角荷載法 的英文怎麼說
中文拼音 [jiǎohézǎifǎ]
角荷載法
英文
angle loads method-
Based on extensive investigation of construction technique history of chinese ancient buildings, the structure method, structure developing history and seismic behavior of chinese ancient timber structure buildings are analyzed in several respects of the structural system and form. through a series of experiments on constituent parts of chinese ancient timber building structure, including the tests on the corbels and brackets called dougong subjected to low cyclic reversed loadings, the tests on the wooden frame using the tenon - mortise joints as connections of column and beam subjected to low cyclic reversed loadings, the tests on vibration isolation effect of friction and slippage between column footing and their socle base, and a series of shaking table tests on a chinese ancient timber structure palace building mode under artificial earthquake at serving conditions, destroyed conditions and reinforced conditions, many valuable results of structures such as moment - curvature hysteretic loops of dougong structure and tenon - mortise joints under low cyckc reversed loadings, the static function, the seismic performance, energy dissipation, vibration reduction, energy - loss mechanism, nechanicalmode and failure mode were studied. aplenty of valuable parameters of the structure system were obtained, such as the natural period of structure, vibration modes, damping ratio, factor of vibration isolation, oscillate amplitude of ineitial accebration, velocity and displacement, magnitude of slippage, and the mechanism of structure failure and collapse etc. based on these research, the complete analysis of ancient timber structure under earthquake were carried out in which including mechanism analysis method, calculating mode, strength analysis of members and joints, strengthening methods for serving damaged ancient timber structure buildings were also taken into account
依照宋代《營造法式》建造了抬梁式殿堂木結構構件及結構模型，對中國古代木結構中的典型構造如：柱腳在礎石頂面平擱簡支、柱架榫卯連接、柱高不越間之廣、側腳、生起、斗拱等的構造機理及結構功能進行了量化分析和實驗研究： （一）通過木柱石礎靜摩擦試驗，測定了柱腳與石礎古鏡面間的摩擦系數及摩擦力隨上部結構荷載變化的規律； （二）通過單柱承載力試驗，測定了古建築中木柱的受力變形特徵、破壞模式、及模型材料的變形模量、極限承載力、極限變形等參量； （三）通過柱架低周反復荷載試驗，測定了柱架的抗側移剛度、柱架恢復力特性及滯回曲線、榫卯張角剛度及其變化規律、柱架及榫卯的極限承載力和極限變形、及榫卯減振參數； （四）通過斗?低周反復荷載試驗和受壓試驗，測定了古建築木構件與木構件間摩擦系數，斗?抗側移剛度，斗?恢復力特性及滯回曲線，斗?抗壓極限承載力及受力變形規律； （五）通過抬梁式殿堂間架模型振動臺試驗，測定了殿堂木構架結構自振周期，地震反應振形、阻尼特性及阻尼比；按結構分層特點對柱腳、柱頭和斗?層上的屋蓋的地震反應採用多點同步測量，對柱根滑移、榫卯變形、斗?的變形、復位、耗能減振參數等進行了定量分析。In this thesis, studies are focused on as follows : ( 1 ) based on analyzing the general transfer - matrix, the conception of the generalized double layer soil model is proposed, and the transfer - matrix ( r ) of half - infinite elastic mass is introduce - d to the analytic expressions of stress and settlement under the uniform circular, rectangular and strip vertical loads in multi - layered soil ; ( 2 ) according to the analytic expressions of the additional stress and settlement under unifo - rm circular in multi - layered soil, rectangular and strip vertical loads, the programs are develop - ed to resolve and debugged. the results show that the programs are correct ; ( 3 ) through calculating the coefficient of additional stress on the central axis of uniform circ - ular vertical loads, under the corner point of the uniform rectangular vertical loads, and on the central axis of uniform strip vertical loads, and the settlement on the center of uniform circular vertical loads and uniform rectangular loads in double - layered soil, the characters of stress and settlement are discussed ; ( 4 ) a case, as an example, is studied with different calculation methods, such as traditional theory, fem. the results obtained are compared
本文在已有研究成果的基礎上進一步開展了以下幾方面的研究： （ 1 ）在對層狀地基傳遞矩陣法中的總傳遞矩陣分析的基礎上，提出了廣義雙層地基模型的概念，並把半無限體的傳遞矩陣r引入到多層地基在圓形垂直均布荷載、矩形垂直均布荷載及條形垂直均布荷載作用下附加應力與沉降的解析式中； （ 2 ）根據多層地基在圓形荷載、矩形垂直均布荷載及條形垂直均布荷載作用下附加應力與沉降的解析式，編制了程序，調試通過並驗證了其正確性； （ 3 ）通過對雙層地基圓形垂直均布荷載中心軸線上的附加應力系數和荷載中心沉降，矩形垂直均布荷載角點下的附加應力系數和荷載角點沉降及條形垂直均布荷載中心軸線上的附加應力系數進行的計算，探討了雙層地基中的附加應力與沉降特性； （ 4 ）應用本文的層狀地基體系理論對一個工程實例進行了計算分析，並與傳統的計算方法的計算結果和有限單元方法的計算結果進行了對比分析，結果表明利用層狀地基理論計算更能反映地基中附加應力分佈的實際情況。This paper uses for reference with an example of frame - shear wall structure and studies the conceptual design and method for optimizationof structural system. through establishing frame - shear wall structure unisonous differential eguation and finding a result, the side shifting curve, moment and shear force distribution curve are obtained under inverted triangle load action on the frame - shear wall structure. after analyzing and comparing, the range of best rigid characteristics for such structure has be gotten
本文結合框架-剪力墻實例，研討了結構體系的概念設計和整體優化方法。通過建立框-剪結構協同工作的微分方程及求解，得出框-剪結構在倒三角形荷載作用下的側移曲線、彎矩、剪力分佈曲線，經分析對比，得出框-剪結構最佳剛度特徵值區間。This paper focuses on the research of the stress mechanism of the ribbed shell structure in statics, dynamics and under the explosive load on the basis of the engineering practice of cave depot of single aircraft. in this paper, according to the classical shell theories, the basic differential equilibrium of the ribbed shell structure and the finite element analysis of 3d rippled plate are established, in which the function of annular ribs reinforcement bars and 3d ripped steel plates are distributed in the range of the steel, and the functions along the longitude direction of tension, bending, and torsion are neglected ; applied with dynamic analytical theory, the dynamic model of ribbed shell structure and the analytical theory model of elastic - plastic are set up ; the triangle series method is used to solve the displacement and stress under the distributed load and the concentrated load of the ribbed shell structure
本文以軍用機場地面單機掩蔽庫工程建設為工程背景，首次對內襯三維波紋鋼板混凝土拱型復合結構的受力機理進行了靜力、動力和爆炸荷載的分析研究。根據將橫肋、鋼筋及三維波紋鋼板的作用均勻分佈在殼體范圍內的情況，忽略橫肋、鋼筋及三維波紋鋼板沿殼體母線方向的抗拉、抗彎及其抗扭作用，首次推導出了內襯三維波紋鋼板混凝土殼體的微分平衡方程，建立了有限元計算模型，並採用三角函數法，求解了三維波紋鋼板混凝土拱型復合結構在分佈荷載和集中荷載作用下的位移響應和應力響應，並與普通殼體進行了比較。We research the causes of concrete cracking, develop the high performance anti - cracking additive, optimize the concrete mix and construction techniques, increase the stability of concrete volume by shrinkage compensation, enhance splitting tensile strength, and can meet demand of high workability of fresh concrete. in the study, a thorough investigation of this problem is made from all points of view, with the aid of various modern measurement & testing technology and different theories & methods in surface physical chemistry, structural chemistry, solid - state chemistry, composite materials, fracture mechanics, etc. our research results have shown that the various shrinkage of concrete cause concrete cracking in building engineering, such as autogenous shrinkage, dry shrinkage, temperature shrinkage, plastic shrinkage, carbonized shrinkage, etc
目前，解決混凝土開裂的方法是綜合的，我們調查研究了混凝土開裂的原因，開發研製了高性能抗裂外加劑，優化混凝土的設計和施工方法，並通過補償收縮達到混凝土體積穩定，提高抗裂強度，滿足混凝土拌和物高工作性能的要求。本研究採用多種測試技術，應用表面物理化學、結構化學、固體化學、復合材料學、斷裂力學等多學科的理論與方法，從不同的角度進行深入的研究和探討。通過調查研究建築工程中出現的混凝土開裂、滲漏問題，發現混凝土在非荷載作用下開裂主要是由混凝土的自收縮、乾燥收縮、溫度收縮、塑性收縮、碳化收縮等各種收縮變形引起的。This article describes a way of special ultrasonic system which monitors thermal stress in seamless welded rails. this monitoring system is a non destructive testing system, which adopts avr mcu and high - precise time chip processing as the core of it, and adopts the critically refracted longitudinal wave as the object of measuring. my studying focuses on the theory of the monitoring system, which will be listed in this arctile : according to the snell theory, the theory of motivating of critically refracted longitudinal wave is described in details, and the finite element software is used to emulate the propagating course. the formulas of calculating the pts of swr are taken from the acoustoelasticity theory, and the calculating the parameters is introduced. according to assemble materials, three kinds of ways of monitoring the pts of swr using critically refracted longitudinal wave are described, which are measuring the sound - time in changeless distance, ultrasonic critical - angle refractomery and frequency spectrum, the first way of ways is used in this experiment system. the factors, which effect the monitoring system, are assaid in some degree based
本文的研究工作重點在無縫焊接鋼軌溫度應力測量系統的理論模塊，包括根據snell原理，研究極限折射縱波的激發機理，並使用有限元軟體ansys進行模擬;根據聲彈性理論以及公式推導出計算無縫焊接鋼軌中的溫度應力的公式，並對其中參數的求解方法進行介紹;根據收集的資料，介紹了三種使用極限折射縱波測量無縫焊接鋼軌溫度應力的方法，即固定距離測量聲時法、臨界角折射法和頻譜分析法，本實驗系統使用的是第一種;根據實驗經驗以及相關資料，分析了影響極限折射縱波測量溫度應力的幾個因素，並提出了相應的解決方法;根據實驗系統的需要，獨立設計並加工出相關配套的實驗設備，包括實驗鋼塊、有機玻璃楔塊、固定件、載荷外框裝置等。The retaining wall reclining on the slight slope built on soft foundation is usually used in protecting the shore of river, the contradiction between the lack of impartiality in stress of the base and the small stress allowed by the foundation as well as the lack of stabilization of the breast wall is a hard nut to crack in the engineering. in the paper, a tenon - base is added under the base of the retaining wall, on the study of the choice of the parameters and formulas used in calculation and the research of theory used in calculation, method used to deal with the load, etc, the writer gives a way to crack the nut mentioned above paragraphs and presents a qualitative and quantitative analysis about them, such as the equivalent inner friction - angle ( d ) and the passive press of the clay ( ep ), etc. in the end of the paper, using modern optimization method, a design of the retaining wall reclining on the slight slope built on soft foundation is done, the result is economical, and accords with the fact
軟基上的仰斜式擋土墻在水利工程河道護岸中經常遇到，仰斜式擋土墻基底偏心應力較大和軟基土地基容許承載力偏小的矛盾以及擋土墻抗滑穩定不足是工程中難以解決的難題。本文在對仰斜式擋土墻設計中有關計算參數的選擇、公式的選用應該注意的問題進行了研究，對河道護岸軟基礎上的仰斜式擋土墻採用凸榫基礎處理的方法，就其計算理論、設計驗算中各荷載的具體處理方法進行了較為細致的研究，提出了解決軟基礎上的水工仰斜式擋土墻難以解決的難題的方法，並對有水情況下粘土等效內摩擦角_ d 、凸榫被動土壓力e _ p等在計算中的取值提出了定性和定量的分析。最後利用現代優化方法對軟基礎上的水工仰斜式擋土墻進行了結構優化設計，得出了符合實際的結果，與其它重力式擋土墻形式進行比較，取得了明顯的經濟效益。Taking the bending stiffness, cable sag and cable inclination into consideration, the space vibration control of the cables using the visco - elastic dampers in cable - stayed bridges is investigated by joining the center difference method and the state space strategy. both the maximum modal damping ration and the optimal damper size are obtained, then the practical suggestions are proposed for the design of the dampers. the space nonlinear vibration equations of the cable - damper system are derived, and a new hybrid method for solving the cable - damper system is presented by combing the newmark method and pseudo - force technology
綜合考慮了拉索抗彎剛度、垂度的影響，研究了粘彈性阻尼器對斜拉橋拉索的空間振動控制，聯合中心差分方法及狀態空間法，得出了拉索麵內、外振動各階模態可能達到的最大阻尼比及相應的最優阻尼器系數，並對斜拉橋拉索的阻尼器設計提出了參考建議：考慮拉索抗彎剛度、垂度及幾何非線性，導出了索-阻尼器系統的空間振動非線性方程組，結合newmark方法及偽力（ pseudo - force ）方法，創新地提出了求解非線性方程組的雜交方法，根據拉索-阻尼器系統的阻尼特性，在各種荷載作用下，對索-阻尼器系統的非線性瞬態振動響應進行了研究，從系統響應的角度更加直接地驗證了阻尼器的控制效果。Firstly, by the method of laplace transform, one dimensional consolidation of one - layer gibson soils under time - depend loading is studied and the analytical solutions in frequency domain are obtained. on the basis of the solutions obtained and the computation through programming, the influence of some parameters and loading conditions on the consolidation behavior under trapezoidal, triangular and rectangular cyclic loading, is investigated. secondly, one - dimensional consolidation of one - layered gibson soils with semi - pervious boundaries is studied in this paper, and according to numerical examples, some characters of consolidation such as the effective stress and settlement in the soils under arbitrary loading are found
首先運用了laplase變換獲得了單層gibson地基（壓縮模量隨深度線性增加的地基）在任意荷載下頻域內的一維固結解析解，通過laplace逆變換，基於以上解答用數值方法編製程序對單層地基在常見荷載（驟加荷載、緩加荷載、矩形波載、三角形波載）作用下的一維固結性狀進行了討論，並與傳統的太沙基理論進行了比較。Then, by analyzing the extensive test data of load - displacement and bear - curvature, we can conclude that the crack resistance, bearing capacity of normal section and short - dated rigidity will be improved a lot when the strength of concrete is not so low
然後，通過對各組試件的荷載-撓度曲線的進一步分析表明：對于混凝土強度等級高於c15的鋼筋混凝土梁，採用這種粘角鋼加固法能有效提高鋼筋混凝土梁的正截面承載力和短期剛度。In the paper, the method of equivalent stress is adopted to confirm the outside force of the truss model, and the factor of the angle of inclined column is considered. a design method of the wall was suggested
採用等效應力法確定了桁架模型的外力，即薄壁柱傳來的荷載，其中考慮了斜柱的傾角以及反映薄壁柱與轉換梁共同作用的薄壁柱端部塑性發展系數的影響。Steel structure of light - weight buildings with gabled frames is a widely used steel structural style in china at present. this paper starts with the deficiency of the specificaion in calculating the effective length factors of gable portal frames. when the gable portal frame subjected to the vertical uniform loading, it conducts the arch effect ? 1. rafter axial force is large when the slope of rafter is big
門式剛架輕型房屋鋼結構體系是目前廣泛應用的一種結構形式，本文從規范中門式剛架柱的計算長度系數取值的不足出發，針對山形門式剛架在豎向均布荷載作用下產生的拱效應? ? 1 、斜梁傾角較大時產生較大的梁內軸力; 2 、產生跨變效應; 3 、高跨比較小的山形門式剛架會發生躍越失穩，採用整體分析的方法對山形門式剛架的穩定進行了分析。Multi - span plastic greenhouse structure design theory has been studied systemic which include design loads, design methods and system optimization designs aimed at the situations above - mentioned, meanwhile, theory analysis and designs have been completed for series east - china multi - span plastic greenhouses in accordance with the local climate characteristic. some elementary conclusions are summed up : ( 1 ) in the aspect of multi - span plastic greenhouse structural design loads researches, based on the contrast analysis of loads provided in foreign and chinese standards, analysis and discussion are mentioned about the definition loads, the estimation and load cases for multi - span plastic greenhouse structural design in details, some conclusions are summed up first : i, wind load : under the present conditions, it is unnecessary to
得到一些初步的結論： （ 1 ）在連棟塑料溫室結構設計荷載研究方面，從分析比較國外關于溫室建築及我國工業與民用建築設計荷載規范的角度出發，針對連棟塑料溫室結構設計中的荷載定義方法、計算取值、荷載組合等進行了較深入的探討和分析，首次得到以下結論： 、風荷載：在現有條件下，考慮風壓高度變化系數、陣風作用因子和風荷載體型系數，按中國建築結構荷載規范（ cbj9 ? 87 ）計算風荷載是可以的，不必進行重現期博士學位論文摘要修正。Bearing capacity and displacement are two main problems in the application of geotechnical engineering. based on a series of pull - out tests using three kinds of paper and a sort of window screening as geogrid, twenty - seven in limit and several in working - stress geogrid - reinforced slope model tests designed through orthogonal principle have been conducted to have obtained the relationship between the bearing capacity and four factors ( i. e. reinforcement, angle of reinforced slope, the designed - length of reinforcement and the distance between layers of reinforcement ). the law of slope lateral ( horizontal ) displacement versus to the height of slope vary with external - load was derived from the model test data, and the main factor affecting the lateral and vertical displacement of geogrid - reinforced slope was obtained through analysis
承載力（強度）和變形是巖土工程應用領域的兩大主要問題，本文以紙和窗紗布模擬加筋土邊坡的土工格柵，在一系列拉拔試驗的基礎上，以正交設計理論分別安排27個極限應力狀態和若干個工作應力狀態加筋土邊坡模型試驗，並以模型試驗獲得的數據為依據，採用誤差、極差及回歸分析方法，探討了加筋土邊坡承載力與筋類、筋長、層間距、坡角4因素的相關關系，獲得了在外荷載作用下加筋土邊坡的側向位移隨坡高的變化規律（並進行了定性解釋）和坡頂的豎向位移特性，並分析其主要控制因素。Under the horizontal earthquake action and wind force, aim at " the pure frame structure with rectangle columns ", " the pure frame structure with special - shaped columns ", " the frame - truss structure with special - shaped columns " and " frame - shear wall structure with special - shaped columns ", earthquake action analysis was done by the spacial finite element method through the changes structural parameter. analyzing systematically " structure vibration mode ", " vibration period ", " structure lateral rigidity ", " seismic action force ", " seismic response force ", " floor seismic shear force ", " lateral horizontal displacement of structure " and " members internal force ". results indicate : ( 1 ) based on equal area, the special - shaped columns replaced the rectangle columns, the structural lateral rigidity enlarges, the lateral displacement minishes obviously, the earthquake response increase slightly, the biggest increasing amount of frame columns axis - compress ratio is smaller than 0. 08. the whole aseismic performance of structure has improved ; ( 2 ) when the section ' s length and section ' s thickness ratio of special - shaped columns is smaller than 3. 6, the structure benefits to resist seismic action ; ( 3 ) the angle of horizontal seismic action with the whole coordinate is 0 degree, structure earthquake response is bigger, belonging to a control factor of structure aseismic design ; ( 4 ) the frame - truss structure with special - shaped columns and the " a " - brace has the biggest lateral rigidity ; ( 5 ) the frame - shear wall structure with special - shaped columns have bigger lateral rigidity and smaller displacement, members internal force enlarged just rightly, have much superiority of resisting seismic action ; ( 6 ) in the higher seismic fortification criterion region ( 8 degree of seismic fortification intensity ), aseismic disadvantageous building site ( iii type site ), adopting special - shaped columns structure system, should reduce possibly the building ' s self - weight in order to reduce the earthquake response ; ( 7 ) the response spectrum method of computing seismic response and the time - history analysis method have similar analysis result
西安理工大學碩士學位論文在水平地震作用下，並考慮風荷載組合，分別對「矩形柱純框架結構」 、 「異型柱純框架結構」 、 「異型柱框一析架結構」及「異型柱框-剪結構」等四種結構體系，通過改變結構參數，運用空間有限元方法，進行地震作用計算。系統地分析研究「結構振型」 、 「振動周期」 、 「結構側向剛度」 、 「結構地震反應力」 、 「樓層地震剪力」 、 「結構側向位移」 、 「層間位移角」 ，以及「構件內力」 。結果表明:在等面積原則下，異型柱代換矩形柱后，結構剛度增大，側向位移明顯減小，地震反應力略有增加，框架柱軸壓比最大增幅小於8 % ，結構整體抗震性能有所提高;當異型柱肢長肢厚比小於等於3 . 6時，結構有利於抗震;水平地震作用力與整體坐標夾角為0度時，結構地震作用效應較大，屬結構設計的控制因素之一;異型柱框一析架結構採用「人」字斜撐，側向剛度大於「八」字斜撐和「人一八」字混合斜撐;異型柱框一剪結構側向剛度大、位移小，構件內力增大適中，是一種抗震性能優越的結構體系:在抗震設防烈度較高地區（ 8度）和抗震不利的建築場地（ m類場地） ，採用異型柱結構體系時，應盡可能減輕結構自重，降低地震作用力;分別採用「振型分解反應譜」法和「時程分析」法進行地震作用計算，兩種方法所得結果基本一致。The mechanic character, destroying pattern, the ductile and dissipation energy capacity of this composite structure under the earthquake have been clarified. the stiffness degradation, natural frequency, damping ratio of this structural system with the development of intensity of earthquake have also been investigated. with consideration of the top displacement, drift of story and micro - strain of longitude steel bars, the equivalent shell wall method has been presented in order to simplify the design of such type structure
通過試驗，掌握了該結構體系在水平地震荷載作用下的受力特點、變形與耗能性能、結構的破壞形態等力學指標：得到了結構在不同地震烈度條件下的剛度變化、自振頻率、阻尼比等動力特性；綜合結構的頂點位移、層間轉角以及鋼筋的微應變，提出了適合於該結構體系簡化設計的「等效剪力墻法」 。Proceeding from the structural mechanics, this paper used method which is widely used in structure optimization of industry and civil building to the structure optimization of dairy housing. it was the first time to choose the structural parameters of dairy housing according to the feeding technology, discussed the load values and combinations, optimized the structural materials
本文從結構力學的角度出發，把目前廣泛用於工業與民用建築結構優化的方法用於成乳牛舍的結構優化，首次從飼養工藝的角度對牛舍的建築參數進行了優選，對荷載的取值及組合進行了討論，對結構用材進行了優選。The works in detail are as follows : 1. base on the essential solution for a complete elastic half space impacted by antiplane line source loading at horizontal surface, the essential solution of displacement field for an elastic half space with an arbitrary - shape - canyon impacted by antiplane harmonic line source loading at horizontal surface is constructed by using the method of complex function and conformal mapping
從完整的彈性半空間表面承受線源荷載作用問題的基本解出發，用復變函數的保角映射方法獲得含有任意形凹陷的彈性半空間在其水平面上任意一點承受時間諧和的反平面線源荷載作用時位移場的解答，即本文的green函數。Based on experimental research and theoretical analysis, investigations on the new type of joint are made systematically, the main contents and results include the following items. 1 four specimens of new joints between cfrt columns and steel beams are designed. by low - cyclic reversed load test, skeleton curves of new joints and shearing deformation in joint core area are studied, the influence of parameters, such as concrete cores, length of stiffener, and relative dimensions of column and beam, is discussed
本文在分析現有節點方案特點的基礎上，提出了角鋼加勁式節點方案，並採用試驗和理論分析相結合的方法，對這種新型節點進行了系統研究，主要研究內容與成果如下： （一）設計了4個新型方鋼管混凝土柱?鋼梁節點的試件，通過對新型節點的低周反復荷載試驗，研究了新型節點的骨架曲線和節點核心區剪切變形等，探討了內填混凝土、加勁肋長度和樑柱相對尺寸等對節點抗震性能影響。Eventually, the rehabilitated specimens were retested under low cyclic loading. the loads and displacements of the beam end as well as the steel or plate strain were measured in detail ; and furthermore, crack patterns and failure model of the specimens were also observed during the test
在對試驗結果的整理分析后，本文對比研究了加固前後以及用不同加固方法加固的試件的開裂荷載、屈服荷載和極限承載力、梁端荷載?轉角滯回曲線及其包絡線特徵、延性和耗能性能。分享友人