計軸電路 的英文怎麼說

中文拼音 [jìzhóudiànlù]
計軸電路 英文
axle counter circuit
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 路 : 1 （道路） road; way; path 2 （路程） journey; distance 3 （途徑; 門路） way; means 4 （條理） se...
  • 電路 : [訊] circuit （ckt）; electric circuit; electrocircuit電路板 circuit board; 電路保持 guard of a c...
  1. Design and research on electric circuit controlling direction of the main axle of fast - hot patching robot for smelting furnace

    冶金爐快速熱修機器人主軸定向控制電路的設計與研究
  2. A novel low mechanical hysteretic ceramic capacitive pressure transducer has been made, by using of ceramic sealing technology ; integrate circuit ( ic ) technology and thick film plane fixing circuit technology. this transducer is made of a deformable ceramic diaphragm and a ceramic base plate, between which has an air cavum. a coaxial gold electrode was fired onto the diaphragm and the base plate

    本文利用新型陶瓷技術、集成電路技術和厚膜平面安裝電路技術，採用零力學滯后的陶瓷和陶瓷密封材料進行設計製造了一種非充液乾式的電容式壓力傳感器，該壓力傳感器由較厚的陶瓷基體和較薄的陶瓷膜片構成，中間形成一空氣介質腔，在基座和膜片之間內置同軸的雙電極，組成兩個電容，當膜片承受壓力時發生位移，使電容量產生變化，經後置處理電路直接轉換為可輸出的直流電壓信號。
  3. The sampling rate of the system can reach 3704 sps, and the crank angle is 1. 94 degree per sampling point corresponding to the crank speed of 1200r / min. in the mean time, the position signal of the piston could be collected by photo - electricity switch

    本研究首先設計和實現了摩擦力採集電子電路系統，裝置最大采樣率可達到3704sps ，在曲軸轉速為1200r / min時，對應曲柄轉角1 . 94度采樣點，並且可以採集用來確定活塞位置的光電開關的信號。
  4. Divider, coaxial line, trigger, signal processing, data acquisition, acquisition control and waveform analysis software is included in the device. when the device operate in the system, overvoltage is transferred to coaxial line by the divider. if the overvoltage amplitude is higher than initialization value, data acqusition card start sampling. when sampling is over, computer save data to file. engineer can analyse parameter of waveform by appropriative software reading data from file

    當裝置在線運行時，系統中出現的過電壓信號通過分壓器傳遞到同軸電纜，通過觸發電路判斷，如果大於預先設定的值則啟動採集卡的同時采樣，采樣結束后，計算機把數據存盤並以文件格式保存，管理人員隨時通過調用專用軟體調取文件進行各種參數分析。
  5. Overvoltage amplitude is higher than initialization value, data acqusition card start sampling. when sampling is over, computer save data to file. engineer can analyse parameter of waveform by appropriative software reading data from file. in the trial measurement, the device shows good performance. simulant trial and actual result indicate that method in the paper acquire approving effect, and the device can be used in the lokv distribution network

    當裝置在線運行時，系統中出現的過電壓信號通過分壓器傳遞到同軸電纜，通過觸發電路判斷，如果大於預先設定的值則啟動採集卡的同時采樣，采樣結束后，計算機把數據存盤並以文件格式保存，管理人員隨時通過調用專用軟體調取文件進行各種參數分析。
  6. In order to make the sensitivity of 2 - demension accelerometer along the two main arbors almost identical, symmetric four - beam structure that embeds a double - sides interdigitated differential capacitive with puckered beam in two directions was used as sensitive component. in addition, the differential capacitive accelerometer fabricated by bulky silicon micromechanical technique has high sensitivity, wide measurement scope, less nonlinear error, and simple converting circuit. then, the structure parameters of the sensitive component were calculated and stimulated, which results in a set of the optimized structure design parameters, main fabrication procedure and several key fabrication technology

    為使二維振動傳感器在兩主軸方向的靈敏度大致相同，敏感元件採用高度對稱的四梁結構，其中每個軸向上均採用帶折疊梁的雙側叉指電容結構，採用體硅微機械工藝製作的高深寬比叉指電容式敏感元件，具有高靈敏度、寬量程、非線性誤差小、外圍電路簡單等優點;對設計的敏感元件結構參數進行了計算，並利用有限元法進行了模擬分析，根據模擬結果得出了優化參數;在確定敏感結構的基礎上，研究了敏感元件採用體硅微機械加工工藝製作的工藝流程和關鍵工藝技術;對敏感晶元內部的c - v介面電路進行了原理設計與分析，利用差動測量技術得到由振動引起的微小電容變化量，經c - v介面電路進行相位調制處理，然後通過解調輸出與加速度成正比的電壓信號。
  7. Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error

    對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析，並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算，最後對誤差進行合成。
  8. On the analyzing of the technology trend, a plan of developing a multifunctional mark printer is brought forward the procedure of the development of a multifunctional mark printer is detailed in this thesis. a interface - card and a photoelectric board is designed, a control circuit is assembled by using them, through which a computer can control the mark printer ; a mark printer driver is developed by using com technology ; the mechanical part of the mark printer is designed by imitating milling machine ; a database software for components management is developed for high - speed train bearing industry. the managements include the registering for components, unique mark printing on components and analyzing of useful parameters. the user can complete the lifetime tracing for a component expediently

    設計介面卡和光電隔離放大電路，組成了電機控制和抬筆控制電路，通過它們pc機可以控制標號印表機工作；採用組件化技術開發了標號印表機控制軟體，驅動標號印表機工作；參考刻模銑床原理，設計了機械部分；針對高速客車軸承廠，開發了零件標號管理軟體，使標號列印和信息管理系統有機結合起來，達到在登記零件信息的同時，自動列印零件的標號，方便了對零件的跟蹤管理。
  9. In the purpose of enhance the circular polarization, the sub - array have used a phase transfer circuit which made each patch have 90deg phase difference in turn. matching branches are added to the full array to enhance the bandwidth of the antenna

    在4單元天線子陣的設計過程中採用了移相電路，使4單元間的相位依次相差90 ，展寬了天線的圓極化軸比帶寬。
  10. The main task including : when the raster ruler and axis - angle coder move forward or backward, they will bring pulse signals which are length signals and angle signals. these signals will be sent to signal processing circuits to be pretreated. then the signals will be sent to direction differentiation circuits to differentiate the directions

    主要完成以下任務：把光柵尺和軸角編碼器前進或後退產生的長度信號和角度信號，送信號處理電路進行處理，再送鑒相倍頻電路進行鑒相處理，送單片機計數，由另一片單片機把計數的結果數據經過串列通訊電路送至pc主機去進行處理。
  11. On the base of the character of hemisphere continuously vibrating, the method of actuation and measuring, the asymmetry compensating process and the measuring limit were studied, the control loop and the parameter design were introduced, which will be prepared for the future circuit design and the automobile security application

    本論文主要是在半球連續振動特性的基礎上，對陀螺儀的驅動及感測方法、非軸對稱的補償方法及感測極限進行研究，並詳細介紹其控制迴路與其參數的設計，為以後電路設計和面向汽車安全的應用打下了堅實的理論基礎。
  12. To reduce the size and increase the reliability of the control card, lattice company ? isplsi chip is used to realize the digital logic circuit. its insystem programmable ability makes it easy to realize the design of digital logic circuit

    6軸伺服控制卡上，使用lattice公司的isplsi器件實現數字邏輯電路設計，降低了板卡的設計尺寸，增加了電路板的可靠性和設計靈活性。
  13. Axle counter circuit

    計軸電路
  14. The design of measurement circuit of solid - axes photoelectric encoder

    實軸增量式光電編碼器測量電路的設計
  15. The contents of the thesis are as follows : ( 1 ) all the contents : magnetism sense fuel injector is designed. needle valve lift signal, rotation speed signal and pressure signal are collected and processed. circuit is designed. programme is programmed. ( 2 ) contents studied : the item is completed

    本課題的研究內容有: （ 1 ）本課題所要研究的內容包括:磁感噴油器的設計;針閥升程信號、主軸轉速信號、噴油壓力信號的採集與處理;系統硬體電路的設計;軟體編程等。
  16. Familiar on - line monitoring device for overvoltage just monitor inner overvoltage, but the device introduced in the paper can monitor lighting impulse overvoltage and inner overvoltage in lokv distribution system. with the characteristics of overvoltage in the lokv distribution network, the principle of on - line device for overvoltage monitoring is introduced. divider, coaxial line, trigger, signal processing, data acquisition, acquisition control and waveform analysis software is included in the device. when the device operate in the system, overvoltage is transferred to coaxial line by divider. if the

    通常的過電壓監測裝置只能監測一些內過電壓，而本裝置設計目的是能夠同時監測雷電過電壓和內過電壓。本文結合10kv配電系統的過電壓特點，提出了10kv配電網過電壓的在線監測裝置的基本原理，並研製成功了實用的在線監測裝置。該裝置包括分壓器、同軸電纜、觸發電路、信號處理、數據採集、控制和分析軟體。
  17. According to this structure, a de - coupled microgyroscope is designed, and the simulation results indicated that this three spring - mass structure can effectively eliminate the coupling effects between the drive and sense mode

    依據這種結構，設計了一種解耦型微陀螺，模擬結果表明，這種結構基本消除了垂直軸間的機械耦合，降低了對工藝精度和檢測電路的要求。
  18. Furthermore, capacitance - voltage converting circuit in the sensitive chip was designed and analyzed, and using differ - measurement technique trivial capacitance variation caused by vibration could be converted into detective voltage signal. secondly, signal processing circuit was designed and simulated

    二、對後端信號處理電路進行了設計及模擬，在外殼設計的基礎上製作出了雙軸振動傳感器樣品，並對其基本性能指標進行了測試與分析。
  19. The finite element method ( fe '. i ) is adopted to analyze the effects of the numbers of coil turns, current intensity and current frequency upon the rate of joule heat generation in details. the thermo - radiation analytical countermeasures of various types are adopted to carry out the numerical analysis of the effects of the crucible with different shapes and sizes and the blind holes with different depths opened in the tops of crucibles as well as coil positions upon the thermal field distribution whereby solving the main problem of field the thermo - field design of the induction - heating sic crystal growth system. a new combination idea of the thermo - field design obtained by means of the united design of the thermo - insulator and blind holes has been presented

    採用有限元分析方法對線圈匝數、電流強度、電流頻率等對焦耳熱產生速率的影響進行了詳細的分析討論；採用不同的熱輻射分析策略，對不同坩堝形狀、坩堝頂部開設不同深度的盲孔以及線圈的位置等對熱場分佈的影響進行了數值分析，解決了感應加熱碳化硅晶體生長系統熱場設計的主要問題，提出了通過絕熱層與盲孔的聯合設計獲得所需熱場設計的思路，給出了根據軸向溫度梯度的波動對線圈位置實行動態調節以控制熱場的理論依據。
  20. Key technologies are first introduced here such as the phased array antenna theory, dbf ( digital beam forming ) theory and the configuration of transmit and receive ( t / r ) modules. then part of analog circuitry is optimized with the digital technology. cell circular microstrip disk antenna successfully developed based on the theory of microstrip antenna, the four - celled circular microstrip disk antenna arrays are designed, simulated and analyzed with eda tools - hfss, opt1metrics

    本文以相控陣雷達組成為主軸，逐一對相控陣雷達關鍵技術中的天線陣原理、數字波束形成（ dbf ）技術和收發（ t r ）組件組成進行詳細的分析，利用數字技術對傳統相控陣雷達設計方案中的模擬電路部分進行改進；在理論設計單元圓形微帶貼片天線單元的基礎上，利用微波模擬軟體hfss和optimetrics對四單元的圓形微帶貼片天線陣進行設計與模擬；對相控陣雷達的幅相監測技術進行理論分析和討論，選擇最佳的幅相監測方案。
分享友人
分享到 Line

分享到臉書