裝置驗收 的英文怎麼說

中文拼音 [zhuāngzhìyànshōu]
裝置驗收 英文
plant acceptance
  • 裝 : Ⅰ名詞1 （服裝） dress; outfit; attire; clothing 2 （演員的化裝品） stage makeup and costume Ⅱ動詞...
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 收 : Ⅰ動詞1 （把攤開的或分散的事物聚集、合攏） put away; take in 2 （收取） collect 3 （收割） harvest...
  • 裝置 : 1 （機器設備的配件）installation; device; apparatus; equipment; arrangement; gear; appliance; rig...
  • 驗收 : check and accept; check before acceptance; check upon delivery; acceptance check; control reception
  1. Test method for calorimetric determination of hemispherical emittance and the ratio of solar absorptance to hemispherical emittance using solar simulation

    用太陽模擬裝置作陽光吸收與半球發光量的比率及半球發光量的熱量計測定的試驗方法
  2. The article provides the demonstrations of the light source, transmitting / receiving set and homochromor. the whole work is to fix on the sets and select the parameters of them. at the end of the design of sets, a whole set is achieved by assembling the three main parts

    本文在實驗裝置的設計方面，主要對包括光源、收發裝置、單色儀等部分進行了充分論證，確定了光源和收發裝置，對單色儀的參數進行了計算與選擇；在硬體設計的最後部分，對整個實驗裝置進行了系統整合，使之成為了一個有機的整體。
  3. In addition to military products, criaa designed & manufactured many kinds of industrial products such as ff series servovalves, lpg recovery plant, airport hydrant refuelling equipments, hydraulic pump stations, hydraulic control system and testing equipments, low temperature box with natural air cooling, and air refrigerators used for mines etc

    產品除軍用外，開發的民品有： ff系列伺服閥、油田氣輕烴回收裝置、機場栓式加油設備、液壓控制系統產品及試驗設備、空氣製冷低溫箱、礦用空氣製冷機等。
  4. On the theory, the predictive function control method based on the state space is discussed and the simulation results validate the pfc method ' s advantages on robust and anti - jamming comparing with pid method by computer simulation. the application research includes the application of the software of predictive function control ( apc - pfc ) and the software of the multiple - variables predictive control ( apc - hiecori ). the former were applied in the temperature control chlorinating process and ph control in the process of zymolysis of penicillin, the latter were applied in the advanced control of reclaim equipment of lox in china petroleum & chemical corporation yangzi petrochemical co., ltd

    本文主要從理論和應用兩方面對預測控制方法進行了研究，理論方面主要是從預測函數控制的基本原理出發，研究了一般情況下的基於狀態空間描述的預測函數控制策略，並通過計算機模擬驗證了pfc演算法比常規pid演算法具有更好的魯棒性和抗干擾性：在實際工業過程的應用上，又分為兩類演算法及軟體的應用，預測函數控制策略及apc - pfc軟體的應用主要以聚乙烯氯化過程的溫度控制和青霉素發酵過程的ph值控制為主，多變量預測控制演算法和apc - hiecon軟體的應用主要以揚子石化公司的液化氣回收裝置先進控制為主。
  5. The acceptance standard of water and steam integrated sampling and on - line analysing unit

    水汽集中取樣分析裝置驗收標準
  6. Acceptance code for gear units - test code for airborne sound

    齒輪裝置驗收規程.空氣中噪聲試驗規程
  7. Acceptance code for gear units - part 1 : test code for airborne sound

    齒輪裝置的驗收規范第1部分：空氣傳播噪聲的試驗規范
  8. The recovery of atmospheric light oil yield of atmospheric in the northern atmospheric distillation tower of shenghua teaching & test factory, science and technology group of china university of petroleum has been increase by about 4 or 5 percent through the following methods : changing the tray perforation of atmospheric tower, adjusting the amount of stripping steam and the outlet temperature of the atmospheric heater and merging atmospheric excess vapor into 3rd atmospheric drawn - stream to keep the fractions content of bottom oil below 5 % before 350

    摘要中國石油大學科技集團勝華教學實驗廠北常減壓蒸餾裝置換煉勝利管輸油后，通過改變常壓塔塔盤開孔率、調節常壓塔汽提蒸汽量和常壓爐出口溫度、常壓過汽化油併入常三抽出線等措施，控制常壓塔底油350前餾分含量小於5 % ，使常壓輕質油收率提高約4 % ~ 5 % 。
  9. Code for construction and acceptance of battery electric equipment installation engineering

    電氣裝置安裝工程蓄電池施工及驗收規范
  10. The research on bypass carrier wave protection not only possess his theory value - studied protector ' high frequency signal as well as and dispatch signal logic, penetrate into learn protector ' occlusion type carrier wave protection logic about, but also has important signality in fact ? rovide practice system operation scheme with theory and test evidence

    對旁路代路時高頻保護配對方案的研究不僅具有其理論價值?對保護裝置的高頻信號以及收發信邏輯進行研究，深入了解保護裝置的閉鎖式高頻保護邏輯，而且具有較大的現實意義?為實際系統運行方案提供理論和試驗依據。
  11. In order to observe process and study the rule of producing and collecting dust, and to study the performance of high - voltage electrostatic dust - collecting system, a set of analog device is designed based on on - site measure for workshop of unloading coal of qing huangdao port

    對秦皇島煤碼頭翻車機房進行實地測量，設計製造了試驗模擬裝置。觀察翻卸作業起塵與收塵的物理過程，描繪起塵量與收塵量之間的變化規律。檢驗了高壓靜電除塵器的工作性能。
  12. Erection works of electrical installations code for construction and acceptance of battery

    電氣裝置安裝工程蓄電池施工及驗收規范
  13. Erection works of electrical installations code for construction and acceptance of bus - bar device

    電氣裝置安裝工程母線施工及驗收規范
  14. Erection works of electrical installations code for construction and acceptance of cable levels

    電氣裝置安裝工程電纜線路施工及驗收規范
  15. Glycol was the fit solvent. one set of extractive experiment equipment with continuously feed was designed and established to validate the extractive distillation and extractive distillation with salt. good results of the two technology processes and the extractive solvent recycling experiment were gained respectively

    本文還設計安裝了一套實驗室連續進料萃取裝置進行工藝的驗證實驗，對萃取精餾和加鹽萃取精餾工藝流程分別進行了驗證，並對萃取劑的回收利用進行了實驗，取得了良好的效果。
  16. Mountaineering equipment - energy absorbing systems for use in klettersteig via ferrata climbing - safety requirements and test methods ; german version en 958 : 1996

    登山設備.攀登用能量吸收裝置.安全性要求和試驗方法
  17. Development and application of a dynamic linear contraction setup for foundry alloys

    鑄造合金動態線收縮實驗裝置的研製與應用
  18. In an investigation, the hard packing was used to isolate the seal oil from the process fluid for recovering the seal oil from the catalytic hot oil pump

    在回收催化熱油泵密封油的試驗中，用硬填料作為密封油和介質的隔離裝置。
  19. By means of inspection analysis, the reasons of surface cracking forming were found out, which existed on the three towers in a wax catalysis unit, and the countermeasure of controlling surface cracking forming were proposed

    摘要通過檢驗分析，找出了某蠟油催化裝置吸收穩定三塔連續多年出現表面裂紋的原因，並提出了有效的防護措施。
  20. Acceptance conditions for copying attachments, integral or otherwise, for lathes - testing of the accuracy

    車床用整體式或非整體式仿形裝置驗收條件.精度檢驗
分享友人
分享到 Line

分享到臉書