角位移誤差 的英文怎麼說

中文拼音 [jiǎowèiyíwùchā]
角位移誤差 英文
angular travel error
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 移 : Ⅰ動詞1. （移動） move; remove; shift 2. （改變; 變動） change; alter Ⅱ名詞（姓氏） a surname
  • 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 誤差 : error
  1. The research result indicated : for the strip primary mirror discussed in this article, the hexagon light - weighted cell has the best structural rigidity quality, the square cell is a little worse, the triangle cell is the worst ; there is an optimum on primary mirror thickness ; on condition of 1g gravity load combining with 4 centigrade uniform temperature rising, the thinner and higher of the flexible support reed, the better of the primary mirror surface figure. the decision of the structural parameters of the flexible support reed must take static rigidity, dynamic rigidity, static strength and dynamic strength of primary mirror assembly into account

    研究結果表明：對于本文的長圓形主鏡，採用正六邊形輕量化孔，鏡體結構剛性品質最好，正方形次之，正三角形最差；主鏡鏡體厚度存在最佳值；主鏡組件在1g重力、均勻溫升4共同作用的工況下，主鏡柔性支撐簧片厚度越小、高度越高，主鏡綜合面形誤差（ p - v值）越小，但同時主鏡組件的剛體位移增大、固有頻率下降，因此柔性支承結構參數的確定要綜合考慮主鏡的綜合面形誤差和主鏡組件靜態剛度、動態剛度、靜態強度和動態強度等因素。
  2. Beam deflection produces boresight error ( bse ) which is defined as angle shift between viewing direction and true direction. boresight error slope ( bses ) is defined as the ratio of angle shift to the tracing angle of the antenna

    波束偏移的主要後果是產生瞄準誤差，使目標的視在位置與真實位置有一個角度差，這個角度差就是天線罩的瞄準誤差。
  3. Verification regulation of angular displacement transmission chain error tester

    角位移傳動鏈誤差檢查儀檢定規程
  4. Abstract : the attitude error performance of electrostatic gyro should be understood and the relevant error equations must be set up in order to ensure the navigation precision of esgm. the relation between the navigation errors and the attitude errors of gyro was derived by use of spherical triangle. the simulation results show that the temporal performances of the longitudinal and distance errors which come from the initial alignment errors are periodically variational. they also show that the longitudinal and distance errors resulted from gyro drifts are not convergent in time. thus, the effects of initial alignment errors and gyro drifts can not be neglected and must be estimated and compensated

    文摘:為了保證靜電監控器的導航定位精度，需要了解靜電陀螺的姿態誤差特性，建立相應的誤差方程.本文採用球面三角形原理推導了導航定位誤差與陀螺姿態誤差的關系式.模擬結果表明，由初始定向誤差引起的經度誤差和距離誤差的時間特性是周期變化的；由陀螺漂移引起的經度誤差和距離誤差是隨時間發散的.因此，初始定向誤差和陀螺漂移的影響不能忽略，必須對其進行估計和補償
  5. The first boundary error has to be weighted by rotations and second by displacements.

    第一個邊界誤差要用轉角來加權，而第二個則用位移來加權。
  6. The position errors are measured by two dimension single - frequency laser interferometer, the pitch and yaw errors are tested using phase shifting interferometer with a resolution of 0. 1nm, the linearity along motion axis is investigated by autocollimator with 0. 01 " uncertainty

    利用單頻激光干涉儀測試其運動定位誤差特性，相位偏移干涉法測試運動轉角誤差，光電自準儀測試其運動偏擺誤差。
  7. Four groups ’ measurement data are given based on built system, and the results and the error analysis of measurement range of 1. 5, angle step of 0. 06 is discussed in detail. a list table of fitting curve and angular displacement is given as well

    利用建立的測量系統給出了四組測量數據，詳細討論了測角范圍為1 . 5 、角度遞增0 . 06的測量結果與誤差，並給出標定擬合直線與角位移的查找表。
  8. Stepper motor is a kind of electromechanical component that is driven in step angle or line displacement by electric pulse signal. because of having the advantage of easy open - loop control and no accumulating error, stepper motor is being applied widely in many fields

    步進電機是一種將電脈沖信號轉換成相應的角位移或線位移的機電元件，具有易於開環控制、無積累誤差等優點，在眾多領域獲得了廣泛的應用。
  9. The results indicate that : with sa, the position precision of the integrated system, whose gyro drifting is 50 degree / hour and whose accelerator offset is 0. 001g, is 60 meters, its velocity precision is about 1. 75m / s out and its attitude angle precision is about 0. 25 degree. without sa, the position precision is about 20 meters, its velocity precision is about 0. 5m / s and its attitude angle precision is about 0. 1 degree. when the signal of gps is lost, the growing rate of the integrated system error is much lower than that of sins system

    模擬結果表明：對于陀螺漂移為50度/小時、加速度計零偏為0 . 001g的組合系統，在有sa的情況下，位置精度大約為60米，速度精度大約為1 . 75米/秒，姿態角精度大約為0 . 25度；在無sa的情況下，位置精度大約為20米，速度精度大約為0 . 5米/秒，姿態角精度大約為0 . 1度；在gps信號丟失時，系統誤差的增長速度比純sins系統明顯減緩。
  10. Bearing capacity and displacement are two main problems in the application of geotechnical engineering. based on a series of pull - out tests using three kinds of paper and a sort of window screening as geogrid, twenty - seven in limit and several in working - stress geogrid - reinforced slope model tests designed through orthogonal principle have been conducted to have obtained the relationship between the bearing capacity and four factors ( i. e. reinforcement, angle of reinforced slope, the designed - length of reinforcement and the distance between layers of reinforcement ). the law of slope lateral ( horizontal ) displacement versus to the height of slope vary with external - load was derived from the model test data, and the main factor affecting the lateral and vertical displacement of geogrid - reinforced slope was obtained through analysis

    承載力（強度）和變形是巖土工程應用領域的兩大主要問題，本文以紙和窗紗布模擬加筋土邊坡的土工格柵，在一系列拉拔試驗的基礎上，以正交設計理論分別安排27個極限應力狀態和若干個工作應力狀態加筋土邊坡模型試驗，並以模型試驗獲得的數據為依據，採用誤差、極差及回歸分析方法，探討了加筋土邊坡承載力與筋類、筋長、層間距、坡角4因素的相關關系，獲得了在外荷載作用下加筋土邊坡的側向位移隨坡高的變化規律（並進行了定性解釋）和坡頂的豎向位移特性，並分析其主要控制因素。
  11. Because the ins error equation is unstable, some initial states error will cause error floating and error accumulating, if the filter observations were only position error, kalman filter will converge very slowly, and some states error ( such as yaw error ) will be great. since the milemeter altimeter and piloting could only output position information, this paper put forward a method, firstly estimateing states and then kalman filtering, to improve filtering effect. simulation proved that this method could effectively reduce the system states error, quicken filtering convergence and improve filtering precision

    由於慣導系統（ lsins ）的誤差方程是發散的，某些初始狀態的誤差會引起誤差的漂移和積累，當觀測量只有位置誤差時，卡爾曼濾波的收斂速度很慢，某些狀態（如方位角）誤差很大，而以上除慣導外的其它導航傳感器直接提供的只是位置信息，為了改善濾波器性能，本文根據里程計等傳感器的特點，提出了首先對狀態做出估計，然後在狀態估計的基礎上，進行卡爾曼濾波的方法。
  12. The mechanisms and conditions for the mechanisms to adjust itself were analyzed in detail. an accurate method of analyzing for the properties of the mechanisms without overconstraints was given for the first time, we obtained the equations of self - adjusting displacement in the cylindrical pair, the allowable kinematic - pair - axis errors which enable the mechanisms realize function of self - adjustment, and the most rational arrangements of kinematic pairs for the three common four - bar mechanisms. the results of analysis show that the influences of the errors of crank - pin on the self - adjusting properties of the mechanisms are bigger than that of the other pairs

    （ 3 ）詳細分析了無過約束機構能夠實現自調的機理及機構能夠實現自調的條件，首次提出了無過約束機構自調性分析的一種精確方法，得到機構自調時圓柱副中的自調位移規律和機構能夠實現自調的運動副允許誤差角以及三種常用平面四桿機構的自調結構的最適宜的運動副配置方式。
  13. The measuring system to measure the dimensional rotation errors of the namcs is configured. the principium experiment verified this method. 3

    將相位偏移干涉測量技術應用於測量與校準系統運動轉角誤差測量，初步試驗驗證了該方法的可行性。
分享友人
分享到 Line

分享到臉書