行程輪 的英文怎麼說

中文拼音 [hángchénglún]
行程輪 英文
traveling wheel
  • 行 : 行Ⅰ名詞1 （行列） line; row 2 （排行） seniority among brothers and sisters:你行幾? 我行三。where...
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 行程 : 1 （路程） route or distance of travel; distance of run; length of travel; distance travelled; jo...
  1. The practical issue of drum brake with oversized overall stroke was resolved by experiments, and it indicates that major effect factors of air chamber overall stroke, which are the drum - shoe clearance, the elastic modulus of lining, the torsion deflection of cam shaft

    研究結果表明，氣室推桿總行程過大的主要影響因素為制動蹄與制動鼓之間的間隙、摩擦片的彈性模量、凸輪軸的扭轉變形。
  2. The frequency curve of transverse distribution of the wheel track on divided ways reveals that the frazzled damage of highly channelizing expressway cement concrete pavement largely occurs in the peak range of distribution curve of the wheel track

    摘要分車道行駛輪跡橫向分佈頻率曲線顯示，渠化程度較高的高速公路水泥混凝土路面磨損破壞主要集中在行車道輪跡峰值范圍。
  3. Types and principal parameters of planetery wheel reductor for driving axle in wheel type construction machinery

    輪式工程機械驅動橋行星輪邊減速器型式和基本參數
  4. Take special attention to avoid the grinding wheel hitting grinding head or the tailstock, while operating the handle of the worktable or adjusting its stroke

    搖動工作臺，或調節行程時要特別注意避免砂輪撞上磨頭或尾座。
  5. The drama performance was about the transmigration of a spiritual practitioner. at first, the main actor played the role of the devil, after which he transmigrated and became an animal, then finally a human

    第三個部分是戲劇與音樂的演出，演出一位修行人輪回的過程，最後找到觀音法門跟清海無上師修行。
  6. Abstract : in this paper, the kinematically admissible velocity fields are established by using the metal flow patterns based on the experiments, and the configuration dimensions of billet and the curves of load - stroke in precision forging process for spur gear from solid billet are simulated on computer by upper bound method. the results acquired in the simulation are in good agreement with those obtained in the experiments

    文摘:本文利用有實驗根據的變形流動模式建立動可容速度場，利用上限法模擬用實心坯料精鍛直齒圓柱齒輪時坯料的外形尺寸變化和力?行程曲線，所得結果與實驗測定值很一致，可供沖擠精鍛工藝設計參考。
  7. By means of the optimization method - punishing function method and taking the sum of the planet gear radius and center distance as the target function, the parameters of drive are optimized. by using the optimization program, the initial serial studies of drive are completed, the best serial parameter value of the drive is given

    採用外點罰函數優化方法，通過取行星輪半徑和中心距之和作為優化目標函數，對滾錐齒超環面行星蝸桿傳動進行了參數優化，運用此優化程序，初步完成了對該種傳動的系列化研究，給出了傳動系列的最佳參數取值。
  8. The programme logic controller is utilized to control the inverter ' s output frequency which accomplishes controlling the velocity of speed - controlling asynchronous moter. the velocity between main asynchronous moter and speed - controlling asynchronous moter is composed by way of the differential planetary gear train, the tranmission system is made to regulate velocity stepless in large scope which succeed in controlling starting progress of load

    使用可編程式控制制器對變頻器的輸出頻率進行控制，實現對調速電機轉速的控制。調速電機與主電機的轉速經差動行星輪系的速度合成，可使傳動系統在很大范圍內無級調速，實現對負載的可控起動。
  9. A method based on the application of an injection process analysis software is introduced in this article, which optimize injection process through changing the design of fuel - injection pump cam. a model of 1115 single cylinder direct injection diesel engine is used as an example. with the help of pre - journey optimization, increasing cam lift and using tangent - function can make the matching of the injection system with the diesel more reasonable. without changing fuel pump installing size, it can enhance injection rate and injection pressure and improve the diesel operating stability in low speed condition

    本文以國產1115型單缸直噴柴油機為例，介紹一種應用噴油過程分析軟體改進噴油泵凸輪設計的方法，通過增大噴油泵凸輪升程、採用切線函數凸輪並優化預行程的方式，在不改變噴油泵安裝尺寸的前提下，可提高噴油壓力和噴油速率，改善柴油機低速工作穩定性，使噴油系統與柴油機匹配更合理。
  10. A loop for calculating the fuel heating power on line by enthalpy is described together with the setting of its important arithmetical parameters

    輪發電機組制動風閘的位置檢測，因習慣上採用機械式行程開關，導致故障率高，檢測可靠性差。
  11. According to the tappet displacement curve, the design of cam profile can be carried out by " reversal method " theory

    根據得到的挺柱升程曲線，利用「反轉法」的原理進行凸輪輪廓曲線的設計。
  12. While according to dynamics correction method, the valve displacement curve has to be design, which can be acquired by boundary condition and calculation method. then by dynamics analysis, the tappet displacement curve equation can be obtained based on the dynamics differential equation. thus, the design of cam profile can be carried out based on the tappet displacement curve equation

    按照動態設計的動力學修正方法進行設計時，又得先進行氣門升程曲線的設計，利用一定的邊界條件和計算方法得到氣門確定的運動規律，再通過動力學分析，根據建立的動力學微分方程，經過計算得到挺柱的升程曲線方程，至此，就可以根據挺柱的升程曲線進行凸輪輪廓曲線的設計。
  13. For solving the existing problems of machine braking and electrical braking during the process of stoppage of a turbogenerator set, a magnetic reducing method is recommended, which can greatly reduce the current of generators at switch due to remainder magnetic and abate the demand for braking switch

    摘要針對水輪發電機組在停機過程中，目前廣泛採用的機械制動和常規的電氣制動中所存在的問題，提出了採用減磁法來進行水輪機發電機組的電氣制動。
  14. Secondly, to counter contour curve for large sole of rubber overshoes, the way of linear circle arc spline of two dimensions curve fitting has been raised in this paper and autocad has meanwhile been applied in cad / cam integeration system of rubber overshoes mould, and also a whole set of software and hardware technique developed, and the selecting way for optimizing tool path worked out. this way may make nc machining free running minimun

    其次，針對膠鞋大底的輪廓曲線，對圓弧樣條進行了深入研究，提出了二維曲線擬合的線性化圓弧樣條方法；同時將autocad應用於膠鞋模具cad / cam一體化系統中，成功地開發了一整套相應的軟硬體應用技術，提出了刀具軌跡優化的動態選擇法，以便使nc加工的空行程相對極小化。
  15. The test results showed, that the test method accorded with the requests in engineering tests, that bearing vertical and horizontal loads can be tested in real - time

    試驗結果表明：該方法滿足工程測試要求，能實時測試各支承負荷及其變化，可運用於現場進行汽輪發電機組軸承負荷在線監測。
  16. First, the normal vector of the surface was calculated using the differential geometry based on the features of an involute and a cycloid as a reference of radius of the ball milling cutter

    由於銑刀每完成一個行程后，還要進行輪廓插補，採用一種新的漸開線輪廓插補方法，並將插補軌跡換算成球頭銑刀的刀心軌跡。
  17. Vertical clearance of wheel

    車輪垂直行程
  18. With the help of dynamic qualitative information of working marine diesel power equipment in this field and expertise, a new long - distance oil monitoring expert system of marine diesel power equipment has been proposed and developed with the characteristic of expounding the dynamic features of marine diesel power equipment from the perspective of chaos knowledge, possessing intellectualized auxiliary decision - making mechanism based on fuzzy reasoning and neural network reasoning, utilizing mathematic analysis model established by means of track facility states of chaos vector and capable of evaluating the analysis results of oil monitoring facil ity ' s development of engine power and its working conditions accurately

    然後，結合廣泛搜集的本研究領域內船舶柴油機動力裝置在運行中的動態定性信息與專家經驗，研製開發了運用混沌學的觀點闡釋船舶動力裝置的動力特性，並擁有基於模糊推理與神經網路協作推理的智能化輔助決策機制，採取通過求取設備狀態混沌向量等方法建立的數學分析模型進行數據分析，能準確地評價船舶柴油機動力裝置油液監控設備狀態變化趨勢及其運轉狀況的遠程輪機油液監控診斷專家系統。本文研製開發的遠程輪機油液監控診斷專家系統在internet intrabet網路環境下，具有遠程智能專家診斷的特點。
  19. Abstract : in this paper, a kind of technological scheme for one - step precision forging spur gear with large module is put forward by using positive friction role. experiment, in which commercial pure lead is taken as test material, is done in the special die designed, and force vs. stroke curve is recorded. it is shown that positive friction role can efficiently make a contribution to the filling of the tooth cavity, but increase forming force

    文摘:針對大模數直齒圓柱齒輪，提出了利用積極摩擦一步成形的工藝方案，並用工業純鉛作為試驗材料，在設計的專用模具上進行試驗，記錄了力? ?行程曲線，結果表明：利用積極摩擦作用能夠有效地保證直齒圓柱齒輪精鍛時齒腔充滿，但同時增加了變形力。
  20. We also offer seattle and san francisco departure round - trip save money on airfare alaska cruise itineraries, please check with us for details

    我們另有由西雅圖以及由舊金山出發來回程可以省不少機票錢的阿拉斯加游輪行程，請洽詢詳情。
分享友人
分享到 Line

分享到臉書