計曲線 的英文怎麼說

中文拼音 [jìqūxiàn]
計曲線 英文
accented contour
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 曲線 : [數學] curve; bight; bought; profile; net曲線板 french curve; irregular curve; curve board; splin...
  1. The waves should be sheared waves for the anisotropic aeo device and longitudinal waves for the isotropic aeo device. geometrical relationships of anisotropic acousto - optic effect in ln crystal and kdp crystals are studied by tangent - match condition. curves of incident angle vs. abaxial angle, diffractive angle vs. abaxial angle, extreme frequency vs. abaxial angle and acousto - optic merit vs. incident angle vs. abaxial angle are systematically gained and the design parameters are also calculated

    利用相切-匹配條件法研究了鈮酸鋰晶體及kdp晶體的反常聲光互作用幾何關系，系統地得到了以離軸角為自變量的各參數的計算公式及相應的關系曲線，通過數值分析方法給出了聲光優值隨中心頻率的變化曲線並給出了器件的設計參數。
  2. In this paper, using the program ( epagpll ), the bored testing pile group of the chinese architecture science and research institute at luokou area are analysised. the comparisons among analytical results of four constitutive models of soil are made, and the deformation of piles and soil, the soil resistance of the piles, the friction beneath cap, the aclinic displacement of the ground soil before piles and the failure pattern of pile group are discussed in detail

    本文利用所編的程序，對上海地區豎向荷載作用下的單樁的流變效應進行了分析，並通過樁體位移?時間關系曲線，確定軟土地基上豎直受力樁的承載力，分析了豎直受力樁的最終沉降量的大小，並結合《上海地區地基基礎》地方規范就程序計算結果進行了對比。
  3. For this purpos, from the point of the log geology, aimed at the actuality of the current fractured reservoir log geology interpretation and evaluation, based on synthetical analysis of the current domestic and foreign fruit of fractal dimension investigation of reservoir fracture, using the method and technique of fractal dimension, through the further discussion of the fractal dimension characteristics of m index and n index in the log interpretation archie model in a sample way and through the theoretic reasoning to the fractal dimension dfa and m index of fractured reservoir interval ' s log curve, according to the geophysical signification of the fractal dimension dfa of fractured reservoir interval ' s log curve shape : the more complicated the change of the curve shape is, the larger the its dfa value is, then the more complicated space structure of fracture and pore, then the higher value of m index of space structure of fracture and pore, and so on, the text propounds an improved method, based on box dimension, of covering log curve with scale grid, and by programming computes the dfa and its m index value of fractured reservoir interval ' s log curve, for instance, ac and rt curve, ect, then further puts this technique into application investigation, and makes analysis of application effects in the reservoirs located in l area of qx oil field from three aspects : 1. the dfa and its m index value of fractured reservoir interval ' s log curve, for instance, ac and rt curve, ect, which are derived from computing, is used to identify reservoir type by crossplotting m index with the product df _ acrt of fractal dimension of acoustical wave log curve and restivity log curve and by experiential discriminance plate of reservoir type in l area of qx oil field

    因此，對該區裂縫性儲集層的類型識別、孔滲特徵的測井地質解釋以及儲層裂縫的發育和分佈規律進行深入的研究便成為本文研究的出發點。為此，本文從測井地質的角度，針對當前裂縫性儲層測井地質解釋與評價的現狀，在綜合分析當前國內外儲層裂縫的分形分維研究成果的基礎上，利用分形分維方法和技術，通過對archie測井解釋模型中的m指數、 n指數的分形分維特性的深入淺出的論述以及裂縫性儲層段測井曲線分維d _ （ fa ）與m指數的理論推導，根據裂縫性儲層測井曲線形態分維值的地球物理意義? ?曲線變化越復雜，則其分維值d _ （ fa ）越大、裂縫孔隙空間結構越復雜、裂縫孔隙空間結構指數m值越高等特徵，提出了改進的基於盒維數的測井曲線網格覆蓋法，編程計算了裂縫性儲層段常規測井曲線（如聲波和電阻率曲線）上分形分維值及其m指數值，進而從以下三個方面對qx油田l區塊的裂縫油藏進行應用研究，效果十分理想： 1將計算得到的可變的m指數與聲波和電阻率分維之積df _ acrt進行交繪，採用儲層分維值分類技術統計分析這些參數變化的規律，並結合qx油田l區塊儲層類型經驗判別圖版，從而實現qx油田l區塊下白堊統的裂縫性儲層的類型識別。
  4. A comparison of the experimental and calculated distribution curves should provide a robust check of the adequacy of this model.

    將實驗測得的和計算所得的分佈曲線進行比較，應該對這個模型是否合適這一問題提供有力的校驗。
  5. Using his data from 1830 - 1995 with statistics, the hyperbola and its asymptotes, he estimated 47 new ( species ) of sea monsters are still undiscovered

    帕克斯頓利用統計學、雙曲線以及它的漸近線，分析他收集的1830年與1995年之間的數據，估計還有47種新海洋怪獸有待我們去發現。
  6. Win2000 bed lift is of personalized design, ultra - stable operation, to offer quietness and comfortableness to the greatest extent to patients with warm colors. it is provided with variable voltage variable frequency device, to produce the best operating curve in accordance with the physiological requirements of human body, to show make the safe, comfort, stable and excellent perfomance in the whole process during the operation of the lift from start, acceleration, deceleration to stop. optional cut - off emergency leveling device may be equiooed at the demand of user to ensure that the passengers inside the lift can be rescued in case of power cut - off accident

    Win2000系列病床電梯以人性化的設計，超平穩的運行，給予病患者最大程度的安靜舒適增添溫馨的色彩。採用先進vvvf調頻調壓調速裝置，按人體生理要求由電梯優化產生最佳的運行曲線，使電梯的起動加速減速停止過程處處體現安全舒適平穩的卓越性能。根據用戶要求可選裝停電應急平穩裝置，確保以外停電時，被困電梯內的乘客能及時獲得解困。
  7. Abstract : propagation characteristics of r wave in a pavement structures are analysed in this paper. based on the propagation characteristics of r wave, the horizontal propagation wave is simulated by using r wave, the vertical propagation wave is also simulated by using body wave in calculating dynamic response of pavement structures. the availability and accuracy of dispersion curves measured by sasw in pavement structures is analysed by using the presented method used to calculate dynamic response

    文摘:利用有限單元法分析了道路結構的r面波傳播特性：在深度方向上衰減較慢，傳播較深，波動性大.提出了在道路結構動力響應計算中，利用面波來模擬水平向傳播波，利用體波來模擬豎直向傳播波.通過算例來驗證該方法的可靠性和精確性，並利用這一動力響應計算方法分析了道路結構表面波測試中所獲彌散曲線的可靠性
  8. ( 2 ) based on indoor test, two typical soft rock of brecciated mudstone and siltstone in luohu jiancheng district is carried systemically though interior rheological testing ; moreover combining with preceding studying results of rock rheological constitutive model, rheological numerical constitutive model suited to rock mass mechanics characteristics and stratum structure of luohu fracture zone, and numerical parameters of the model are processed with studying of curve fitting

    （ 2 ）立足於室內試驗，對羅湖建成區兩種典型的軟弱巖石?含角礫泥巖和粉砂巖進行系統的室內流變試驗研究，又結合前人對巖石流變本構模型的研究成果，分析並確定了適合羅湖破碎帶巖體力學特性及地層構造特徵的流變計算本構模型，並對該模型的計算參數進行了曲線擬合研究。
  9. Abstract : the design, manufacturing and measurement method of cam profiling are discussed in this paper by describing cam shaft grinding, fabrication of cam profiling, formation of contour of cam profiling, method of compensative fabrication of cam profiling, and measurement and evaluation of cam profiling

    文摘:從凸輪軸磨床磨削工件凸輪、反靠凸輪靠模的過程，凸輪靠模輪廓曲線的形成，補償反靠凸輪靠模的方法，標準凸輪軸的刮削及補償量的確定，凸輪靠模的檢測與評定等，論述了凸輪靠模的設計、製造與檢測方法。
  10. Also, they were favor for further explanations and canalization. the results of solar heating rate and infrared cooling rate and the model output were displayed as data forms and curves in the paper

    文中將加熱率和冷卻率的計算結果以及與之相關的模式計算結果（可見光波段的大氣輻射收支和紅外波段的大氣輻射收支）以數據表和曲線圖的形式列出。
  11. This paper deriving the theory work inflection point in the static stage characteristics curve of small measurement range linear dimension measurement. by the way of high pressure and back pressure pneumatic measure and designed the parameter of the mainly and measure spray head, which are the key component in the spray head - baffle pneumatic sensor. the different groups for the main - spray head and the measure spray head, will effect the dynamic and static stage characteristic parameter. the author have done contrast experiment and optimization design to test and verify the theory derivation whereby made the rang of show valve of pneumatic measure system measure range up to 40 u m, the sensitivity up to 100mv / u m, resolution up to 0. 05 p m, the uncertainly of measure is less than 0. o2 u m, satisfaction of requirement of groups the carboy hatch thickness size precise measure of soft shims

    對高壓背壓式氣動測量用於小量程線性尺寸測量的靜態特性曲線的理論工作拐點進行了推導，對氣動測量系統中的噴嘴-擋板型氣動傳感器中的關鍵部件? ?主噴嘴和測量噴嘴的參數進行了理論設計，對主噴嘴和測量噴嘴的不同組合，將影響測量系統靜、動態特性指標的噴嘴參數進行了對比實驗和優化設計，並通過實驗驗證了理論推導，從而使氣動測量系統量程的示值范圍達到40 m ，靈敏度達到100mv m ，解析度達到0 . 05 m ，測量不確定度小於0 . 2 m ，滿足了壓縮機缸蓋軟體墊片厚度尺寸精密測量分組的要求。
  12. Based on field research and the dynamic analysis of remote sensing data of different time ( 1987 tm, 1996 tm and 2000 china - brazil earth resource satellite ccd ), using multi - information of research area ( including data of geology, geography, hydrology, meteorology, economy, human culture and dem ) and existing research results, the dissertation discusses drive factors of desertification and the relationships between drive factors and desertification with the help of gis tool and some mathematical methods such as probability, statistics, curvilinear estimation, logical analysis and analytic hierarchy process

    論文在對研究區土地荒漠化現狀野外調研和不同時相（ 1987tm 、 1996tm和2000ccd ）遙感圖像土地荒漠化信息提取和演變分析的基礎上，結合研究區已有的多元信息基礎資料及研究成果（包括地質、地理、多時期的水文氣象、經濟、人文以及dem數據等） ，運用gis強大的空間分析功能和概率統計、曲線估計、邏輯分析、主成分分析、層次分析等數學方法綜合研究了土地荒漠化與各驅動因子之間的相關關系，揭示了研究區土地荒漠化的主要驅動因素，探討了荒漠化動態演化規律。
  13. To select a cylindrical plane cathode ; to design proper focus electrodes in order to control the formation of beam in methods of solving equations, electrobath and simulation aided by computer. to correct effects of anode hole and work out curves of designing guns ; to discuss plasma cathode guns at last

    選用圓形平面陰極;設計恰當的聚束極形狀以控制電子束的成形，並使用解析法、電解槽法和數值方法三種方法進行設計;考慮陽孔效應對電子束傳輸的影響，修正陽孔效應，給出電子槍設計曲線;最後討論一下等離子體陰極電子槍。
  14. In this research, the lime - fly - ash bound macadam was joined with steel fibers, glass fibers and polypropylene fibers with the contents of the lime, the fly ash and the macadam fixed in lab tests. the study focuses mainly on the split strength, compression strength, and modulus of compressive resilience and shrinkage property of the lime - fly - ash bound macadam enhanced by different kinds of fibers. based on the test, a detail theoretical analysis was made on the relation of mechanical property, dry shr inkage with the variety and the quantity of fibers, applying the theories of strength, dry shrinkage and the methods of statistics, curve mimesis and variance analysis

    本論文主要是研究在同一種二灰碎石混合料（石灰、粉煤灰、集料的含量及比例相同）中分別摻入不同數量的鋼纖維、玻璃纖維、聚丙烯纖維，通過室內試驗對其抗拉強度、抗壓強度、抗壓回彈模量和乾燥收縮性能與纖維摻量和纖維品種之間的關系加以分析和研究，並在此基礎上根據二灰碎石強度形成機理、乾燥收縮機理和數理統計、曲線擬合、方差分析的方法分析纖維品種和纖維數量對二灰碎石的力學性能和乾燥收縮性能的影響，最後得出纖維對二灰碎石的強度、抗壓回彈模量、乾燥收縮有很顯著的影響，並提出了相應的建議。
  15. This paper researches basic principle of microwave digital phase shifter deeply, reviews different theories of all kinds of microwave digital phase shifter circuit, analyzes loaded - line phase shifter in detail and draws design curves according to formulas. and this paper presents a novel method, which makes use of modeling simulation that software - ansoft serenade 8. 7 provides to evaluate parameter values of pin diodes through s parameter measurement. then, a kind of 6 - bit digital phase shifter circuit is designed and simulated through software - ansoft serenade 8. 7

    本文對微波數字式移相器的基本理論進行了較深入的研究；綜述了各種微波數字式移相器電路的工作原理，著重對加載線式移相器電路進行了理論分析，並根據計算公式作出一系列相應設計曲線；提出利用軟體ansoftserenade8 . 7所提供的測量數據擬合功能，通過測量s參數來確定pin二極體等效電路參數的新穎實驗方法；利用微波電路設計軟體ansoftserenade8 . 7對6位數字式移相器電路進行模擬、優化設計，做出樣品，並對其性能測試分析，對研製微波數字式移相器具有重要的參考意義。
  16. The relations between the dummy stress amplitude and fatigue life can be easily developed. and then, the bhw - 35 steel fatigue design curve can be obtained according with asme criterion and bs5500 criterion. compared ~ vith the design curves provided by the asme and bs5500 criterion, the curve got in this paper provides reliable direction for the fatigue design of boiler drum, which used on the altering generating power plant set

    將焊縫材料的虛擬應力幅與壽命關系，按照asme和bs5500規范的方法分析得到bhw ? 35鋼疲勞設計曲線，並與asme和bs5500規范中的設計曲線進行比較，為我國調峰機組410t / h鍋爐汽包疲勞設計提供可靠的實際依據。
  17. Besides, in the paper the author has done some theoretical analysis and drawn design curves, trying to explain the circuit amended of the switch - line phase shifter

    此外，論文還闡述了對開關線式移相器電路進行的改進，完成了部分理論分析，繪制出相應的系列設計曲線。
  18. Designing curve is obtained by iteration, and the least time is achieved based on the requirement of error

    通過迭代確定了設計曲線，並且根據誤差要求確定了最小迭代次數。
  19. The design schematic diagram of the system and the principle designing curves of polygonal functions are given, the transfer functions in some relative segments of steam turbine and boiler coordinated control system are deduced,

    給出了系統的設計原理圖，以及折線函數的原則設計曲線，推導出了機爐協調控制系統中有關環節的傳遞函數，分析了系統的工作原理。
  20. In the chapter 4, the theory that multi - stroke curve should be designed according to the functional requirement of the hydraulic motor was posted. in other words, the multi - stoke curve was designed according to the optimization of efficiency and the rotate speed, the stability of the torque were considered at the same time. the pro / e was used to analyze the its performance and the cam files were created

    第四章在內曲線液壓馬達定子曲線的設計計算中，首次提出了按效率優化的原則設計曲線的理念，結合轉速、扭矩無脈動、等接觸應力設計理論等研究成果，採用美國參數技術公司的pro / e軟體的motion分析模塊進行cae分析，並且生成計算機輔助加工（ cam ）文件，直接驅動cnc加工機床進行定子曲線的加工，獲得了十分理想的結果。
分享友人
分享到 Line

分享到臉書