蝸桿軸 的英文怎麼說

中文拼音 [gǎnzhóu]
蝸桿軸 英文
wirm wheel shafe
  • 蝸 : 名詞[動物學] （蝸牛） snail
  • 桿 : 桿名詞（桿子） pole; staff
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  1. Main products include suited offset point imprinter bearing sets comber gear for weaving industry metal mould and gear vacuum gear synchro gear worm worm wheel. acme whorl fitting and all kinds of fittings with various gears

    主要產品：印刷行業各種膠印機和印后設備輪及軸承套，紡織行業精梳機輪，金屬板材壓延模具和輪，真空泵輪同步帶輪蝸桿蝸輪副acme螺紋副各種直斜錐及各種盤類和軸類件等機械加工件。
  2. Analysis of the axial profile of an involute helicoid worm

    漸開線圓柱蝸桿軸向齒形分析
  3. The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters ， the cad system can make optimization design and strength check for the worm gear ， draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm ， judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point ， make project design and structure design for the reducer and draw its 2d parts and assembly

    研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統：包括幾何參數設計計算模塊，強度校核模塊，繪制齒面接觸線模塊，蝸桿齒厚變化曲線模塊和蝸桿根切判別模塊；開發了平面二次包絡環面蝸桿減速器外形與結構尺寸數據庫以及傳動效率數據庫，建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫；開發了平面二次包絡環面蝸桿減速器參數化建模軟體：包括零部件的參數化建模模塊和裝配圖的參數化建模模塊，其中零部件的參數化建模包括蝸桿軸系的參數化建模、蝸輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。
  4. For the dimensions of the double extention worm shafts, please consider the drawing of relevant nmrv size

    所有雙出軸蝸桿的尺寸，請參考nmrv的相關圖紙。
  5. The strength and fatigue analysis of spline shaft of hq1400 high pressure pump worm

    1400型壓裂泵蝸桿花鍵軸強度及壽命分析
  6. Cylindrical worms ; dimensions, correlation of shaft centre distances and gear ratios of worm gear drives

    圓柱形蝸桿.尺寸軸心距和蝸輪傳動傳動比之間的關系
  7. After considering the coupling of the mounting errors and elastic deformation, the meshing influences of the error of the center distance, the setting parametric error in the axial direction, and the intersect angle between the two axes on transmission performance are investigated. 4

    考慮到安裝誤差和載荷作用下的彈性變形等非共軛因素耦合作用，分析了漸開線蝸桿傳動在安裝時存在中心距誤差，軸間相對位置誤差，軸間相對夾角誤差對其承載嚙合的影響； 4
  8. This paper analyzes and discusses the problems involving the design of the electronic control ( ec ) and numerical control ( nc ) systems for a new type nc grinder - machine used to grind planar quadratic and annular enveloping worms based on novel four - axis - interpolation, in which a central fabricating method is introduced

    摘要本文作者設計了新型四聯動平面二次包絡蝸桿數控磨床的數控及電控系統，該磨床採用虛擬中心的方法，通過兩正交軸的圓插補及磨頭基座的自轉實現了傳統蝸桿加工磨床上的砂輪工作面的平面回轉運動，克服了傳統加工蝸桿工作層面多，結構復雜，加工精度、效率低等缺點。
  9. Calculation of load capacity of cylindrical worm gear pairs with shaft angle 90

    帶軸夾角90的圓筒形蝸桿副的承載能力的計算
  10. Set three electromagnets on a circle. so their suction can be loaded on the specimen through the arms of the bend moment. and then the bend moment is loaded on the specimen

    扭矩是通過蝸輪-蝸桿機構進行加載的，為了避免彎扭矩加載的互相干擾，文中選用了雙萬向聯軸器進行彎矩和扭矩的解耦，使二者的加載互相獨立，互不干擾。
分享友人
分享到 Line

分享到臉書