裝配間隙 的英文怎麼說

中文拼音 [zhuāngpèijiānxì]
裝配間隙 英文
assemblies clearance
  • 裝 : Ⅰ名詞1 （服裝） dress; outfit; attire; clothing 2 （演員的化裝品） stage makeup and costume Ⅱ動詞...
  • 配 : Ⅰ動詞1 （兩性結合） join in marriage 2 （使動物交配） mate （animals） 3 （按適當的標準或比例加以...
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 隙 : 名詞1 （縫隙; 裂縫） crack; chink; crevice 2 （空閑） gap; interval 3 （漏洞; 機會） loophole; op...
  • 裝配 : assemble; fit together; fit out; assembling; fitting; rigging; erecting; fabrication
  • 間隙 : （空隙） interval; gap; freedom; space; [機械工程] clearance; separation; stricture; clear; inter...
  1. Based on the analysis and practice of the ultrasonic soldering process, the results show that it is important to procure high soldering quality on controlling submersion depth, the ultrasonic soldering time, assembling clearance and solder composition

    根據對超聲波釬焊工藝的分析和實踐，結果表明控制產品在釬焊時的浸沒深度與產品裝配間隙、超聲波釬焊時間和釬劑成分是獲得高釬焊質量的重要條件。
  2. When machining parts with bore as positioning reference, if clearance fit positioning is adopted, machining accuracy is certainly affected due to the existence of clearance

    摘要在精加工以內孔為定位基準的零件時，所用芯軸類工裝如果採用間隙配合定位，由於定位間隙的存在，必然影響零件的加工精度。
  3. The friction is low and can move freely both in redial and in axial directions, and the bearing is in high precision

    產品具有摩擦系數低，軸向、徑向都能運動的特點，依靠滾動摩擦，實現無間隙裝配，保證了使用精度。
  4. Meanwhile it retains evenness on lift force to prevent leakage of residue that is caused by installation clearance error or changes in welding criteria, flow off molten iron as well as break - over welding, so that the ideal fosion depth and finishment have been fulfilled

    在需原動力的條件下，該機利用彈性夾角變化，隨著筒體轉動，使墊層焊劑始終緊貼筒體外側環向焊接區，並保持托力均勻防止因裝配間隙誤差或焊接規范變化而引起漏渣，鐵水下淌及焊穿現象，達到理想的熔深度和光潔度。
  5. Unlike oil pumps for traditional industries, our dry pumps are specified for the use of semiconductor companies. the rotor of vacuum space is not sealed with oil, but with the application of the minute clearance and high - speed rotation. therefore, a special demand is laid on the precision manufacture techniques, assembly procedures and profile design of roots rotor

    以乾式真空幫浦為例，在2001年2月第一臺賣出去以來，已賣出數百臺，本乾式真空幫浦等級屬於半導體廠專用乾式真空幫浦，不同於傳統產業使用的油式真空幫浦，旋轉轉子真空腔體內不用油去密封，而是用微小的間隙配合高速旋轉的轉子進行密封，因此特別講究精密加工技術精密組裝技術魯氏轉子線型設計。
  6. The system possesses dynamic range of scores of millimeters and focusing time of five seconds and repeatability of seven microns and measurement precision of microns level

    聚焦范圍可達幾十毫米，聚焦時間為5秒鐘，重復精度為7 。裝配間隙寬度測量的精度為微米級。
  7. This paper presents a type of image measurement and analysis system based on ccd plane array camera and general lens that can accomplish auto - focusing and collecting image and measuring and analyzing on - line assembly - gap of columned work - piece

    本論文在一般光學鏡頭的基礎上實現了一種基於面陣ccd攝像機的圖象測量及分析系統。該系統能夠實現自動對焦採集圖象和在線對回轉體工件裝配間隙進行測量分析的任務。
  8. The paper also analyzes synthetically the effects of some smooth filters prior to image segmentation and indicates that gaussian lowpass filter, a alterable scale filter, is a good choice to establish a balance between the reservation of image details and removal of noise. on the basis of current investigation of actuality and trend of image segmentation at home and abroad, the paper adopts marr operator, called by optimal edge detection to improve greatly efficiency of image segmentation and edge abstract. the sparse edge

    論文在分析當前圖象分割的現狀和趨勢的基礎上，採用被稱為最佳邊緣檢測運算元的marr演算法，使圖象分割和邊緣提取的準確性得到了很大的提高；利用人機交互輔助的方法來搜索已經檢出的稀疏邊緣點，並用最小二乘法擬合這些邊緣點，使裝配間隙寬度的測量的精度和準確性得到了極大的保證。
  9. 7. assemble inserts and cones respectively, and prepare for calculating 3d engaging distance of tri - cone rock bit

    對牙輪和牙齒分別進行了裝配，為三維嚙合間隙計算做了充分準備。
  10. In order to solving engineering problem of the hsmv - gap sensor, this paper investigates the temperature drift, communication interface and fault location technique during the course of assembly and maintenance

    圍繞高速磁懸浮列車的間隙傳感器工程化問題，本文主要研究了溫度漂移、通訊介面以及裝配維護過程中遇到的故障定位等技術。
分享友人
分享到 Line

分享到臉書