蝸桿傳動 的英文怎麼說

中文拼音 [gǎnzhuàndòng]
蝸桿傳動 英文
worm drive
  • : 名詞[動物學] (蝸牛) snail
  • : 桿名詞(桿子) pole; staff
  • : 傳名詞1 (解釋經文的著作) commentaries on classics 2 (傳記) biography 3 (敘述歷史故事的作品)...
  1. The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters , the cad system can make optimization design and strength check for the worm gear , draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm , judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point , make project design and structure design for the reducer and draw its 2d parts and assembly

    研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統:包括幾何參數設計計算模塊,強度校核模塊,繪制齒面接觸線模塊,齒厚變化曲線模塊和根切判別模塊;開發了平面二次包絡環面減速器外形與結構尺寸數據庫以及效率數據庫,建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫;開發了平面二次包絡環面減速器參數化建模軟體:包括零部件的參數化建模模塊和裝配圖的參數化建模模塊,其中零部件的參數化建模包括軸系的參數化建模、輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。
  2. Planar double - enveloping worm gearing terminology

    平面二次包絡環面蝸桿傳動術語
  3. Planar double - enveloping worm gearing accuracy

    平面二次包絡環面蝸桿傳動精度
  4. Basic parameters of cylindrical worm gears

    圓柱蝸桿傳動基本參數
  5. Analyses on the length of contact lines and the contact area of a double enveloping wormgearing with planar generating surface

    平面二次包絡環面蝸桿傳動接觸狀況分析
  6. On the basis of the engage efficiency and lubricious conditions, theoretical transmission efficiency with the different drive ratios ( 1 / 50 and 6 / 31 ) of involute cylinder worm gears is analyzed. at the same time, the change trend of engage efficiency and transmission efficiency with different design parameters is discussed. the experimental investigation on transmission efficiency

    從漸開線蝸桿傳動的嚙合效率和潤滑條件兩個方面對不同比的漸開線圓柱效率進行理論分析,並通過比分別為1 / 50和6 / 31的漸開線圓柱設計參數得到潤滑條件的理論分析結果和嚙合效率、效率的變化趨勢,同時利用電測法對蝸桿傳動效率、潤滑油平衡溫度進行測試,將測試數據與理論計算結果進行對比分析,得出理論分析結果的正確性。
  7. On the condition of “ many - head ” and “ small drive ratio ” , the plane double enveloping hourglass worm can not settle the problem of undercutting and sharpening simultaneously. it has devoted to a new type hourglass worm _ sphere double enveloping hourglass worm. the coordinate system is established according to the frock. the meshing equation and the tooth equation of worm and gear have been developed and the distribution of contact line on gear tooth is analyzed. to evaluate the meshing quality , four meshing quality indexes and five original parameters are put forward. through mass programming computing , the relations between meshing quality and original parameters are derived and depicted by graphs

    考慮到平面二次包絡環面蝸桿傳動在多頭小比條件下根切與齒頂變尖的矛盾很難同時解決且嚙合性能較差,介紹了一種新型環面蝸桿傳動? ?球面二次包絡環面蝸桿傳動.在研究過程中,根據工裝建立了坐標系,根據一二包過程的運關系推得了嚙合方程和輪的齒面方程,分析了輪齒面上的接觸線分佈.為了評價嚙合性能,提出了4項性能指標和5項原始參數,通過大量編程計算得到了嚙合性能指標與原始參數之間的關系,並以圖表直觀的表示
  8. Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3

    通過漸開線圓柱輪的齒面方程式,利用ideas - 5 . 0軟體建立了比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型,在此基礎上應用接觸有限元方法對該進行了彈性接觸分析,包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況; 3
  9. Note : this table for the convention flange connection worm gear and worm drive metal hard seal fixed ball valve model establishment, the major parts material and the suitable operating mode, other requests and its model establishment sees the ball valve model establishment method

    注:本表為常規法蘭連接蝸桿傳動金屬硬密封固定球閥的型號編制、主要零件材料及適用工況,其他要求及其型號編制見球閥型號編制方法。
  10. General purpose metallic hose clamps. worm drive type. specifications

    通用金屬的軟管卡箍.蝸桿傳動式.規范
  11. The worm - drive is widely used in modern industry, especially the ordinary cylinder worm - drive in machine tool manufacturing sector. main disadvantages of worm dives are lubrication and wear problems due to relatively high sliding at the tooth contacts. the ordinary cylinder worm - drive has almost become an exclusive selection in general low speed transmission work - platform and continuous graduation mechanism

    蝸桿傳動具有比大、體積小、運轉平穩、噪音小等特點,在現代工業中應用非常廣泛,在機床製造業中,普通圓柱蝸桿傳動的應用尤為普遍,並且幾乎成了一般低速工作臺和連續分度機構的唯一形式。
  12. Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance

    根據漸開線圓柱蝸桿傳動的創成方法,建立了漸開線圓柱輪的接觸線方程式、齒面方程式,分析了漸開線圓柱蝸桿傳動的剛性嚙合特性,如輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和輪間相對速度方向和接觸線方向的夾角對性能的影響; 2
  13. The meshing efficiency of the drive is studied and analyzed in theory. the different formulas for meshing efficiency of drive are introduced on different conditions when stator or worm is fixed respectively

    從理論上研究分析了滾錐齒超環面行星蝸桿傳動的嚙合效率,推出了在定子固定和固定兩種情況下滾錐齒超環面行星蝸桿傳動嚙合效率的計算公式。
  14. It can be regard as the theoretical basis to optimize the drive. according to the gear meshing theory, the meshing equations, the contact line equations and tooth profile equations are given. it gives a base for 3d modeling the drive

    按照齒輪嚙合理論,推導出了滾錐齒超環面行星蝸桿傳動的接觸線方程、嚙合方程及各輪輪齒的齒面方程,為滾錐齒超環面行星蝸桿傳動的三維建模奠定了基礎。
  15. On the base of deducing meshing theory, by simplifying the parameters and using software, the 3d model of the rolling cone - type toroidal drive is given. and the parametric models are realized. the assemble chart of drive is given

    在嚙合理論推導的基礎上,通過對滾錐齒超環面行星蝸桿傳動的各參數進行簡化處理,利用計算機軟體對滾錐齒超環面行星蝸桿傳動進行了三維實體參數化建模,實現了模型的參數化,給出了該的裝配圖,並進行了態模擬。
  16. By means of the optimization method - punishing function method and taking the sum of the planet gear radius and center distance as the target function, the parameters of drive are optimized. by using the optimization program, the initial serial studies of drive are completed, the best serial parameter value of the drive is given

    採用外點罰函數優化方法,通過取行星輪半徑和中心距之和作為優化目標函數,對滾錐齒超環面行星蝸桿傳動進行了參數優化,運用此優化程序,初步完成了對該種的系列化研究,給出了系列的最佳參數取值。
  17. According to the high precision and rotation stability requirement of negative scan unit of cylinder photography typesetting machine, the three levels of cylindrical gears transmission separately, the two - stage cylindrical gears - worm drive, and the worm drive was chosen through calculating its velocity ratio, the checking transmission precision, carrying on the movement precision analysis to the sweep unit, and computing overall transmission error

    摘要針對圓筒型照相排版機底片掃描裝置要求精度高,轉平穩的特點,分別選擇三級圓柱齒輪,雙級圓柱齒輪蝸桿傳動蝸桿傳動3種常見的方式,計算其比,驗算精度,對掃描裝置進行運精度分析,計算總體誤差。
  18. The process has an advanced principle. the involute hourglass worm drive can realize the design machining of gear form and direction, and the internal meshing honing gear has high efficiency. this process has all merits mentioned above, and also has the advantages of quality stability, high productivity for rude and finish machining

    該工藝原理先進,它集有利於實現齒形、齒向設計加工的漸開面環面蝸桿傳動與高效的內嚙合珩齒的優點與一體,對齒輪的粗、精加工都有質量穩定、生產效率高的優點。
  19. The motion of the drive is also demonstrated. the paper mainly concludes the following works : the paper introduces the meshing theory of rolling cone - type toroidal drive and the motional relations of all parts, gives the formula of transmission radio. the relation between tooth numbers and helix angle of every parts is found out, and the assemble relation among all the parts is also given

    本論文主要包括以下內容:介紹了超環面行星蝸桿傳動原理及各構件間的運關系,分固定和定子固定兩種情況,給出了這種新型比計算公式,得出了各輪齒數與計算圓處螺旋升角間的關系和各構件間的裝配關系,從而為該的優化打下理論基礎。
  20. The keep with bounds were be fuzzy by the method of oblige line. this program not only has been used to optimization the pdew but also could used to control the fuzzy factor that could change the strength of fuzzy. when the fuzzy factor equal to one, the fuzzy optimization program could change to a general optimization program

    該優化設計程序不僅適應于平面二次包絡環面蝸桿傳動的模糊優化,而且可以改變模糊因子的大小,控制約束條件的模糊程度,甚至變換為常規的優化設計程序,程序的適用范圍較廣。
分享友人