規柄 的英文怎麼說
中文拼音 [guībǐng]
規柄
英文
stem-
Based on the field investigations and laboratory examinations, a study of the population of the epiphytic dolichomitriopsis diversformis ( mitt. ) nog. in fanjing mountain reveals that its habitats are different among different host trees, but that there lies the common habitat characteristics of not more than 2m height from the bottoms of host trees trunks, less light, high relative humidity, slow wind speed, slow evaporation speed and long time of remaining humid in middle - lower tree bark ; that it is one dioecious moss species, the morphology is remarkably different between its perichaetium and perigonium, the number of its perichaetia is much more than that of its perigonia, its perigonium is difficult to find out, its sporophyte is upright, its seta is long and thin, its capsule is regular long oval and its calyptra is cucullate
摘要通過野外調查和室內觀測對貴州省梵凈山樹附生尖葉擬船葉蘚種群的研究表明,其生境因其所附生的樹種不同而有所不同,但具有共同特點:附生在樹干下部距地面2m高的范圍之內,光照弱、濕度大、風速小、蒸發量小、中下部樹皮保持濕潤的持續時間長;其為雌雄異株蘚種,雌、雄器苞形態差異明顯,雌器苞數量多,雄器苞數量少並且難于發現,孢子體直立,蒴柄細長,孢蒴規則長卵形,蒴帽兜形。Specification for table cutlery with non - metallic handles
非金屬手柄餐桌用刀叉餐具規范Specification for firefighters ' axes with glass fibre shafts
有玻璃纖維柄套的消防釜規范Morse taper shank twist drills with oversize shank
超大規格莫氏錐柄麻花鉆Pickaxe handles ; gauges
手鎬柄.量規Leaves 1 - 2 - ternate or pinnate, ovate - triangular or triangular - ovate, 6 - 10 cm long, 2. 5 - 4 cm wide, margin irregular coarsely toothed ; petioles c. 10 cm long, sheathed
葉1至2回三出式分裂或羽狀深裂,卵狀三角形或三角狀卵形,長6 - 10厘米,寬2 . 5 - 4厘米,邊緣具不規則粗鋸齒;葉柄長約10厘米,具鞘。Reamers ; technical specifications for reamers with shaft
鉸刀.帶柄鉸刀的技術規范Specification for staple, handgrab, handle, and stirrup rung
U型手柄抓具和階梯腳扣的規范Electromechanical components for electronic equipments. sectional specification. lever or toggle switches
電子設備用機電元件.分規范.手柄開關或扳鈕開關In the distributed caa and simulation system, an example of slider - crank mechanism is given. the example use planar multibody dynamic method to analysis the movement rule of slider - crank system under gravity and moment and demonstrate the multibody systems dynamic analysis method
基於實現的分散式計算機輔助分析與模擬系統,本文以曲柄滑塊為例,利用平面多體動力學通用模型分析了在受到重力和轉動力矩的情況下曲柄滑塊的運動規律。Morse taper gauges ; taper plug gauges for taper sockets with drift slot
莫氏錐度量規.第1部分:帶退柄孔錐套用錐度塞規Metric taper gauges ; taper plug gauges for taper sockets with drift slot
公制錐度量規.第1部分:帶退柄孔錐套用錐度量規In order to provide the scientific basis for the good agricultural practice ( gap ) of sichuan bai zhi, rapd was firstly used to analyze the genetic polymorphism of different type from sichuan bai zhi and hangzhou bai zhi. the result showed that different color of petiole has not obvious relationship to whether to bolt or not and different localities have more influences on genetic diversity than different color of petiole
為配合川白芷生產質量管理規范化( gap )研究,本文首次採用rapd技術對川白芷生長過程中不同形態的四個類群及杭白芷進行基因組dna多態性分析,認為川白芷葉柄顏色的不同與是否抽薹無明顯的相關性,而產地的差異對遺傳變異的影響大於因其葉柄顏色不同所造成的影響。7 24 tapers for tool skanks for manual changing
人工換刀用工具柄的7 24規格的錐銷Specification for short - range short - stem thermometers
小量程短柄溫度計規范Basing on the requirement of the project supported by chongqing science and technology committee, the study and development on original non - frictional and sequential operation ' s stepless speed regulator, the author has made some analysis to the physical principle and speed adjustment principle. in addition, as the main part of stepless speed regulators, the transformer was more concerned in the study. after probing the creation of its structure principle, this paper reveals its structure and dynamics rule, and creates a dynamics model and synthesis model of transformer
根據重慶市科委技術攻關項目《新型非摩擦式連續作用機械無級變速器的研製與開發》的要求,對該無級變速器的工作原理、調速原理及工作性能進行分析,並著重對無級變速器的核心部件轉換器進行分析,對其結構原理創新進行深入的探討,揭示了其結構及運動學的實質;建立了轉換器的運動學模型和綜合模型;對以轉換器這類以連桿作為輸出構件的曲柄搖桿機構的運動規律及其影響因素,首次進行了較深入、系統的分析研究,得出了一系列以連桿作為輸出構件的曲柄搖桿機構的運動規律。Specification for hook spanners, peg spanners, coupling wrenches and the related slots, holes and horns
鉤形扳手銷子扳手連接扳手和相關的槽孔和柄臂規范Chain saws - specification for strength of handles
鏈鋸.第9部分:手柄的強度規范Laryngoscopic fittings - part 1 : conventional hook - on type handle - blade fittings
喉鏡連接件.第1部分:常規掛鉤型手柄-窺視片接頭Specification for dimensions of driving tenons and sockets for parallel shank drills and machine reamers
直柄鉆頭及鉸刀用轉動榫及套筒尺寸規范分享友人