設置完 的英文怎麼說
中文拼音 [shèzhìwán]
設置完
英文
out point-
When all the information has been set up correctly, click the table tab at the top of the dialog to display the ground track in a tabular form, or click the map tab to display it graphically as a line on a world map
當所有的信息設置完畢,點選對話框上的「圖表」用表格的形式來顯示地面軌跡或者點擊「地圖」用一條世界地圖上的曲線的圖相形式來顯示。Holding the memory stops in position, turn the ( clockwise ) down until it stops against the valve bonnet. the memory has now been set
將記憶止動裝置保持在其位置上,順時針旋轉鎖軸環直到其停止靠到閥門閥蓋為止。記憶現在已經設置完畢。As you can see, once you get things initially set up, adding new dtds is relatively easy
正如您所見,一旦初始設置完成,添加新的dtd相對比較容易。Settings can be applied in two ways : you can completely replace your active settings with new settings or you can replace a portion of your active settings
可採取兩種方式應用設置:使用新設置完全替換活動設置,或替換部分活動設置。導入包含所有可能的設置類別的The value can be only saved after exiting the state of setting
溫差設置完成後再同時按上下鍵退出設置狀態。Press both keys at the same time to exit the state of setting after setting
設置完成後再同時按上下鍵退出設置狀態。Then press the both keys at the same time to return to the state of showing parameter code after finishing setting
鍵不放可連發,設置完成後再同時按「After setting the environment variables, you can run
在設置完環境變量后,可以運行To set the parameter, then press the set key to return to the state of showing parameter code after finishing setting
」鍵即可對參數進行設置,設置完成後再按「選擇」鍵,回到顯示參數代碼狀態。To set the parameter, then press the both keys at the same time to return to the state of showing parameter code after finishing setting
」鍵即可對參數進行設置,設置完成後再同時按上下鍵,回到顯示參數代碼狀態。Snake : hmm. . so what do i do after i set the c3
嗯. . .那麼當我設置完c3之後應該怎麼做?Close the file after setting the breakpoint
設置完斷點后關閉文件:Check it however after a while and see if it is well used
設置完之後最好是跟蹤一段時間,查看是否運行良好。When you ' re done, the dialog box should look exactly like the one shown below
當你設置完后,對話框應該看起來如下所示After the item is set,
設置完項后,Do this, and youll see the columns for name and location are automatically added
設置完后,將會看到用於name和location的列已被自動添加。Now let s talk about what you can do once you have this spec directory hierarchy set up
一旦設置完spec目錄層次結構,現在讓我們討論可以做什麼。Once all deployment report properties are set, choose generate deployment report from the
設置完所有部署報告屬性之後,請從「關系圖」菜單中選擇「生成部署報告」 。After the jre and target platform are set correctly see the toolkit documentation for instructions on doing this, all you need to do is select your application, create a new launch configuration no editing needed and click run
正確設置完jre和target platform后(有關實現這一點的說明,請參閱工具包文檔) ,您需要做的是選擇您的應用程序,創建新啟動配置(不需要編輯) ,並單擊run 。Sets full access for the specified registry keys
為指定的鍵和值設置完全訪問權限。分享友人