角焊縫角度 的英文怎麼說

中文拼音 [jiǎohànféngjiǎodù]
角焊縫角度 英文
fillet angle
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 縫 : 縫名詞1. （接合處） seam 2. （縫隙） crack; crevice; fissure; slit
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 角度 : 1. [數學] （角的大小） angle; the degree [size] of angle 2. （看事情的出發點） point of view; angle
  1. All the size of fillet welds k are the thickness of the wall except those marked

    未注焊縫焊角高度k均為焊件中薄壁的厚度。
  2. Effective length of fillet weld

    角焊縫有效計算長度48
  3. Effective thickness of fillet weld

    角焊縫有效厚度48
  4. Sonic new ideas and views were proposed, such as regulation on general welding procedure qualification and its method of application, welding procedure qualification between heat exchange tube and tube sheet assessmented by the thickness of fillet weld, and so on

    本文還首次提出一些新思路、新觀點，如母材、焊材分類細則以及標準以外材料分類要有分類報告佐證；通用的焊接工藝評定規定及使用方法；換熱管與管板的焊接工藝評定是評定角焊縫厚度；氣瓶焊接工藝評定是兩個類型評定的結合，也可以分別評定。
  5. This article describes a way of special ultrasonic system which monitors thermal stress in seamless welded rails. this monitoring system is a non destructive testing system, which adopts avr mcu and high - precise time chip processing as the core of it, and adopts the critically refracted longitudinal wave as the object of measuring. my studying focuses on the theory of the monitoring system, which will be listed in this arctile : according to the snell theory, the theory of motivating of critically refracted longitudinal wave is described in details, and the finite element software is used to emulate the propagating course. the formulas of calculating the pts of swr are taken from the acoustoelasticity theory, and the calculating the parameters is introduced. according to assemble materials, three kinds of ways of monitoring the pts of swr using critically refracted longitudinal wave are described, which are measuring the sound - time in changeless distance, ultrasonic critical - angle refractomery and frequency spectrum, the first way of ways is used in this experiment system. the factors, which effect the monitoring system, are assaid in some degree based

    本文的研究工作重點在無縫焊接鋼軌溫度應力測量系統的理論模塊，包括根據snell原理，研究極限折射縱波的激發機理，並使用有限元軟體ansys進行模擬;根據聲彈性理論以及公式推導出計算無縫焊接鋼軌中的溫度應力的公式，並對其中參數的求解方法進行介紹;根據收集的資料，介紹了三種使用極限折射縱波測量無縫焊接鋼軌溫度應力的方法，即固定距離測量聲時法、臨界角折射法和頻譜分析法，本實驗系統使用的是第一種;根據實驗經驗以及相關資料，分析了影響極限折射縱波測量溫度應力的幾個因素，並提出了相應的解決方法;根據實驗系統的需要，獨立設計並加工出相關配套的實驗設備，包括實驗鋼塊、有機玻璃楔塊、固定件、載荷外框裝置等。
  6. Both single and double fillet welds shall be as follows unless otherwise shown on the drawing

    除非圖上另外標明，所有單、雙面貼角焊縫高度如下。
  7. Brushed stripe coating to all areas such as corners. edges, welds. small brackets, bolts, nuts. rivet - s. and interstices, before spraying application of each coat, to ensure that these areas have at least the minimum specified film thickness

    在塗抹新塗層前，應刷掉所有區域的麻紋，比如各角落、邊緣、焊接處、小托架、螺釘、螺帽、鉚釘和裂縫，保證這些區域至少達到價格的最低膜厚度。
分享友人
分享到 Line

分享到臉書