螺旋角 的英文怎麼說

中文拼音 [luóxuánjiǎo]
螺旋角 英文
[力學] helical angle; angle of helix; helix angle; pitch angle螺旋角檢查儀 helix angle tester
  • 螺 : 1. [動物學] （軟體動物） spiral shell; snail; conch 2. （螺旋形的指紋） whorl （in fingerprint）
  • 旋 : 旋Ⅰ動詞1 （旋轉） whirl 2 （用車床切削或用刀子轉著圈地削） turn sth on a lathe; lathe; pare Ⅱ名詞...
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  • 螺旋 : 1 （具有螺紋的圓柱體 屬于斜面類的簡單機械） corkscrewspin; screw; spiral; helix 2 （螺旋現象;尾旋...
  1. Base helix angle

    基圓柱螺旋角
  2. 2. the flux characteristics of ordinary helical gear pump are lucubrated by theory for the first time, on this condition the selective qualification of the helical gear pump is gained

    首次對普通斜齒齒輪泵流量特性進行了深入的理論研究，在此基礎上研究了全齒廓嚙合斜齒齒輪泵流量特性，首次得到了完全消除斜齒齒輪泵流量脈動的螺旋角的選擇條件。
  3. On the condition the trapping characteristics of whole profile meshing helical pump are lucubrated by theory for the first time, and the select range of the helical angle that can eliminate completely the trapping of whole profile meshing helical gear pump is also obtained

    在此基礎上，首次對全齒廓嚙合斜齒齒輪泵的困油特性進行了詳細的理論研究，得到了完全消除全齒廓嚙合斜齒齒輪泵困油沖擊的螺旋角的選擇范圍。
  4. 3. the trapping characteristics of ordinary helical gear pump are lucubrated by theory for the first time, the theoretic relation of the gear rotor between the end overlap coefficient and trapping phenomenon is discussed respectively with clearence or without clearcence, and the relation of trapping volume with the rotational angle turn is also discussed. the selective range of the helical angle that can eliminate completely the trapping of helical gear pump is gained, which never appeared in literature before

    首次對普通斜齒齒輪泵的困油特性進行深入的理論研究，分別討論了有側隙和無側隙時普通斜齒齒輪泵轉子的端面重合度與困油現象之間的理論關系，以及困油容積隨轉角的變化關系，得到了完全消除斜齒齒輪泵困油沖擊的螺旋角機械科學研究院博士學位論文的選擇范圍。
  5. Precise measurement for helical angle of cylindrical gears

    圓柱齒輪螺旋角的精密測量
  6. Helix angles for cylindrical gear teeth

    圓柱齒輪嚙合的螺旋角
  7. Helix angle at reference cylinder

    分度圓柱螺旋角
  8. Slow - helix straight shank drill

    小螺旋角直柄鉆頭
  9. We may find that the increasing of screw angle has large influence to the gear

    從這公式發現螺旋角增加對輪的影響是很大的。
  10. Involute spiral angle

    漸開線螺旋角
  11. U screw angle degree

    U螺旋角度數
  12. Inner spiral angle

    小端螺旋角
  13. Outer spiral angle

    大端螺旋角
  14. 4. the effects of geometrical parameters of microfin tubes on the in - tube boiling heat transfer coefficients is analyzed. in addition, the principles on intensifying heat transfer in microfin tube is also analyzed

    對r290和r404a ，通過研究koyama和thome關聯式，分析了內螺紋管齒高、螺旋角等齒型參數對工質沸騰換熱性能的影響。
  15. As the increasing of helix angle, the film thickness becomes more uniform

    隨著螺旋角的增大，螺旋槽管壁面上各處的液膜分佈趨向均勻。
  16. For cutting the composite lock gear with unequal tooth thickness, a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile. the cutter tooth arrangement, the choice of teeth number of the cutter and the basic method of cutter design are discussed ; and a new method of choosing deflection factor by using limited area is presented. and the curve of relationship between rear angle on tooth crest and helical angle on tooth side of the cutter is given so as to give a basis for the gear sharper cutter to choose its parameters. to design nonstandard gear sharper cutter by adopting the method mentioned above will simplify the calculation and will increase the efficiency of design

    研究加工不等齒厚的非標準參數漸開線齒形，與非漸開線齒形復合的鎖閉齒輪插齒刀刀齒的排列、刀具齒數的選擇以及刀具設計的基本方法，介紹用限制區域選擇插齒刀變位系數的新方法，並給出刀具齒頂后角與側螺旋角的關系曲線，為插齒刀參數的選擇提供依據.結果表明，採用上述方法設計非標準復合齒輪插齒刀，可簡化計算和提高設計效率
  17. The distribution of the liquid film was got, and the effects of helix angle, geometry of the channel, liquid mixing and liquid properties on the liquid film was also studied

    利用fortran語言編程，求解液膜的厚度分佈4研究槽道螺旋角、槽道幾何形狀、流體摻混、流體性質對壁面液膜分佈的影響5
  18. Abstract : in this paper, the best selection of key parameter helix angle is discussed for all kinds of cross helical gear transmission in order to raise efficiency, reduce wear, obtain lighter weight and less size of bearing

    文摘:從提高效率、減少磨損、減輕重量和較小軸承尺寸的角度出發，綜合探討了交錯軸斜齒輪傳動的各種組合中，關鍵參數螺旋角的最佳選擇
  19. It would be ready for virtual manufacture of ball - end cutters. firstly, the traditional cutting - edge models with constant helix angle of ball - end cutters are analyzed and the befitting normal helix models are proposed, and helical peculiarities of them are analyzed by definition of helix angle

    首先，本文對傳統的等螺旋角的球頭立銑刀刃口曲線的模型進行了分析，建立了正交螺旋線的刃口曲線模型，並運用螺旋角的定義分析了該刃口曲線的特點。
  20. Mean spiral angle

    中點螺旋角
分享友人
分享到 Line

分享到臉書