觸發控制 的英文怎麼說

中文拼音 [chùfākòngzhì]
觸發控制 英文
trigger control
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 發 : 名詞（頭發） hair
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 觸發 : detonate by contact; touch off; trigger; strike
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  1. The device mainly consists of integrated phase - shift trigger unit, detection unit, amplification and impedance conversion unit, the smallest excitation limitation unit, reactive regulation unit and three - phase controlled bridge rectifier

    本裝置主要包括集成移相觸發單元、檢測單元、放大及阻抗變換單元、最小勵磁限制單元、無功調查單元和三相全控橋。
  2. This paper studies two tcsc study systems, a tcsc system based on ieee first benchmark model ( ieee fbm ) and a simplified yi - feng 500kv tcsc study system, with ssr eigenvalue analysis in the platform of psaspfmsst. it proves the funtion of tcsc to mitigate subsynchronous resonance ( ssr ). it also analyzes the influence of thyristor triggering algorithm of tcsc on ssr mitigation

    本文在psasp小干擾線性化平臺psasp msst上，對基於ieeefirstbenchmarkmodel （ ieeefbm ）的tcsc系統及簡化的伊馮500kv可控串補研究系統，進行了ssr小干擾穩定分析，驗證了tcsc對次同步諧振（ ssr ）的抑制作用，並研究了觸發演算法對tcsc抑制ssr能力的影響。
  3. The modulating signals of firing delay angle at the rectifier and firing lead angle at the inverter, and the excitation voltage are chosen to be control variables. the offset of the current of dc line and the extinction angle and the power angle of generator are chosen to be control outputs. then a nonlinear controller is designed for the system under study according to direct feedback linearization theory

    以整流側觸發延遲角的調節信號、逆變側觸發超前角的調節信號以及發電機勵磁電壓作為控制變量，以直流線路電流、逆變側關斷角以及發電機功角的偏移量作為目標輸出，用直接反饋線性化方法設計了系統的非線性控制器。
  4. At the same time the principles of triggering pulse to the three - phase thyristors is discussed, and a way using monostable multivibrator to produce the pulses has been given below. the hardware control system based on tms320f240 is designed, which includes sampling circuit, protective circuit, phase - compensated circuit and so on

    對三相晶閘管控制電抗器的觸發脈沖產生原理進行了分析，採用單穩態觸發器實現六相觸發同步；設計了以tms320f240為控制核心的硬體控制平臺，包括采樣電路、保護電路、六相觸發同步等外圍電路。
  5. Silicon controlled rectifier control output - scr zero - acrossing trigger pulse output, ac 400 v 0. 5a

    可控硅控制輸出scr過零觸發脈沖輸出
  6. The close - cycle control thyristor digit triggering circuit design

    閉環控制晶閘管數字觸發電路設計
  7. The infection control precautions necessary to preent airborne, droplet, and contact transmission are quite different and will need to be decided on and planned before a pandemic occurs

    為了避免空氣傳播、飛沫傳播和接觸傳播的感染控制的必要的警惕是不同的，而且應該在大流行爆發之前就要確定並計劃好。
  8. A data acquisition system with the following features is realized : ? transmission rate up to 100kbyte / s over usb ; ? system ' s dynamic range as high as 120 db ; ? multi - kind of trigger mode control ; ? sampling rate as high as 100 ksps ; ? 12 - bit a / d conversion accuracy ; ? 32k bytes on - board data memory ; ? the system, which was made up of large - scale electronic chips, is small, light and portable, and suitable for field use

    本設計最終實現了一個瞬態信號數據採集系統，它具有以下特點： ?採用usb介面進行高速數據傳輸，傳輸速度達100kbyte / s ； ?採用浮點a / d轉換技術，動態范圍達120db ； ?多種采樣觸發控制方式； ?最高采樣率100ksps ； ? 12位采樣精度： ? 32kb數據緩存； ?使用新型大規模電子器件，系統結構緊湊，重量輕，適合野外作業。
  9. As an experiment of basic course in electronic technology, the project is based on domination principle of digital music player and integrates with the elementary application of multiplexer, flip - flop, counter and rom, which enables students to comprehend these knowledge fully along with acquaintance of technical application and promotes systematic understanding of basic notions, course content and advances the transformation from knowledge to ability

    作為數字電子技術基礎課程的實驗內容，該方案設計以數字音樂播放的控制原理為切入點，結合了數據選擇器、觸發器、計數器和只讀存儲器的基本應用，使學生在充分理解這些知識點的同時了解一些工程應用背景，以形成對課程內容、基礎概念的系統認識，促進知識向能力的轉化。
  10. The control circuit of digitalized soft - starter with the three - phase ac voltage regulating was designed. the digital phase shifting trigger based on the 80c196kc mcs and gal16v8 programmable device was developed. the control method for digital phase shifting trigger was given and its principle of operation and designing was discussed

    設計了三相晶閘管交流調壓數字軟起動器的硬體控制電路；研製了採用80c196kc單片機和gal16v8可編程器件構成的數字移相觸發系統；給出了數字移相觸發控制方法，分析和討論了該方法的工作和設計原理；採用了一種參數自整定的混合型模糊pid控制方法。
  11. Relay - contactor control unit is employed in pulse power supply to fulfill the function of charging, discharging and fast charging which has the features of the strong ability against the violent electromagnetic interference and the high stability

    脈沖電源的充電、泄放電和快速充電等單元的控制採用抗干擾能力很強的繼電器?接觸器控制單元來完成。運行頻率的設定以及快速晶閘管觸發脈沖的產生由計算機控制單元完成。
  12. Lets you quickly display any active signals, automatically setting the vertical, horizontal and trigger controls for the best display

    自動定標autoscale能怏速顯示任何活動設置垂直標度水平標度和觸發控制
  13. Then the complete simulink simulation model of soft cut - in system is established. what is more, an effective control strategy of soft cut - in unit that the cut - in rotate speed of wtg and scr phase - shifting rule should be adjusted in accordance with the rotate acceleration of rotor is put forward. on the basis that the simulation model is validated, the simulation and analysis of direct cut - in and soft cut - in process of wtg are carried out, which aims at supplying necessary referential material for the r & d of soft cut - in unit

    本文以軟並網裝置主電路的分析與設計?軟並網控制系統的建模與模擬分析?可控硅移相觸發軟並網控制電路的設計為主線，首先進行了軟並網裝置主電路部分的分析與設計；然後建立了雙繞組風電機組的完整模擬模型，在對模型進行驗證的基礎上，提出了有效的風電機組軟並網控制策略，即機組並網轉速與可控硅移相規律應隨電機轉子加速度進行調節，並進行了風電機組直接並網與軟並網過程的模擬分析，得出了相應的結論，為軟並網裝置的研製提供了必要的參考依據；最後設計了軟並網系統的可控硅移相觸發控制電路的硬體與軟體的實現方案，並提出了系統硬體與軟體的抗干擾措施，重點闡述了主要軟體模塊的實現方案。
  14. It emphases the selection of secondary voltage of the step - down transformer, the control and protection of thyristor, the calculation of compensation capability and group capability, the technique of cross - zero switched on / off capacitors or reactor, the solution of avoiding possible resonance in switching on / off groups of capacitors or reactor and the measure of the best time to switch ( including the design of the computer survey and control system, instrument deliver system, delay operate and protect system ). although thyristor as a no - contact switch can avoid almost the problem of contact switch with contact, it can not solve the over - voltage, over - current and transient process itself as switching on / off capacitors or reactor. so we must develop a set of thyristor - switched control and protect system with great reliability so that it can realize of cross - zero switching on / off capacitors or reactor at any time

    晶閘管具有過零、動作快速的特點，本研究以晶閘管為電容器和電抗器的分組投切開關，重點研究了協調變壓器二次電壓的選擇、晶閘管觸發控制及保護、動態補償容量及分組容量的計算確定、過零投切電容器和電抗器技術的實現、以及分組投切電容器和電抗器可能發生諧振的處理計算方法，給出實現最佳補償投切選擇方法（測控系統、儀表變送系統、操作和保護系統的設計步驟） ，研製了一套高可靠性晶閘管觸發控制及保護系統，實現對無功的靜止可調補償。
  15. The machine has the motor and the switch can be controlled by touch, it ' s volume is small and easy to install, which the typing word don ' t fade

    列印出生產日期、批號等，該機自帶電動機行程開關觸發控制，體積小、安裝方便、使用簡單、維修方便。
  16. It also discusses some key techniques such as the design of ecl circuit, high speed signal processing and external trigger control

    並對ecl電路、高速信號及外部觸發控制等關鍵技術進行了詳細的討論。
  17. The module is composed of the vxibus interface, data acquisition and storage circuit, analog conditioning circuit and trigger control circuit. measurements such as period, frequency, voltage, pulse width are supported by the acquisition and storage of the input signals

    該模塊主要由vxi介面電路，數據採集及存儲電路，信號調理電路和觸發控制電路等各部分組成，可以完成信號的採集、存儲，支持信號的周期，頻率，幅度，脈寬等參數的測量。
  18. The floating - point a / d conversion scheme was employed to increase the system ' s dynamic range. complex programmable logic device ( cpld ) was also used to perform the system ' s function such as data sampling trigger control and data storage control, etc. aduc812, a new type of microprocessor with full a / d converter, was utilized to fulfill the a / d conversion

    在數據採集電路設計中，採用了浮點放大技術來提高系統的動態范圍；通過引入可編程邏輯器件來實現觸發控制、存儲控制；采樣過程中應用了時序重疊技術，從而實現了數據採集系統的流水線作業方式。
  19. Within it are triggering mechanisms in various forms - that awakening your memory about who you are - why you are here - and the stirring you feel in your soul that something major is about to change for the better

    在藍圖里有各種各樣的觸發控制裝置-喚醒有關你是誰的記憶-你為什麼在這里-以及你感知到在靈魂里的喜悅，你感知到主要是將會變得更好。
  20. Topics on computer interface control technologies are discussed in detail, together with hardware design on control circuit, interpolation algorithm, and control software. all of our efforts are concentrated in one purpose - to establish a cnc system suitable for excimer laser micro fabrication. based on computer local bus tech.,

    本文針對由反應式步進電機驅動的微加工工作臺控制和準分子激光器外觸發控制特點，就計算機介面控制技術、硬體控制電路設計、插補演算法求解、控制軟體實現以及準分子激光微刻蝕加工過程進行了較詳細的討論。
分享友人
分享到 Line

分享到臉書