螺旋介面 的英文怎麼說

中文拼音 [luóxuánjièmiàn]
螺旋介面 英文
screw joint
  • 螺 : 1. [動物學] （軟體動物） spiral shell; snail; conch 2. （螺旋形的指紋） whorl （in fingerprint）
  • 旋 : 旋Ⅰ動詞1 （旋轉） whirl 2 （用車床切削或用刀子轉著圈地削） turn sth on a lathe; lathe; pare Ⅱ名詞...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 螺旋 : 1 （具有螺紋的圓柱體 屬于斜面類的簡單機械） corkscrewspin; screw; spiral; helix 2 （螺旋現象;尾旋...
  • 介面 : joggle; nozzle; mouthpiece; [計算機] interface
  1. The motion of the drive is also demonstrated. the paper mainly concludes the following works : the paper introduces the meshing theory of rolling cone - type toroidal drive and the motional relations of all parts, gives the formula of transmission radio. the relation between tooth numbers and helix angle of every parts is found out, and the assemble relation among all the parts is also given

    本論文主要包括以下內容：介紹了超環面行星蝸桿傳動的傳動原理及各構件間的運動關系，分蝸桿固定和定子固定兩種情況，給出了這種新型傳動的傳動比計算公式，得出了各輪齒數與計算圓處螺旋升角間的關系和各構件間的裝配關系，從而為該傳動的優化打下理論基礎。
  2. And then we introduce bezier, b - spline and non - polynomial curves and surfaces modeling, which include l - splines, helix splines, splines in tension and c - curves etc. by analyzing the characters of bezier curves and b - spline curves, we construct trigonometric polynomial curves in the space of trigonometric functions, which assume the characters of b zier curves and b - spline curves

    闡述了cagd中參數曲線曲面造型的發展歷史並介紹了bzier方法、 b樣條方法以及非多項式曲線曲面造型方法，後者包括l -樣條、螺旋樣條、張力樣條以及c -曲線等。文章以b zier曲線和b樣條曲線的特點為基礎，在三角函數空間中構造一組具有上述兩類曲線特性的三角函數多項式曲線，稱其為t - b zier曲線和t - b樣條曲線。
  3. In this dissertation, we have made one embedded family cleaning robot which is a collaborate project developed by hit ( harbin institute of technology university ) between hit and longchang company, guangdong province as the instance. we make a specific and roundly introduction about the specific development of embedded software for the cleaning robot. two important algorithms have been proposed, the internal spiral coverage algorithm based on grid - map and auto - docking and recharging algorithm

    本文以與廣東龍昌公司的合作開發項目的嵌入式家庭清掃機器人為例，全面而重點地介紹了針對實物機器人的嵌入式軟體開發，提出了基於柵格地圖表示方法的內螺旋覆蓋演算法和自主對接充電演算法，並對兩個演算法進行了全面深入的探討。
  4. The basic principal and general structure of dry gas seal are introduced briefly, and aiming at the characteristics of logarithm spiral curve, the calculation of the pressure to the spiral groove end surface by the theory of narrow groove are given. the method of narrow groove theory and finite element method are utilized to optimize the end surface structure of the spiral groove dry gas seal. the structure of the seal is confirmed on the base of the result

    簡要介紹了干氣密封的基本原理和一般結構，同時針對對數螺旋線形的特點，介紹了窄槽理論對螺旋槽端面的壓力分佈計算，利用窄槽理論和有限元方法對螺旋槽干氣密封端面結構進行了優化，並得出了優化結果，根據這一結果，確定了具體的密封結構。
  5. Additionally the display case may be rotated axial - wise by detaching the counter nut at the pressure connection

    另外，拆開壓力介面的埋頭螺母，顯示屏可以軸向旋轉。
  6. Laboratory glassware ; tightness test of conical joints, spherical joints and stopcocks

    實驗室玻璃儀器.球形介面和旋塞的螺旋連接的密封性檢
分享友人
分享到 Line

分享到臉書