裝載循環 的英文怎麼說

中文拼音 [zhuāngzǎixúnhuán]
裝載循環 英文
filling cycle
  • 裝 : Ⅰ名詞1 （服裝） dress; outfit; attire; clothing 2 （演員的化裝品） stage makeup and costume Ⅱ動詞...
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 循 : 循動詞（遵守; 依照; 沿襲） follow; abide by
  • 環 : Ⅰ名詞1 （環子） ring; hoop 2 （環節） link 3 （姓氏） a surname Ⅱ動詞（圍繞） surround; encircle;...
  • 裝載 : freight; loading; shipping; capacity; storage; embarkation; laden
  • 循環 : circulate; circle; round; repeat; loop; period; recurrence; cycling; circulating; mixing; circula...
  1. The extruders drived by d. c motor with a thyristro to stepless regulate. it also equipped with the over - load prtection and stoppage alsrmingsystem. the screws core and the outside of barrels are cooled by the circulation of oil, ther fuctions include vacuum venting and forced feeding

    本機採用直流電機，可近期硅無級調速，沒有過載保護和故障報警、螺桿芯部油循環恆溫、機筒油冷卻，並裝有真空排氣管裝置和定量喂料裝置。
  2. Traditional hydronic sizing methods can be used for selecting pumps, expansion tanks, heat exchangers, and air removal devices, as long as the heat transfer liquid ' s thermal properties are considered

    傳統的液體循環加熱體量法在泵、蒸發器、熱交換器和空氣移動裝置的選擇中可以應用，在考慮載熱流體的熱血特性的情況下。
  3. Finite element method ( fem ) was used to simulate thermal and vibration problems in stacked - die csp assembly. finite element models and apdl programes were built in ansys to conduct thermal, thermal - mechanical and vibration analysis. the aim of these researches were trying to find some possible reasons and trends which affect the reliability of stacked csp / bga assembly and give some useful suggestions for the packaging design

    本論文正是針對以上情況，以採用引線鍵合工藝的三維疊層csp / bga封裝（裸晶元疊裝）為研究對象，在有限元分析軟體ansys中建立相關的有限元模型，編制了相應的apdl參數化分析程序，進行了溫度場分析、熱循環加載下的snpb合金焊點疲勞分析和實裝pcb板的振動模態分析。
  4. Telecommunications - interface between carriers and customer installations - analog voicegrade switched access lines using loop - start and ground - start signaling

    電信.載體和用戶裝置間的介面.用於循環啟動和接地啟動信令的模擬音頻轉換訪問線路
  5. To our knowledge, for real flip chip packaging under the thermal loading, the paris equation obtained from experiment da / dn and simulation g is firstly reported here, and will be useful practically

    本文在熱循環加載條件下對實際倒裝焊封裝給出實驗da / dn和模擬g關系的paris方程，屬首次報導。
  6. 2. the delamination at the interface is one of typical failure mode for electronic packaging. in order to get more understanding of the propagation behaviour of [ he delamination, a series of finite element simulations related were done

    為了對界面分層及其傳播行為進行深入研究，本文對b型和d型兩種實驗倒裝焊封裝，在熱循環加載下，進行了有限元模擬。
  7. Basing on the method of approximate mechanics, the mechanical behavior and fatigue fracture characteristic of steel bridge asphalt mixture surfacing under repeated load was analyzed

    摘要採用力學近似方法，對鋼橋面瀝青混合料鋪裝層在循環荷載作用下的力學行為和疲勞損傷特性進行了理論分析。
  8. The study result is listed as follow : the transformation pseudo - elasticity property of shape memory alloys is simulated exactly with the above mentioned method of value calculation. the shape memory alloys re - centring damper presents typical " double flag " hysteretic curve, and the result accords with the theory analysis. the property of above new isolation device is excellent, the seismic response of the super - structure is significantly reduced, and the fully re - centring capacity after earthquake is obtained

    研究結果表明，文中所提的數值求解方法能夠反映形狀記憶合金相變偽彈性的基本特徵；形狀記憶合金自復位阻尼器在循環荷載下呈現出典型的雙旗型滯回曲線，程序的模擬結果與理論分析相吻合；這種新型隔震裝置的性能優良，既可以大大減輕地震對上部結構的影響，同時也具有很好的震后自復位功能。
  9. Output signal of the mechanically unloaded transducer with mounting parts at the start of a loading cycle

    在裝載循環起點有固定部件的機械空載力傳感器的輸出信號。
  10. According to the stress spectrum of weaking section in fatigue test and s - n curve of classic welding joint in this section, we establish a model of life calculating by the principle of fatigue damage equivalence, then we get the relationship between the cross sustaining device ' s actual utilizing life and the load recycle number in fatigue test

    根據疲勞薄弱部位在室內疲勞試驗中的應力譜及該部位典型接頭的s - n曲線，按照疲勞損傷等效原則建立交叉支撐裝置的壽命預測模型，得到了交叉支撐裝置實際運用壽命與室內疲勞試驗加載循環次數的關系。
  11. The stress result of assembly process and loading process was exchanged with the ansys special function on external data file. and the stress of leaf spring under virtual condition was calculated by the operation of array vectors of model results, which were generated from the external data file

    通過外部文件完成裝配階段向加載階段跨模型的應力結果數據的傳遞，然後在加載階段模型中進行兩階段模型應力數據的合成運算，得到鋼板彈簧實際工況下的完整應力循環。
分享友人
分享到 Line

分享到臉書