimedes worm and disco - cam
軟體在三維造型功能實現上使用了拉伸和模擬實體切削兩種實體造型方法，成功地實現了漸開線圓柱直齒輪、漸開線圓柱斜齒輪、標準直齒條、阿基米德蝸桿和盤形凸輪的三維造型。分享友人