裝甲厚度 的英文怎麼說
中文拼音 [zhuāngjiǎhòudù]
裝甲厚度
英文
armor thickness-
This tactic epitomizes speed and maneuverability over brute armor
這個戰術概括起來就是速度和機動性超越厚裝甲。Russia kv - 1 1942 heavy cast turret tank because warlike vehemence, the kriov factory gave birth to casts the kv - 1 of the quick - fried tower, nameding after the kv - 1 model 1942 heavy cast turret, turret in this kind of foundry contain better bullet - proof features, the armor thickness also comes to 95 mm of, the main firecrackers also changed to pack better types zis - 5s in function 76. 2 mm artillery
因為戰爭的激烈,基洛夫工廠kroiv生產了鑄造炮塔的kv - 1 ,命名為kv - 1 1942年型重型鑄造炮塔,這種鑄造炮塔有更好的防彈外型,裝甲厚度也達到了95毫米,主炮也換裝了性能更好的zis - 5型76 . 2毫米炮。In this paper, firstly the macro parameter of the series connection app was comprehensively analyzed, among which the trajectory location of the bullet emission and the terminal velocity of the bullet were mainly analyzed, and the feasibility of the series connection app to cope with explosive reactive armor was demonstrated. and then the macro design about the head of the series connection app was made, among which a particular analyse about the bullet " s launching process was made, from which we concluded the relation between the thickness of the airproof loop and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the burning rate of the powder and the relation between the length of the bullet and the maximum pressure of the emission hole and the relation between the length of the bullet and the emitting time of the bullet, and the reasonable str ucture of the head of the carrier and bullet were designed, then the intensity of the head of the carrier was checked out using of the software of ansys
本文首先對子母式穿甲彈總體參量作了全面的計算分析,其中主要分析了子彈射出的彈道位置和必要的子彈著靶速度,論證了子母式穿甲彈對付爆炸式反應裝甲的可行性,然後對子母式穿甲彈彈頭部進行了總體設計,其中主要對子彈的發射過程進行了詳細的分析,得出了母彈彈頭部發射孔內閉鎖環厚度與子彈飛離母彈速度的關系、子彈長度與子彈飛離母彈速度的關系、子彈長度與火藥燃燒率的關系、子彈長度與母彈彈頭部發射孔內最大壓力的關系以及子彈的長度與子彈發射所需時間的關系,設計出了合理的母彈彈頭部結構和子彈的結構,並利用ansys有限元分析軟體對母彈彈頭部的強度進行了校核。To solve the problem of the fear of inadequacy of armor protection on the already heavily armored kv - 1 model 1941, it was decided to bring the armor protection of the turret up to a thickness to 75mm. since the capability of producing such a thick armor plate was lacking at the time, so an interim solution was to use bolt on armor, 25 mm of thickness, bolt directly to the outside of the turret and some other parts of the hull. this type was usually referred to as kv - 1s ehkranami
針對kv - 1 1941年型的裝甲防護能力不足的問題,設計人員進行了一系列強化裝甲的工作,改進后的kv - 1的炮塔裝甲達到了大約75毫米的厚度但在具體製造中由於為kv坦克提供裝甲鋼板的工廠沒有能力生產必要厚度的裝甲鋼板,因此,作為臨時解決方案用螺栓在車體和炮塔上加裝了25毫米厚的附加裝甲,這種改進的kv坦克被命名為kv - 1附加裝甲型。Point of impact : upper center near joint with turret roof at 0. 33 obliquity from normal where plate was 25. 99 " thick
撞擊點:以0 . 33的入射角撞擊炮塔根部結合部附近中上部的裝甲,厚度為25 . 99 " 。Where wheeled vehicles are stowed or used on insulated decks, when the permissible loading of decks is determined based on the thickness of decks, attention is to be paid to effect on insulated coating due to deck deformation
例4 :如具有絕緣層的甲板上裝載或使用車輛,則在根據甲板厚度確定用板的允許載荷時,應注意甲板變形對絕緣層的影響。分享友人