計算失能 的英文怎麼說

中文拼音 [jìsuànshīnéng]
計算失能 英文
dyscalculia
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 算 : Ⅰ動詞1 （計算數目） calculate; reckon; compute; figure 2 （計算進去） include; count 3 （謀劃;計...
  • 能 : 能名詞（姓氏） a surname
  • 計算 : 1 （求得未知數） count; compute; calculate; reckon; enumerate 2 （考慮; 籌劃） consideration; pla...
  1. In the dissertation ' s chapter 3 to chapter 5, the mechanical and physical performances of the engineering plastics are analyzed, the failure mode and the designing computing methods of engineering plastics member suffering the static load, dynamic load, impact load, pulse load, are studied. by the practice application and ball firing experiment of the engineering plastics key piece in the weapons, the precious experiences, for engineering plastics application and confirmation of the material performances guideline in the weapons, are obtained

    論文的第三章至第五章，分析了工程塑料物理機械性能，研究了受靜載荷、動載荷、沖擊載荷及脈沖載荷下工程塑料構件的失效模式和設計計算方法，通過工程塑料在槍械關鍵受力結構件上的實際應用和實彈射擊試驗，取得了寶貴的經驗，為高性能工程塑料在槍械上的應用和材料性能指標的確定奠定了基礎。
  2. On the basis of investigations into the progressive yield process and the possible failure modes of rcc gravity dams, the quasi - elasticity design limit state of the ctrtical stability criterion is proposed and the real working state of the dams designed according to the ctriterion is discussed. a check formula using the material strength reducing factor as the safety index and a simplified formula similar to against sliding stability fromula are derived. finally, the corresponding design safety factors are given by using fem calculations with various influence parameters to be taken into account

    本文在研究碾壓混凝土重力壩漸進破壞過程和可能失穩方式的基礎上，提出了以準彈性臨界作為穩定臨界準則的設計極限狀態，分析了按該準則設計的大壩的實際工作狀態，導出了以準彈性強度儲備系數為設計安全指標的審查公式以及形式與抗剪斷公式相同的簡化公式，探討了定量計算考慮各種因素影響的相應設計安全系數的合理取值，並與現行規范方法進行了比較
  3. Methods : the tb economic burden was calulated as daly

    方法：採用失能調整上（ daly ）方法計算疾病經濟負擔。
  4. Monitor apparatus can measure valid value of three phase voltage and current, power factor, three phase disequilibrium, instant flecker of short time and harmonic without twenty, degree and harmonic distortion total. the paper are laid on the following. ( 1 ) master plan and function of circuit, ( 2 ) hardware design including circuit and principle of a / d conversion, phase lock, liquid crystal display and keystroke and so on, ( 3 ) design of system software including digital filtering, fft, a / d conversion and monitor interface of pc, ( 4 ) system test

    監測儀能夠完成包括三相電壓、三相電流的有效值、功率因數、三相不平衡、電壓短期閃變、以及20次內的諧波、諧波相位、諧波失真總量等的測量。論文重點介紹了以下幾部分： （ 1 ）電路的總體設計和功能； （ 2 ）硬體設計，包括a d轉換、鎖相環、液晶顯示和按鍵輸入等原理和電路。 （ 3 ）系統軟體設計，包括a d轉換、 fft 、數字濾波等程序的原理和演算法以及上位機監控界面的設計； （ 4 ）系統測試。
  5. The worm, dubbed ganda - a, spreads by sending itself to e - mail addresses on an infected machine and tries to disable anti - virus and other security software and infect certain files on the hard disk, according to sophos

    據說，這種病毒名為" ganda - a " ，通過在被感染的計算機上向其他地址發送郵件來傳播，並可能使防病毒和其他安全軟體失效，進一步攻擊計算機硬盤上的有些文件。
  6. Since the varies of gun attitude angle and the vertical vector of the homograph plane are one - to - one, all the elements of modulation gun can be transformed into the calculation of the vertical vector angle, which avoids the calculation accuracy loss of the traditional approach under the condition of the tiny attitude angle disturbance

    由於火炮姿態角變化與相應平面的法向量是一一對應的，從而可將調炮諸元轉化為法向量夾角來計算，這樣可避免傳統方案在微小姿態角擾動情形下導致的計算精度可能的損失。
  7. Article 13 when calculating the original areas of lands held by the landownership holders before consolidation of farm lands according to paragraph 3, article 8 of the act, in case of loss of or incomplete data on allocation, the average area ratio of agricultural lands to the lands for waterway partaken by the landownership holders for land reallocation within the administrative scope of the local municipality or county ( city ) shall be used as the standard for calculation unless the original landownership holders can provide certification documents

    第13條依本條例第八條第三項規定計算原土地所有權人在農地重劃前之土地面積時，其農地重劃相關資料滅失或不全者，除原土地所有權人能提供可資證明文件外，以當地直轄市、縣（市）行政轄區內辦理農地重劃土地所有權人分擔農、水路用地面積比例之平均值為基準計算之。
  8. To attain the high - power, well - proportioned and steady high - energy particle beam is the base of analyzing beam loss. the factors that influence the emission performance of the filament are analyzed, and the parameters are calculated. the experiment results proved the correctness of analyses

    獲得大功率、均勻、穩定的高能粒子束是進行束流損失分析的基礎，本文分析了影響燈絲發射特性因素，對燈絲各參數進行了設計計算，實驗證明了分析的正確性。
  9. The effect of reynolds number on rudder hydrodynamic performance is also analyzed. up to the stall angle the computed lift and drag agree well with measurements and other author ' s calculations, whereas stall angle, lift and drag beyond the stall angle are slightly under - predicted. the solver is used to investigate laminar and turbulent separated flows around a 6 : 1 prolate spheroid at high incidence angles and their effects on hydrodynamic forces

    應用所開發的求解器，以naca0015翼型舵為算例計算了船舵在不同雷諾武漢理三;大學博士學位論文數下大舵角范圍內的三維粘性流場及水動力，成功地預報了舵的失速角和最大升力，並初步探討了雷諾數對舵水動力的影響;計算結果與現有試驗和計算數據比較，吻合程度相當好，初步檢驗和驗證了該求解器精確模擬粘性流動和計算水動力的能力。
  10. The content of this thesis, through the deformation destruction process of th e typical nanlidu landslide along the national highway 318, uses the finite unit a nalysis of computation, revealing the elastic, plastic stress and displacement of each joint inside the slide area pointing out the distribution range of the tension stress and the plastic deformation range, computering the stability safety factor of the slide area, gaining the fixed quantity, quota that evaluates the stability of the slide area, revealing the position of the slide area which is most likely to los e its stability, thus, it can provide theoretic proof for the programs which renova te landslides

    本文的研究內容是通過318國道南里渡典型滑坡的變形破壞過程，採用有限元計算分析，揭示滑體內部每個節點上的彈、塑性應力及位移，找出拉應力分佈區和塑性變形區，計算滑體穩定安全系數，得出衡量滑體穩定的定量指標，揭示滑體最可能失穩的部位，從而為滑坡整治方案提供理論依據。
  11. 2. based on the results of experimental data of the tailrace surge tank of yi xing pumped - storage station in jiangsu province, this research investigates the methods for the head loss coefficients of throttled surge tank with linking pipe by means of the method which incorporates experimental results with theoretical analysis

    結合江蘇宜興抽水蓄能電站尾水調壓室水力模型試驗成果，採用理論計算與模型試驗結果相結合的方法，對有連接管的阻抗式調壓室局部水頭損失系數的計算方法進行了討論。
  12. Throughout the analysis and calculation of thermoelectricity cogeneration, exergy analysis method, we can know the system ' s energy lose ratio and its reason, and endeavor to improve the technology for energy return

    本文採用了（火用）分析與計算方法分析了系統中能量損失的數量和部位，為節能技術改造提供有效的依據。
  13. The interlocking software is the key component of the computer interlocking system, its failure may cause the fatal accident, such as trains come into collision or trains are toppled down. so how to ensure the reliability of the interlocking software is becoming an important subject when designing the computer interlocking system

    在計算機聯鎖系統中，聯鎖軟體是執行聯鎖運算的核心機構，它的失效有可能導致列車的相撞或顛覆等重大事故，如何保障聯鎖軟體的可靠性已經成為開發計算機聯鎖軟體系統聯鎖軟體的一項重要課題。
  14. It is a labor to task the faculties of a man ? such problems of profit and loss, of interest, of tare and tret, and gauging of all kinds in it, as demand a universal knowledge

    這真是一個辛苦的勞役，考驗著一個人的全部官能， ? ?這些贏利或損失的問題，利息的問題，扣除皮重的計算問題，一切都要確實數字，非得有全宇宙的知識不可啊。
  15. But now it ' s urgent to adopt new methods for calculating the head loss of regional drainage due to some factors such as long length, large flow quantity and probable strong topographic change

    由於存在管線長、流量大以及區域地形變化幅度可能較大等因素，建設區域排水系統需要採用新的方法較為準確地計算水頭損失。
  16. The representative failure models of arch rib are searched and the rib section resistances are calculated by incremental method and disadvantage loading in the control sections. the structure reliability assessment index on bearing capacity of the arch - bridge is calculated by the function of bearing capacity reliability, structure resistance probability model, load action effect probability model and jc method

    對每種荷載布置型式，採用荷載增量法進行拱橋結構失效模式的尋找和截面抗力的計算，給出其承載力可靠度功能函數，推導功能函數中結構抗力和作用效應概率模型，並利用改進的一次二階矩法計算在用拱橋承載力可靠度指標評估值。
  17. 3. on boiler retrofit, the calculation of fuel burning, the heat calculation of boiler inside structure and convection section, and the design of structure parameter of feed water heat exchanger are made. the flue gas channels " resistance calculation and the boiler strength verifying are also carried out. replacement of water cooling wall improves heat exchanging and decreases loss of heat radiant

    對鍋爐本體進行了燃料燃燒計算、爐膛結構熱力計算、對流受熱面結構熱力計算、鍋爐給水加熱器結構參數設計、煙道阻力計算及鍋爐元件強度校核等；改進了水冷壁布置使換熱效果更好，減少輻射換熱損失；改進對流段結構，更充分的利用爐膛出口煙氣余熱，提高熱效率；並且進行了煙氣阻力計算、熱效率計算和能量平衡測試，對改進后的稠油燃料和改進前進行了對比，燃燒狀況和熱效率有明顯改善。
  18. The second chapter simply introduces the development of alternate asynchronous inverter technology and retrospects some types of energy - saving systems for hydraulic elevators. then the working principles of the project are discussed and analyzed at four different working status, i. e. light load upwards, heavy load upwards, light load downwards and heavy load downwards. and the chapter focus on the introduction of structure design of pump station, calculation and type selection of pump / motor reversible units, research on oil leakage principles of accumulator circuit, design of accumulator - pump / motor pressure - energy transformer and integrated valve blocks, etc. the last but not the least, the electrical wiring of vector inverter control cabin and design of computer control and data acquisition system are introduced

    論文第二章首先簡單介紹了交流異步電動機變頻調速技術的發展概況，在回顧電梯液壓控制系統節能技術的基礎上，介紹了本課題研製的「採用蓄能器的液壓電梯變頻節能控制系統研究」的基本原理，分析了動力系統在電梯轎廂輕載上下行、重載上下行等四種典型工況下的基本工作狀態和工作方式；詳細地介紹了本課題節能系統液壓動力泵站的結構設計和參數設計，重點研究了液壓動力泵站的結構設計、液壓泵馬達可逆性問題及其選型設計計算、蓄能器迴路泄漏油損失機理的研究及其補償裝置的設計、蓄能器-泵馬達壓力能量轉換裝置的設計、多功能集成控制閥組的設計等內容；最後簡單介紹了本課題矢量控制變頻控制櫃的外部附件電氣接線、計算機控制及數據採集系統的硬體設計等內容。
  19. The surface panel method has been applied to predict the hydrodynamic performance of highly skewed propeller. the surface of propeller and its trailing vortex are discreted by a number of small hyperboloidal quadrilateral panels with constant source and doublet distribution. for highly skewed propeller, the conventional method generating grid oriented along constant radii will result in a high aspect ratio and a high skewness and a twist panel near the propeller tip on blade surface, which result easily in incorrect calculation results of velovity on blade surface, even in iteration divergence and calculation failure. a “ non - conventional grid ” is developed to acoid these problems. this grid can effectively solve the problem of the calculation and convergence for highly skewed propeller. the non - linear kutta condition of equal pressure on upper and lower at the trailing edge is executed by the iterative procedure. by sample calculating, the obtained results are satisfied the experimental data

    採用面元法預報大側斜螺旋槳水動力性能，螺旋槳表面及尾渦面離散為四邊形雙曲面元，每個面元上布置等強度源匯和偶極子分佈.對于大側斜螺旋槳而言，槳葉表面採用常規的等半徑網格劃分方法在近葉梢處將導致大展弦比、大側斜和扭曲面元，這容易使槳葉表面速度的計算結果不正確，甚至會導致迭代過程發散及計算失敗.文中建立了一種「非常規網格」劃分方法，能有效地解決大側斜螺旋槳的計算和收斂問題.槳葉隨邊處通過迭代實現非線性等壓庫塔條件
  20. The conclusion is that when, the energy group g will be supercritical, so the iteration will not converge and the computation will fail. it ' s not appropriate to set - to the left side of neutron transport equation when computing in deep subcritical system. the r indirect method deals with / v according to actual situation

    本文從定量計算和定性分析兩方面研究了深次臨界情形下本徵值計算存在困難的原因，指出當滿足關系_ （ t ， g ） + / _ g _ （ s ， g g ）時，對該能群來說可能會處于單能群意義上的超臨界，導致迭代發散，計算失效。
分享友人
分享到 Line

分享到臉書