設置參考角 的英文怎麼說

中文拼音 [shèzhìshēnkǎojiǎo]
設置參考角 英文
set preferred angle
  • 設 : Ⅰ動詞1 （設立; 布置） set up; establish; found 2 （籌劃） work out : 設計陷害 plot a frame up; fr...
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 參 : 參構詞成分。
  • 考 : Ⅰ動詞1 （考試; 考問） examine; give [take] an examination test or quiz 2 （檢查） check; inspect3...
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  • 設置 : 1. （設立） set up; put up 2. （設置） install; fit
  1. Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece

    將液體火箭發動機燃燒室的冷卻通道設計為斜航線（等傾角螺旋線）槽形，可以大幅度改善燃燒室的冷卻性能.斜航線冷卻槽的槽寬尺寸較小而槽深尺寸較大，所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點，提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜，手工編制數控加工程序難度大.為了解決數控加工程序的編制問題，研究了斜航線的數學模型，開發了自動編程軟體系統.使用該系統，可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大，加工難度大，是斜航線冷卻通道加工的最典型工件.經過理論分析和實際切削實驗，研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術，已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用，驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功，對其他相似類型零件的加工亦具有參考意義
  2. The position and size of the monochromator, focusing curvature radii and tilting angles of the germanium focusing monochromator under different different take - off angle, size and divergency of the second collimator and intensity loss due to the use of it were determined. the neutron flux at different wavelength, under different reflection and take - off angle of the monochromator and divergency of the first collimator, were given. the simulation on the aperture used for limiting beam size in front of the sample showed that, smaller the size of the aperture and further the distance from the aperture to the sample, greater the loss of the intensity and more serious the spread of the beam along vertical direction at the sample position which makes the practical sampling volume greater than expected

    用蒙特卡羅模擬方法對中子應力衍射譜儀的設計方案進行了優化研究，提出了一系列可供參考的數據：確定了單色器的位置、尺寸、垂直聚焦單色器在不同起飛角下的聚焦曲率半徑和傾角；討論了第二準直器的尺寸和發散，以及使用第二準直器造成的強度損失；給出了在不同單色器反射面、起飛角、中子波長和第一準直器發散度的情況下樣品處的中子注量率，以及多種組合情況下譜儀的解析度曲線；對限束方孔的尺寸、距離樣品遠近對強度損失和測量中的影響做了深入研究。
  3. According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling

    依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。
  4. In order to minimize the torque ripple of srd, the dissertation further design the intelligent torque control system, introduce the instantaneous torque control strategy based on torque distribute function, which is implemented by the flux linkage controller of srm. furthermore, considering the multi control parameter, the article also found the rotor position angle controller based fuzzy logic so as to optimize the whole control system and effectively reduce the torque ripple

    為了降低srd系統的轉矩脈動，本文在所建模型的基礎上，設計出智能化轉矩控制系統，利用轉矩分配函數，提出瞬時轉矩控制策略，同時採用磁鏈控制器來實現；考慮到srd具有可控參數多的特點，本文同時建立了優化轉子位置角的模糊控制器來達到智能化轉矩控制的目的，從而有效抑制sr電機的轉矩脈動。
  5. Abstract : wind tunnel experiments were carried out to investigate the influence of wind direction on the wind pressure of proximite buildings. mean and fluctuating pressure coefficients on a high building, at sixteen different wind incidences and with one and two interfering buildings, were measured in the tests. this paper presents the characteristics of wind pressure on the building, which varies with the incident wind angle and with the numbers of adjacent buildins. due to the variation of wind angle and the interference effects, the complex feature of pressure distributions can be found on the downstream building surfaces for building group arrangement at certain angle of wind attack. some area of the interfered building for such configuration, in comparison with one single building ' s, may undergo very strong positive or negative pressures

    文摘:通過風洞實驗研究了風向對兩個和三個鄰近建築風壓分佈的影響特性.實驗結果給出了在不同風向角下，作用於受擾建築上的平均和脈動風壓系數.當受擾建築處于下游位置時，建築之間的干擾效應主要表現為遮擋影響，建築物上的總體風壓系數不是很大，但在建築物表面上有時會產生局部較大的負壓系數.另外，在某些風向角下由於受到上游分離氣流的影響，在下游建築的局部表面又會出現較大正壓.這些結果可供建築布置和結構設計時參考
  6. In this thesis, on the base of analyses of the questionnaire about the dormitory at zhejiang university and the climate - oriented dormitory designs on the world nowadays. the optimized dormitory models in the yangtze delta are discussed. how to improve the physical and mental environment in the dormitory acts as a starting point for this research

    本文以長江三角洲地區為例，在對浙江大學不同年齡和年級的學生問卷調查的基礎上，從改善學生宿舍的物理環境和心理環境出發，將通風、採光以及交往空間作為基本衡量標準，將學生宿舍分解成為單元宿舍、居住組團、居住層面以及單體學生宿舍幾個不同層次，對各種布置方式優化整合，以期得出一個較為優化的學生宿舍建設模式，為本地區新建學生宿舍的設計建設提供有價值的參考。
  7. Based on the reliability, economy and feasibility of the control measures, a relatively rational reinforced scheme is selected, which can provide valuable suggestions for engineering application

    從控制措施的可靠性、經濟性角度出發，建議選擇相對合理的跨縫鋼筋布置方案，為橫縫配筋措施的初步設計和工程應用提供了有價值的參考。
  8. In addition, considering traffic security, operational efficiency and people ' s travel habits, the setting of signal phases must satisfy strong constraints, such as maximum and minimum green time, maximum queue length and smooth switch of signal timing parameters

    並且，從交通安全、通行效率及人們出行習慣的角度考慮，信號燈相位的設置具有很強的約束，如最短和最長綠燈持續時間、最大排隊長度以及信號燈的配時參數要具有一定的穩定性不能變化太劇烈等等。
分享友人
分享到 Line

分享到臉書