角鋼框 的英文怎麼說

中文拼音 [jiǎogāngkuàng]
角鋼框 英文
angle frame
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  • 鋼 : 鋼名詞（鐵和碳的合金） steel
  • 框 : 框名詞（框架; 框子） frame; case
  1. Frame columns inset the filler - wall, avoided the influence that the comer of the room columns outstanding to indoorses view and take up the using space. at the same time, this structure has some advantages as the frame structure, such as arranging neatly, comparting easily etc., deeply welcoming by inhabitant and real estates company, is a building structure system that have the vast development foreground and satisfying the request of green building ". current, the reinforced concrete special - shaped columns structu re system lacks the actual measuring data of earthquake damage and the comprehensive aseismic performance of structure system, the structure system not yet is included in the national code, needing the thorough research

    鋼筋混凝土異型柱結構體系，採用t形、 l形、十形截面柱代替傳統的矩形截面柱，以輕質材料製作的框架填充墻代替自重較大的粘土磚填充墻；框架柱隱于墻內，避免了屋角柱楞突出對室內觀瞻及佔用空間的影響，同時，又具有框架結構布置靈活、易於分隔的優點，深受住戶及房地產開發商的歡迎，是一種滿足「綠色建築」要求並具有廣闊發展前景的建築結構體系。
  2. Based on the past results, seismic behavior of r. c. frame structure with special - shaped column is studied, according to the members to the structure in sequence in this paper. the main contents are as follows aspects : first of all, aiming at the characteristics of special - shaped column, various control parameters including allowable value of drift angle, axial load ratio etc, are studied

    本文在前人研究成果的基礎之上，就鋼筋混凝土異形柱框架結構的抗震性能，按照從構件到結構的順序展開研究，主要內容如下：第一，針對異形柱的特點，對影響結構抗震性能的主要參數，如層間位移角、軸壓比等進行研究。
  3. The shear mechanism, failure mode, deformation capacity, bearing capacity and the reliability of the anchored angle steels of the wrapped steel concrete cast - in - site frame typical story exterior joints under the middle and high axial compression ratio ( n = 0. 3, 0. 5, 0. 6 ), the working performance, failure mode, and the shear capacity of top story joints under the crack moment, the hysteresis characteristic and the dissipation energy capacity of the test joints are all analysed based on the 1 / 4 model pseudo - static tests of five specimens of wrapped steel concrete cast - in - site frame exterior joints, which varied in axial compression ratio, distribution of the beam angle steels and the stirrup ratio

    基於上述分析，本次試驗通過五個外包鋼混凝土邊節點1 4比例模型的偽靜力試驗，以柱的軸壓比、梁角鋼布置形式、配箍率等為主要參數，分析外包鋼混凝土現澆框架一般層邊節點在中高軸壓比（ n = 0 . 3 、 0 . 5 、 0 . 6 ）條件下，節點的抗剪機理、破壞模式、變形能力、承載能力和角鋼錨固的可靠性；分析了頂層邊節點在張開彎矩作用下的工作性能、破壞模式和抗剪承載力；分析了試驗節點的滯回性能和耗能能力。
  4. In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented

    本文借鑒鋼框架節點構造，設計了四種類型矩形鋼管混凝土柱與鋼梁連接節點，包括常規栓焊（ wfp ）節點、翼緣全螺栓連接（ bfp ）節點、雙t板連接（ dst ）節點以及加勁端板連接（ sep ）節點，進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究，比較了不同軸壓比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵，主要結論有： 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈，沒有或略有捏攏現象，耗能能力強； 2 、軸壓比對節點滯回曲線有顯著影響，全部節點都有顯著的剛度退化； 3 、位移與轉角骨架曲線在峰值荷載後有較長的水平或下降段，具有良好的延性性能； 4 、從整體抗震性能上看，翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點，可在實際工程中加以推廣。
  5. This paper applies nonlinear finite element program bsnfem to analyze the behaviors of eccentrically braced steel frames under cyclic load. the study that comprehensive and systematic analyze the factor of links length, thickness of links flange, distance of links rib, thickness of links rib and angle of brace to be changed affect energy - dissipation capacity of d shape and k shape eccentrically braced steel frames have been some studied before. this paper fills the black in the filed factor of high - span ratio, brace stiffness and brace - to - beam connections to be changed affect energy - dissipation capacity of d shape and k shape eccentrically braced steel trames and any factor to be changed affect energy - dissipation capacity of y shape eccentrically braced steel frames

    對耗能梁段的長度、耗能梁段腹板的厚度、耗能梁段翼緣的厚度、耗能梁段加勁肋的間距、耗能梁段加勁肋的厚度、支撐的夾角等因素的改變對d形、 k形偏心支撐鋼框架耗能的影響，前人已有一些研究，本文對這些因素的影響進行了全面系統的分析，完善了理論分析的不足；而結構高跨比、支撐剛度、支撐與梁的連接形式等因素對d形、 k形偏心支撐鋼框架破壞機理的研究以及各種因素對y形偏心支撐鋼框架破壞機理的影響，則很少有人涉及，本文對此也進行了深入系統的分析，填補了這一研究空白。
  6. This article describes a way of special ultrasonic system which monitors thermal stress in seamless welded rails. this monitoring system is a non destructive testing system, which adopts avr mcu and high - precise time chip processing as the core of it, and adopts the critically refracted longitudinal wave as the object of measuring. my studying focuses on the theory of the monitoring system, which will be listed in this arctile : according to the snell theory, the theory of motivating of critically refracted longitudinal wave is described in details, and the finite element software is used to emulate the propagating course. the formulas of calculating the pts of swr are taken from the acoustoelasticity theory, and the calculating the parameters is introduced. according to assemble materials, three kinds of ways of monitoring the pts of swr using critically refracted longitudinal wave are described, which are measuring the sound - time in changeless distance, ultrasonic critical - angle refractomery and frequency spectrum, the first way of ways is used in this experiment system. the factors, which effect the monitoring system, are assaid in some degree based

    本文的研究工作重點在無縫焊接鋼軌溫度應力測量系統的理論模塊，包括根據snell原理，研究極限折射縱波的激發機理，並使用有限元軟體ansys進行模擬;根據聲彈性理論以及公式推導出計算無縫焊接鋼軌中的溫度應力的公式，並對其中參數的求解方法進行介紹;根據收集的資料，介紹了三種使用極限折射縱波測量無縫焊接鋼軌溫度應力的方法，即固定距離測量聲時法、臨界角折射法和頻譜分析法，本實驗系統使用的是第一種;根據實驗經驗以及相關資料，分析了影響極限折射縱波測量溫度應力的幾個因素，並提出了相應的解決方法;根據實驗系統的需要，獨立設計並加工出相關配套的實驗設備，包括實驗鋼塊、有機玻璃楔塊、固定件、載荷外框裝置等。
  7. The present findings of nonlinear research in frame structures, and the methods for design of second - order effect in the codes from china and other countries, were briefly introduced in this paper. the contents and methods of design and calculating about second - order effect in gb50017 - 2003 were discussed as well. a rotational displacement equation for geometric nonlinear structures was derived, and then a nonlinear finite element program for rigid frames was compiled by fortran

    本文簡要地介紹了框架結構非線性研究的現狀以及各國規范對框架二階效應的設計內容和方法；對我國《鋼結構設計規范》 gb50017 - 2003給出的考慮框架結構二階效應的方法進行了探討；推導了基於幾何非線性框架的轉角位移方程，在此理論基礎上用fortran語言編制了剛性框架二階內力分析的有限元計算程序，並用此結構分析程序對多種框架進行了一階和二階的彈性分析，討論了二階效應在框架分析中不應忽略的原因，同時分析了影響框架二階效應的因素。
  8. After these years, our company has developed a series of professional, high quality and multifunctional products. moreover we focus on after services. our products including : lift clothes rack, ground flex clothes rack, aptitude invisisble security fence, no frame glass windows, bathroom rack, in - house shelf, home cleaning stuff and so on. and we provide the peripheral product on home commodity and home security adornment, which is made of stainless steel tube, steel tube, pvc composite tube

    主要產品包括：升降衣架系列、落地伸縮衣架系列、智能隱形防護網系列、無框玻璃窗系列、浴室角架系列，室內置物架系列，家庭清潔用品系列等，並配套生產以不銹鋼管、鋼管、 pvc復合鋼管為主要材料的家居日用品及家居安全裝飾品。
  9. Through the comparative text of the four reinforced concrete frames braced with the eccentric steel, which have the same shapes, materials, dimension and the different brace form, several parameters of these frame behavior, such as side stiffness, limit load and energy consume ability, were studied. the limit state of these frames were analyzed

    本文通過對四榀具有同一外形尺寸及配筋而具有不同型式的偏心角鋼支撐的鋼筋砼框架和一榀相同尺寸及配筋的鋼筋砼框架的對比性試驗，研究了上述結構的抗側剛度、極限承載力及結構的耗能等各項指標，探討了偏心角鋼支撐鋼筋砼框架結構的受力特點，並對其極限狀態進行了理論上的分析。
  10. Based on the results, the eccentrically braced frame has the advantage of higher initial stiffness, load - bearing and energy consume ability. through the limit state analysis principle, the limit load was calculated by assuming the same destroy pattern of braced frame as that in the experiment. comparing the theory limit load with the measured, a good agreement was founded. it shows that the limit state analysis is really a practicable way analysed the reinforced concrete frame braced with eccentric steel

    應用極限分析中的極值原理對偏心角鋼支撐鋼筋砼框架進行極限分析時，首先擬定與試驗結果相一致的結構倒塌破壞模式，然後根據虛功原理建立了結構在極限狀態時極限承載力的計算公式，從所求的權限荷載的理論值與實測值的比較來看，理論計算值與試驗的實測值基本吻合，這說明利用本文擬定的結構破壞模式對偏心角鋼支撐框架結構進行極限分析是一條可行的途徑。
  11. The philosophy and methodology of performance - based seismic design ( pbsd ) has been an extensive topic discussed by earthquake engineering experts at home and abroad. in this paper, research work on displacement - based seismic design ( dbsd ) at home and abroad are systematically collected and analyzed. based on the available references of seismic behavior of frame - wall buildings, the method of dbsd of reinforced concrete frame - wall buildings is primarily put forward by taking into account the fault of methods of seismic design in current code. the main contents are as follows : the actual stiffness of frames and seismic walls at different deformation stages are determined from experimental data, and the results are adopted in the dbsd method

    本文對國內外基於位移的抗震設計研究成果進行了較系統的綜述與分析，在已有框架-剪力墻結構抗震性能研究的基礎上，針對現行抗震設計方法的不足，提出了鋼筋混凝土框架-剪力墻結構直接基於位移的抗震設計方法，並對其進行了一些研究和探索，主要內容如下：對國內外框架和剪力墻的模型試驗數據進行分析，量化了剛度退化系數與層間側移角之間的關系，並將其結果引入框架-剪力墻結構直接基於位移的抗震設計方法中。
  12. Cavity sandwich panel infill is made of paper triangle cavity material, which is a kind of low density and environmental material. it could increase lateral resistant ability of frame while decrease the weight of the structure

    空腔結構材料為一種紙基三角空腔結構材料，它是一種新型輕質節能環保型復合材料，用於填充墻鋼框架結構中既可以提高結構的抗側力性能，又可以減輕結構自重。
  13. There are still many problems remain to be solved in these aspects, such as behavior research on the lateral resistant of steel frame and connection etc. in this paper three 1 : 2 - scale steel frame specimens and eight full - scale steel frame connection specimens are tested on their behavior under cycle loading. there are six aspects as below on the problems of steel resident building researched : 1 pseudo - static force testing of eight full - scale connections, including top - seat angle connections, two web flange and top - seat connections and dog - bone connections are carried out for the first time in our country

    本文針對鋼結構住宅體系中亟待解決的若干問題，完成了三榀1 ： 2鋼框架模型和八個足尺比例的樑柱連接模型在低周往復荷載作用下的試驗，進行了以下幾個方面的深入研究： 1進行了頂底角鋼連接、帶雙腹板頂底角鋼連接等半剛性連接及狗骨式剛性連接這三種連接類型共八個原型試件的擬靜力試驗。
  14. The experimental research on seismic performance for angles beam - column connections of steel frame

    鋼框架樑柱角鋼節點連接的抗震性能試驗研究
  15. Steel frame with welding joint easily occur brittle collapse because of having a low ductility at joints then ， a semi - rigid connected steel frame has large the energy absorption capacity which can resist dynamic loads and the using steel qualities of bracing system and joints are small so adopting a semi - rigid jointed steel frame is economical and stable but for semi - rigid connections are complex and variable ， in conventional analysis and design of steel structures ， it is usually assumed that the connections between columns and beams are either rigid or pinned the analysis of steel frames adopting the assumption can simplify the procedure of analysis and design ， but cannot precisely reflect structural practical circumstance and the errors of calculating results are large ， even ， get incorrect conclusions semi - rigid connection was referred to in chinese code for design of steel structures ( 2001 ， 10 ) ， however ， it isn ’ t specified how to apply semi - rigid joints in design in fact it cannot be carry out the purpose of the paper give a calculating method that accords practical engineering and easily put into effect worthwhile it is going to promote the development of semi - rigid jointed steel frame in design and heighten structural stability in the paper ， at first some commonly employed methods for the modeling of connection behavior are introduced richard abbott function modeling of connection is adopted for extended end plate bolted connection by the 34 test data comparing to regression analysis indicate richard - abbott function modeling of connection represents an excellent fit to test data then after a semi - rigid joint behavior can be modeled as a finite stiffness rotation spring ， base on rotation and displacement equation derive the element stiffness matrixes with semi - rigid connections where the effects ofj ointed flexibility geometric non - linearity and shear forces in the connection deformations have been considered in and fixed - end forces are modified finally, a program for calculating semi - rigid with incremental - iterative method has been

    本文的目的就是為半剛性連接鋼框架的設計提供一種既符合工程實際又簡便易行的計算方法，供規范使用過程的補充、延伸或參考；同時，也將促進半剛性連接鋼框架設計技術的發展，為提高結構安全性能、節省工程成本發揮應有的作用。本文首先介紹了常見的幾種應用較為廣泛的樑柱連接彎矩轉角關系模型，在分析比較的基礎上，選用richard ? abbott函數模型作為外伸端板連接彎矩轉角關系模型，通過對34個外伸端板連接的實驗數據與回歸分析得到的參數比較可知，經回歸分析得到的此模型參數與實驗數據符合較好。然後用彈簧表徵連接點的轉動剛度，根據梁的轉角位移方程推導出半剛性連接的剛度矩陣，在單元剛度矩陣中考慮了節點柔性、幾何非線性和剪切變形的影響，並對固端力進行了修正，最後用增量迭代法編制有限元程序進行計算和分析。
  16. Then after a semi - rigid joint behavior can be modeled as a finite stiffness rotation spring, base on rotation and displacement equation derive the element stiffness matrixes with semi - rigid connections where the effects of jointed flexibility and shear forces in the connection deformations have been considered in and fixed - end forces are modified. finally, a program for calculating system reliability of semi - ridge steel frames with monte carlo method and finite element analysis has compiled for calculating and analyzing. by calculating results of several examples for steel frame in semi - rigid joints case show the change of joint stiffness and other kinds of factors affect the system

    接著本文在介紹和分析半剛性連接彎矩和轉角關系模型的基礎上，用帶有轉動剛度的彈簧表徵半剛性連接，推導出半剛性連接的剛度矩陣，對固端力進行修正，同時考慮了剪切變形的影響，編制了半剛接鋼結構平面框架的有限元程序bhpfl ，並在其基礎上編制了基於蒙特卡洛法的montecarlo - bhpfl有限元相結合的方法，進行體系可靠度的分析。
  17. Double side of concrete panel can bear and deform coincidently because angle - steel frame and steel wire confined, it ensured durable character of sandwich wall, too, due to thick of wall increasing, wall ' s stable bearing strength was improved

    雙側的混凝土面層保證了墻體的耐久性；由於角鋼邊框和拉結鋼絲對雙側混凝土面層的約束，保證了雙側墻板的協同變形和承載能力；保溫層增大了墻體厚度，提高了墻體的平面外穩定性。
  18. Though the pseudo - static test of three prototype - modal sandwich wall with angled - steel column, seismic behavior are discussed. based on the concrete nonlinear analyzing theory, this paper constructed the finite element modal by ansys program and proved the modal by test result. designed & further improved methods are presented on the conclusion of tests and calculations

    本文通過對三個角鋼邊框復合剪力墻板的原型擬靜力試驗，研究了角鋼邊框復合剪力墻的抗震性能，同時在現有混凝土非線型分析理論的基礎上，採用ansys有限元分析程序建立了墻板的有限元模型，結合試驗數據對模型進行了驗證。
  19. Structural steel has been widely used in the residential building abroad for many years, but it just begins to be adopted in the residential building since recent years. technically, steel residential building system must accord with the characteristics of residential building and the development of residential industrialization

    從技術角度來講，如何使鋼結構適應住宅建築的特點，滿足住宅產業化發展的需要，還有許多問題有待于進一步研究，如圍護墻體、抗側力體系、鋼框架樑柱連接等。
  20. By analysis, the purpose of transforming connection failure mode and controlling the position of plastic hinge has been reached by this connection construction another approach to improve ductility of structure is to utilize semi - rigid

    改善鋼框架結構延性的另一種途徑是半剛性節點的研究與利用，半剛性節點是通過角鋼和連接件的變形吸收能量達到延性的目的。
分享友人
分享到 Line

分享到臉書