計算單元 的英文怎麼說
中文拼音 [jìsuàndānyuán]
計算單元
英文
calculating element-
Every administrator has equal administrative authority within their assigned authority of administrator, configurator, operator, or monitor to the entire cell
每個管理員對于整個計算單元都具有相同的管理權限(在其分配的管理角色內:管理員、配置人員、操作員或監視人員) 。A distributing model i s desi gnc ( l ( ) n ilgc ' nt - - de ' s ign mode so the system can be organized in d i fferent c ( ) inplltc un l [ s
設計了基於代理設計模式的分散式模型結構,很好地解決了如何將系統部署在不同計算單元。When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved
分析斜支承連續曲線箱梁橋時,採用考慮翹曲作用的曲線格子梁分析方法,應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析,考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致,引入支座節點坐標矩陣,使得梁端的位移未知量與斜支座約束方向一致,來計算單元剛度矩陣和單元節點力,然後按照矩陣位移法組集總剛並建立結構剛度方程,根據結構剛度方程即可求解未知的節點位移及桿端力,推導出任意截面處的內力計算公式。3. the calculating elements and the calculating model of rib - column, rib - beam and retaining plate of the supporting structure are proposed in this paper
3 、提出了肋柱、肋梁和擋土板的計算單元劃分以及計算模型的確定方法。Applications in the same cell, even with global security and java 2 security enabled, can potentially compromise other applications in the same cell by accessing resources of those applications or altering the cell configuration
在同一個計算單元中的應用程序(即使啟用了全局安全性和java 2安全性)可能會通過訪問其他應用程序的資源或改變計算單元配置,從而潛在地破壞( 2 ) for estimation of influences of hydraulic engineering ( control factors ) on floods, a reservoir regulation model is established based on calculation units controlled by each reservoir and reservoir system co - operations
建立了以每個水庫控制面積為計算單元的水庫(控制性因素)對洪水影響計算模型。In these regions, an expensive high - order accurate eno scheme is applied to evaluate the numerical flux at cell boundaries. and hi smooth regions a cheap spline interpolation is used to get the value of the numerical divergence from values previously obtained on lower resolution scales to save the computational cost
在這些奇性區域,我們利用代價昂貴的高階基本無振蕩格式計算單元邊界的數值通量;而在解光滑的區域,則用廉價的樣條插值根據先前低分辨尺度上得到的值來計算出其數值散度,從而減少計算工作量。The application itself can use the jmx apis for administering the cell
應用程序本身可以使用jmx api來管理計算單元。Each has administrative authority over the other
每個計算單元都對另一個計算單元具有管理權限。According to the elastic bucking theory this paper reviews and compares the calculations that such member bend around the reat axis and the hollow axis as well as bend with torsion around the hollow axis. here this paper presents a formula of calculating b used in with the h - shaped anglicizing element. meanwhile, this paper deduces out a formula of calculating b. by, which the member could be controlled to only buckle around the real axis
本文根據彈性屈曲理論對雙肢格構式單軸對稱綴板柱繞實軸、虛軸以及彎扭屈曲進行了計算分析和比較,提出了繞虛軸側向屈曲的換算長細比_ ( oy ) = ( y ~ 2 + l ~ 2 ) ~ ( 1 / 2 )中的值用h計算單元指出的計算公式,同時推導出了單軸對稱綴板柱只出現繞實軸彎曲屈曲的最小肢間間距b 。Moreover, with the datum come from calculation and test, it seams that after the number of batten floor n > 3 the change of b effected by n is too weak to be ignored. hence, that indicates it is available that the laterlly buckle of the batten column with the single axis of symmetry could be calculated with b worked out from h - shaped anglicizing element without n
此外,由電算和實驗分析可見,值在綴板層數n 3以後,其變化受n值的影響不大,這說明用h計算單元導出的與綴板層數無關的值計算公式是可以用於單軸對稱綴板柱的側向屈的計算。Any j2ee application that runs within the cell can potentially access any j2ee resource
任何在計算單元內運行的j2ee應用程序都可以潛在地訪問任何j2ee資源。Qdz process pneumatic control system. computing unit
Qdz氣動單元組合儀表.計算單元This can occur if the cell failed to format its value
未能計算單元格的首選寬度或高度。If you are taking advantage of subject propagation see
如果在使用跨計算單元主題傳播(請參閱Calculates the preferred size, in pixels, of the cell
計算單元格的首選大小(以像素為單位) 。Control to calculate the sum of cells a1 through a5, uses the
屬性來計算單元格a1至a5的和,使用Process boundaries have little impact on cell security
進程邊界對計算單元安全性幾乎沒有影響。Details the process of creating and using calculated cells
詳細介紹創建和使用計算單元的過程。The net is that both cells now completely trust each other
最終的結果是,這兩個計算單元都完全信任彼此。分享友人