螺紋底 的英文怎麼說
中文拼音 [luówénde]
螺紋底
英文
bottom of thread-
Cycles. screw threads used in bottom bracket assemblies
自行車.底部托架組件用螺紋Implants for osteosynthesis - bone plates - specification for holes corresponding to screws with asymmetrical thread and spherical undersurfaces
骨接合術用外科植入物.第23部分:金屬接骨板.第3節:不對稱螺紋球形底面螺釘的螺釘孔Implants for osteosynthesis - bone screws and auxiliary equipment - specification for screws having symmetrical and asymmetrical thread and conical undersurfaces
接骨用植入物.接骨螺釘和輔助設備.有對稱和不對稱螺紋及圓錐形底面的螺釘規范Both of forward and back bearings have been integrated into one box to make full use of the length of base frame that the motor formerly mounted on, and short the shaft extended lengths in both end with the strengthening connection between bearing housing and screw thread of base
將前後兩支承設計為一個整體軸承座,充分利用原電動機安裝底座的有效長度,最大限度地縮短了軸的懸伸量,提高了軸承座與底座的螺紋聯接強度。The fatigue fracture occurred in the root of the screw where defects such as decarburization and cracks existed, and these defects made the zone to be a stress concentration area and caused the bolts to break finally
疲勞裂紋的形成是由於螺紋牙底存在脫碳和折疊裂紋等缺陷,這些缺陷的存在使該材料產生了較大的應力集中,從而導致螺栓開裂失效。Horology. closing notches for watch frames with screwed bottom
鐘表業.帶螺紋底板的表架關閉槽口Seven body bosses provide purge, flush, drain or bypass connections. ( purge / flush shown. ) bottom boss is furnished with standard pipe threads
七個閥體凸起部提供清洗,沖刷,排泄或旁路連接。 (圖示為清洗/沖刷) 。底部凸起部配置標準管道螺紋。For edge trimming of all kinds of round - shape stainless steel made metal wares and turning of compound bottom
I型車底機主要用於各種圓型不銹鋼器皿行壓成型后的修邊及復合底平面的環形槽底螺紋車削。En 2587 aerospace series. rod ens, adjustable fork and threaded shank. dimensions and loads
航空航天系列.帶螺紋桿和雙支架的可調底座.尺寸和負載En 2515 aerospace series. rod ends, adjustable simple fork and threaded shank. dimensions and loads
航空航天系列.帶螺紋桿和單支架的可調底座.尺寸和負載Undercuts and runouts for screw threads - specification for iso metric screw threads
螺紋牙底削平和收尾規范.第2部分: iso米制螺紋規范Core diameter of thread
螺紋底徑Recommendations for tapping drill sizes for use with fluted taps
帶槽絲錐用螺紋底孔鉆頭尺寸推薦標準Thoroughly clean threaded end to remove any harmful steel or iron deposits
要全面徹底地清理螺紋連接埠,清除任何有害的鋼鐵殘渣。Engineering drawing system can draw two dimension curve graphs, main detail drawing and assembly drawing. the curve of internal trajectory and dynamic simulation of particle external trajectory. the detail drawing includes the graph of chamber, grain design, connection body, nozzle, some standard part
工程繪圖可以繪制二維曲線圖和零部件圖,其中二維曲線包括有內彈道壓(推)力?時間曲線、質點外彈道動態模擬曲線;零部件圖包括有標準螺栓與螺紋孔、燃燒室結構圖、裝藥設計截面圖、連接底結構圖、噴管結構圖及火箭發動機總體裝配圖。Pneumatic fluid power. directional control valve with four ports. mounting surfaces of subplate. pipe thread
氣壓流體動力.帶4個口的定向控制閥門.底座安裝表面.管材螺紋Pneumatic fluid power. directional control valve with three ports. mounting surfaces of subplate. pipe thread
氣壓流體動力.帶3個口的定向控制閥門.底座安裝表面.管材螺紋Miniature fuses ; fuse carrier for 6, 3 a 250 v screw - in type ; fuse bases complying with din 41672 and din 41677
微型熔斷器. 6 , 3a . 250v螺紋擰入式熔斷器底座的絕緣支Cycles - specification for screw threads used in bottom bracket assemblies
自行車.第9部分:底托組件用螺紋規范Apply primer n to threads of female portion of assembly. allow 2 minutes to dry
給裝配件的雌性部件的螺紋施用底漆n 。允許乾燥2分鐘。分享友人