角縫紉 的英文怎麼說

中文拼音 [jiǎoféngrèn]
角縫紉 英文
angular seaming
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  • 縫 : 縫名詞1. （接合處） seam 2. （縫隙） crack; crevice; fissure; slit
  • 紉 : Ⅰ動詞1 （引線穿過針鼻兒） thread （a needle）2 （用針縫） sew; stitch3 [書面語] （搓繩; 捻線） tw...
  • 縫紉 : sewing; tailoring; stitching縫紉車間 tailoring workshop; 縫紉工 stitcher; hemmer; 縫紉活 stitchin...
  1. If you want to be a draftsman, a machinist, amolder, or a patternmaker, you ' ll need algebra and geometry and even trigonometry

    如果你想成為手工藝人、縫紉工、造型工或制模工，你需要代數和幾何，甚至三角。
  2. If you want to be a draftsman, a machinist, amolder, o r a patternmaker, you ' ll need algebra and geometry and even trigonometry

    如果你想成為手工藝人、縫紉工、造型工或制模工，你需要代數和幾何，甚至三角。
  3. The in - plane equivalent elastic modulus and tensile strength of stitched composite laminates are studied, and it ' s found that the in - plane equivalent elastic modulus decreases with the increase of stitch density, stitch thread diameter, maximal misalignment angle and the distortion width, and the range is about 5 %. the tensile strength of stitched composite laminate increases with the increase of stitch step and decreases with the stitch space. the

    研究結果表明：隨著縫紉密度、縫紉線直徑、最大纖維偏轉角和縫紉變形區寬度的增加，縫紉復合材料層合板面內等效模量逐漸降低，最大降幅一般在5 %左右；縫紉復合材料層合板的拉伸強度隨縫紉針距的增加而增大，隨縫紉行距的增加而降低，因此縫紉密度對拉伸強度的影響程度要看具體的縫紉針距和行距。
  4. The distortion of in - plane fibers is considered to be the main reason for the effect of stitching on the in - plane mechanical properties, and the fiber distortion region, the resin - rich pocket and the through - thickness reinforcement section are taken into account. the fiber misalignment angle and the inhomogeneous fiber volume fraction caused by stitching have been determined within the lamina. the elastic constants of a lamina are calculated using a micromechanical model, then the constitutive equations of the stitched composite laminates can be composed

    從縫紉孔附近纖維變形的細觀結構出發，建立的纖維彎曲模型，以面內纖維的彎曲變形作為縫紉影響層合板面內力學性能的主要原因，同時考慮了纖維變形區、厚度增強區以及樹脂富集區的影響，得到單向板內任意一點處的纖維偏轉角和纖維體積百分含量。
  5. The engineering constants around the stitch hole in the composite laminate are analyzed using the fdm. it is found that the elastic constants have distinct region character and the traces of the resin - rich pocket in different lamina are clear

    採用纖維彎曲模型分析了縫紉復合材料單層在縫紉孔附近的最大纖維偏轉角、縫紉影響區以及縫紉復合材料單層及層合板工程常數的變化，發現工程常數具有很明顯的區域性，能夠看出各層中樹脂富集區的痕跡。
  6. We can make many kinds of needles, plates, pressers, feed dogs, and also can make new parts as you need

    本廠是生產各種工業縫紉機彎針、針板、壓角、送布牙的零件廠，並可為您加工製造各種零部件。
分享友人
分享到 Line

分享到臉書