螺旋小齒輪 的英文怎麼說
中文拼音 [luóxuánxiǎochǐlún]
螺旋小齒輪
英文
helical pinion- 螺 : 1. [動物學] (軟體動物) spiral shell; snail; conch 2. (螺旋形的指紋) whorl (in fingerprint)
- 旋 : 旋Ⅰ動詞1 (旋轉) whirl 2 (用車床切削或用刀子轉著圈地削) turn sth on a lathe; lathe; pare Ⅱ名詞...
- 小 : Ⅰ形容詞1 (體積、面積、數量、強度等不大) small; little; petty; minor 2 (年紀小的; 年幼的) youn...
- 齒 : Ⅰ名詞1 (牙; 牙齒) tooth 2 (物體上齒形的部分) a tooth like part of anything 3 [書面語] (年齡...
- 輪 : Ⅰ名1 (輪子) wheel 2 (像輪子的東西) wheel like object; ring; disc 3 (輪船) steamer; steamboa...
- 螺旋 : 1 (具有螺紋的圓柱體 屬于斜面類的簡單機械) corkscrewspin; screw; spiral; helix 2 (螺旋現象;尾旋...
- 齒輪 : gear [rack; toothed] wheel; (toothed) gear; wheel gear
-
Through systemic analyzing on spiral helical gear transmission with different basic parameters, the essay found out rules of how can such basic parameters influence spiral helical gear engagement characteristics. so it brings forward the auxiliary assembling mode of adopting one straight gear and one helical gear on condition of little axial angle as well as treasures to ameliorate ill engagement performance on condition of large axial angle, another two jobs of the essay are to clarify the wrong concept that spiral helical gear can only transmit movement but not impetus and to provide a brief and practical method of analyzing contact for gear pairs whose surface equations can be written out directly
通過對不同基本參數的螺旋齒輪傳動進行系統研究,找出了螺旋齒輪基本參數對其嚙合特性的影響規律,提出小軸交角條件下可採用一直齒輪、一斜齒輪的齒輪副組合方式,給出了大軸交角條件下嚙合性能不良的改進措施。澄清了螺旋齒輪只能傳遞運動不能傳遞動力的誤區,為能夠直接寫出齒面方程的齒輪副進行齒面接觸分析提供了一種簡便、實用的新方法。The changing carbon potential carburization - hot oil matrempering technology of helical bevel gear for automobile driven axle is introduced in this article. the board test and production application show that the technology not only quenchs directly gear after carbrization, but also decreases the heat treatment deformation and raises the contact fatigue life of gear
介紹了汽車驅動橋螺旋錐齒輪的變碳勢滲碳一熱油分級淬火工藝,臺架試驗及生產應用表明,該工藝與專用滲碳淬火掛具相結合,不僅可實現齒輪滲碳后直接淬火,而且熱處理變形小,齒輪接觸疲勞壽命也有所提高。Difference surface in combination with the least square method is employed for the evaluation of topographic deviation for sbg
將差曲面和最小二乘法相結合進行螺旋錐齒輪拓撲誤差評定。Normal section linear diagram of two gears " surfaces, which is on the arbitrary section, has also been protracted. the writing validated the correctness of the mathematical model and experimenting on contact region of spiral helical gear ' s surface validates theoretical analysis
利用計算機模擬了兩齒面在三維空間中接觸的情景;描繪了三維空間中相對速度的大小及方向;繪制了任意法截面上兩齒面法截線的圖形。對螺旋齒輪齒面接觸區進行了實驗研究,驗證了本文中數學模型及理論分析的正確性。The system eliminates the conventional rotating driving components, the absence of mechanical propeller system will lead to a reduction in the mechanical noise generated and make the arrangement of ship more expedient
由於磁流體推進取消了傳統的螺旋槳推進系統中的螺旋槳、傳動軸、減速齒輪等轉動裝置,因此,它具有噪音小、布局靈活等優點。Abstract : in this paper, the best selection of key parameter helix angle is discussed for all kinds of cross helical gear transmission in order to raise efficiency, reduce wear, obtain lighter weight and less size of bearing
文摘:從提高效率、減少磨損、減輕重量和較小軸承尺寸的角度出發,綜合探討了交錯軸斜齒輪傳動的各種組合中,關鍵參數螺旋角的最佳選擇分享友人