行波繞組 的英文怎麼說
中文拼音 [hángbōràozǔ]
行波繞組
英文
progression wave winding-
Powerformer have some changes in constract with the conventional generator ， subsequently it also have some new problems in order to have an economical ， efficient ， credible development and application the structure and the philosophy of electromagnetism of powerformer will be on speaking terms changes electrical design ， magnetism design ， thermal design and structural design are have some new changes above all ， the electromagnetism parameter and the harmonic magnetomotive force of powerformer are studied in this paper first ， it mainly utilizes analytics to deduce formula of slot leakage reactance it considers three instances ， including monolayer - slot ， multilayer isometric - slot and multilayer anisometric - slot then ， the analytics and the fem are utilized to calculate slot leakage reactance of stator winding of prototype of powerformer and compare their results second ， the theory of utilitzing fem to calculate the reactance of powerformer is simply introduced ， including stable reactance ， transient and subtransient reactance specially ， the saturated influence of the stable reactance is considered then ， the results are analysed final ， it mainly introduces the influence of harmonic magnetomotive force of stator winding and analyses the harmonic magnetomotive force of stator winding then ， it mainly analyse harmonic magneto - motive force of stator winding through arranging various arrays of stator winding and observe their influence
基於上述原因，本文對powerformer的電磁參數以及定子繞組諧波磁勢進行了研究。首先是用解析法推導出powerformer定子繞組槽漏抗的計算公式，考慮了單層圓形半閉口槽、多層等半徑圓形半閉口槽和多層不等半徑圓形半閉口槽三種情況，並對powerformer樣機的定子繞組槽漏抗用解析法和有限元法進行了計算，並比較其結果；其次，簡要介紹了有限元法計算powerformer電抗參數的原理，包括穩態電抗、瞬態電抗和超瞬態電抗，對穩態電抗考慮飽和影響，對結果進行分析；最後，介紹定子繞組諧波磁勢對電機運行性能的影響並對定子繞組諧波磁勢進行了分析。然後通過對定子繞組進行不同排列來分析定子繞組諧波磁勢，看看繞組排列對諧波磁勢的影響。In this thesis, the author analyses the deficiency in detecting and controlling function of the computer detecting and controlling system utilized in present transforming station. the strategy of design of software on operation and direction of 5 00kv transformer station is presented. it points out that we can deduce the mathematic analytical formula using the current, voltage and power of two terminals of transmission line as input. on this basis, we do realtime calculation of 500kv transmission line ' s parameter. we can also deduce the linear analytical formula of three - winding autotransformer ' s resistence using its current, voltage and power as input. the corresponding software is programmed on this basis
論文提出以輸電線路本端和對端電流、電壓、功率作為輸入量，導出了超高壓長線的波阻抗和傳播常數的數學解析式，在此基礎上進行了500kv輸電線路實時參數計算；提出以三繞組自耦變壓器的電流、電壓、功率為輸入量，導出了自耦變壓器繞組的電阻、電抗的線性解析式並進而對變壓器的實時參數進行計算；在此基礎上編制了相應的軟體。In current practice, array parameters are usually calculated according to the strength and types of interference wave, frequency characteristics, and azimuth, whereas the effect of array center is often ignored, and simply view the graphic center as array center
指出現在施工設計中，組合參數的確定主要圍繞干擾波、頻率特性和方位角等方面進行論證，忽視了其組合中心的確定。Based on the result, fault diagnostication according to fault recording data and locating the fault position of stator windings are p [ it forward for the first time, it is irmovative and practical
在此基礎上，首次提出用錄波數據進行故障診斷，確定接地點在定子繞組上的位置，分析失磁全過程，有創新、有實用價值。Based on the result, the fault diagnostication according to fault record data and locating the fault position of staor wtndings are put forwar for the first time, it is innovative and practical
在此基礎上，首次提出用錄波數據對定子繞組匝間短路和相間短路進行故障診斷，確定故障點在定子繞組上的相別和匝數，有創新、有實用價值。Linear induction motor is an important kind of machines which have some merits such as simple structure, low cost, durability, convenience for maintenance etc. the subject of this thesis is to study a big circular ring linear induction motor, and the major works in this thesis are summarized as follows : ( 1 ) considering the effects of the finite length of primary core, one - dimension analytical solution for the air gap field is cited in this paper. based on it, the single layer winding magnetic field is studied. considering whole - pitched and short - pitched winding configuration with odd poles and half - fulled slots in both ends, the double - layer winding magnetic field is analyzed, respectively
本文對大圓環直線感應電機進行了深入細致研究，內容包括： （ 1 ）本文採用有限長行波面電流作用於有限長鐵芯上的模型，引用了氣隙磁場一維解，研究了單層繞組磁場，奇數極半填槽雙層繞組在採用整距和短距時磁場的分析、比較，簡單介紹了二維解； （ 2 ）用有限元軟體ansoft對大圓環直線感應電機空載氣隙磁場進行了靜態分析，並分析了結果； （ 3 ）用軟體進行了額定電壓下的瞬態分析，得到了轉矩，位移，轉速隨時間變化曲線圖，利用單極性霍爾元件測定轉速並與軟體計算結果進行了比較，採用等效電路法計算了堵轉時的最大電磁力並做實驗進行了驗證，由實驗測得了三相電流波形，並與計算結果進行了比較，對其不對稱性進行了定性分析。First of all, we bring forward the basic project of tadil, which adapts to combined operations. it is suggested to use tdma ( the abbreviation of time division multiple access ) as the working pattern and utilize the concept of mobile ad hoc network to construct the data link network. aiming at the impact of time delay on data link and the characteristic of cooperative combat under the command of director aircraft, this thesis applies a kind of kalman filtering algorithm in polar coordinates to compensate the error of time delay, and then does the transformation of target motion parameters to obtain the current information of target
本文結合空軍裝備部某「十五」預研課題，圍繞著戰術數據鏈、多機協同多目標攻擊、超機動攻擊、空對地攻擊這四個方面展開了一系列的研究工作:本文首先給出了適應三軍聯合作戰的戰術數據鏈系統的基本方案，建議採用時分多址的工作模式，並利用移動自組織網路的概念構建數據鏈網路，同時針對數據鏈傳輸信息的時間延遲特性和指揮機指揮下的多機協同作戰特點，應用一種極坐標系下的卡爾曼濾波演算法對該傳輸延遲誤差進行補償，並在此基礎上進行目標運動參數的轉換，以獲得目標相對于某無人機的當前運動信息，且利用模擬驗證了方法的有效性。In accordance with the driving characteristics of ac driving locomotive, the working status of its traction transformer is analysed. the questions that should be considered in the traction transformer design of ac driving locomotive are mentioned. these questions are the large short - circuit impedance of traction winding, higher harmonic current, over - excitation and dc magnetization caused by large variation of the network voltage, etc. some disposal methods are given
針對交流傳動電力機車的傳動特點，對其中的牽引變壓器的工作狀態進行了分析，指出交流傳動電力機車用牽引變壓器設計時需考慮的牽引繞組的短路阻抗大、電流的高次諧波、網壓波動大可能引起的過勵磁以及直流磁化等問題，同時給出了相應的一些解決方法。Dissertation explains the theory and characteristices of switched reluctance motor based on its idealy linear math mode. analyseing and researching on control characteristic, control parameters, control strategy and their relationship, thesis designed hardware circuit and software of control system based on the strategy. dissertation discussed the transform function of system and illustrates it is essential to chang parameters in the pid control arithmetic, estimating parameters for the digital pid controller primarily, dissertation also researched on the exciting and protection of igbt
論文以開關磁阻電動機的理想線性數學模型為理論基礎，對其原理特性進行了說明，對開關磁阻電動機的控制特性（轉速、轉矩） 、可控參數（導通角、關斷角、相電流、繞組端電壓）與控制策略（電流斬波、電壓斬波、角度位置控制等）及它們之間的關系進行了研究和分析。Then a thorough analysis to the bias - magnetic of ppfc is made. the retraining effects of the main parameters ( include clamping capacitance c, output filter inductor lf, load r, the leakage inductor ls and source winding resistance r ) are studied under the conditions of different von, different ton and different winding parameters. then a conclusion can be drew, that the smaller lf and the bigger r are, the better the bias - magnetic is restrained and c has a best value to retrain the bias - magnetic
分別對管壓降不同，導通時間不同以及兩原邊繞組參數不一致（包括漏感、電阻、激磁電感三種情況）的情況下，主要參數（包括箝位電容c 、輸出濾波電感lf 、負載r 、原邊繞組漏感ls 、原邊繞組電阻r ）對偏磁的抑制作用進行了模擬分析研究，得出lf越小， r越大時激磁磁勢偏移量ni越小， c在其他參數確定時對抑制偏磁有最優值等結論，為參數的優化設計提供了依據。Abstract : based on the classical theory, the harmonic winding potential of the tooth harmonic brushless exciting generator have been calculated and analysed. the results tally with the data of no - load test very well. it was demonstrated the designing thread of harmonic winding is correct
文摘:從經典理論出發，對齒諧波無刷勵磁發電機的諧波繞組電勢進行了分析計算，其結果與空載實驗得出的數據完全吻合.說明諧波繞組的設計思路是正確的The thesis realizes the control exciting winding method and the best exciting in towards polarity method provided in this thesis with singlechip ( at90s8535 ) and scr hardware. it proves these methods are accurate and available through the control exciting winding test. analyzing the stator current and exciting current test curves on a salient - pole synchronous motor with 2kw - 4 poles, it solves the starting - difficulty of salient - pole synchronous motors, and improves motors " starting capability
通過在一臺2kw 、 4極凸極同步電動機上進行異步起動試驗和分析試驗過程中的勵磁繞組電流和定子繞組電流的波形，證明了本文提出的勵磁控制線路的正確性和可行性，較好地解決了凸極同步電動機起動難的問題，同時改善了電機的起動性能。Considering the influence of damping winding and if core is saturated or not, the no - loading emf waveform of a conventional generator having the same size with the prototype ( except the stator slot ) is analyzed, and the waveform deviation factor is taken out
對一臺具有與電力發生器樣機相同尺寸（除定子槽形）傳統發電機的空載電勢波形進行了分析。分析了不考慮鐵心飽和、考慮阻尼繞組影響和考慮鐵心飽和、考慮阻尼繞組影響兩種情況下，它的空載感應電勢，求取了空載電勢波形畸變率。Both software and hardware are synthesized. three - phase bridge inverter used, the current in each phase is made similar to sine wave using current closed loop control
以igbt三相橋作為主逆變電路，對電機繞組電流按正弦規律進行電流閉環控制實現正弦波細分驅動。Also discussed the methods on how to realize the cwt both in time - domain and frequency - domain and how to design the gm - c bandpass filter used in realization of cwt. in order to optimize the performance of gm - c filter, linearization techniques are investigated and proposed. due to process variation and parasitics, an automatic tuning is designed for center frequency / 0 and quality factor q also, in this thesis, 16 - channel analogue cmos cwt circuit has been realized
論文圍繞連續小波變換的模擬電路實現這一熱點問題，討論了連續小波變換的時域和頻域實現方法；具體分析了并行結構與串列結構的優缺點；研究了頻域法中的跨導-電容帶通濾波器的設計；給出了改善跨導輸入級傳輸特性的線性程度並擴大線性范圍的具體方法；設計了片內自校正（可調諧）環節使濾波器參數自動調整到設計標準值；最後給出了16通道濾波器組實現小波變換的方法。Firstly, a method to estimate the rotor speed, which is based on bp neural network, is introduced in this paper. secondly, the park vector approach is used to monitor and diagnose the inter - turn fault of the stator winding. finally, this paper studies thoroughly a novel approach to detect rotor bar breaking fault, which is based on the perfect combination of the hilbert transform and digital filter
具體工作如下：採用bp神經網路對異步電動機轉子轉速進行無速度傳感器估計；對定子繞組匝間短路故障，採用派克矢量方法進行監測與診斷；對于轉子斷條故障，詳細介紹了一種新的基於希爾伯特變換與數字濾波的在線監測方法。This paper briefly introduces work principle, primary characteristic index and several kinds of driving circuits of stepping motor. accordingly, the paper puts forward a kind of practical method of divided driving of stepping motor. that is, it is cutting wave constant current to drive stepping motor based on single chipped microcomputer dealing with divided current
本文簡要地介紹了步進電機的工作原理、主要性能指標及幾種驅動電路，在此基礎上提出了步進電機的細分驅動的實現方法，即利用單片機來處理步進電機繞組的細分電流基礎上進行斬波恆流驅動。The product is constructed with foil type lv windings and hermetically sealed corrugated oil tank with the characteristics of low leakage flux, low losses, high strength, fine heat distribution, no leakage, maintenance free, beautiful outline, reliable opertion and long operating life
產品採用箔式繞組波紋油箱全密封結構漏磁少強度高損耗小散熱好不滲漏免維修外型美觀運行可靠使用期限長。The product is constructed with foil type lv windings and hermetically sealed corrugated oil tank with the characteristics of low leakage flux, low losses, high strength, fine heat distribution, no leakage, maintenance free, beautiful outline, reliable operation and long operating life
產品採用箔式繞組波紋油箱全密封結構漏磁少強度高損耗小散熱好不滲漏免維修外型美觀運行可靠使用期限長。分享友人