試件的制備 的英文怎麼說

中文拼音 [shìjiàndezhìbèi]
試件的制備 英文
medium density fiberboard―cutting and measurement of test pieces
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  • 的 : 4次方是 The fourth power of 2 is direction
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 備 : Ⅰ動詞1 （具備; 具有） have; be equipped with 2 （準備） prepare; provide with; get ready 3 （防備...
  1. At first, the bonded magnet has been produced at varied technological conditions. then the influences of varied technological conditions, such as species and quantity of coupling agent, species and quantity of agglomerant, process of compression moulding and solidification process on magnetic property and compression strength of bonded magnet have been analysis by means of apparatus for measuring magnetic property and compression strength

    首先，在不同工藝條件下制備出粘結磁體，然後利用磁性能測試儀、力學性能測試設備等測試手段，分析了偶聯劑的類型及其用量、粘結劑的類型及其用量、模壓工藝和固化工藝等因素對鐵氧體粘結磁體磁性能及力學性能的影響。
  2. The results indicated that, the fabrication process of ultra - fine grain material is mainly determined by the stress, rotate speed and the flux of cooling water. the grain refining and the hardening effect are mostly affected by the rotate speed and the flux of cooling water. compared with commercial ly12, the invalidate strength and the prolongation rate of the ultra - fine grain material are properly improved in the measurement of compression property ; and the abrupt change of the dilatability of the ultra - fine grain material at 500c is found ; also the phenomena of which the grain size of these microstructures is stable when annealed under 300c is observed

    研究表明，採用本文提出的摩擦壓扭強變形區轉移法可以得到棒狀的超細晶材料，軸向壓力、扭轉速度和溫度是採用該方法制備超細晶材料的主控參數；試件的旋轉轉速和冷卻速度對變形區晶粒細化和硬化效果影響顯著；超細晶ly12的壓縮性能與淬火+自然時效狀態的ly12壓縮性能相比，斷裂強度和延伸率均有一定程度的增強；超細晶ly12的熱膨脹系數在550左右發生明顯的變化。
  3. Plastics pipes and fittings preparation of test piece assemblies between a polyethylene pipe and an electrofusion fitting

    塑料管材和管件聚乙烯管材和電熔管件組合試件的制備
  4. Preparation of stress - corrosion test specimens for weldments

    焊件的應力腐蝕試樣的制備
  5. Corrosion of metals and alloys - stress corrosion testing - preparation and use of specimens to evaluate weldments

    金屬和合金的腐蝕.應力腐蝕試驗.焊件評定用試樣的制備和使用
  6. Corrosion of metals and alloys - stress corrosion testing - part 8 : preparation and use of specimens to evaluate weldments

    金屬與合金的腐蝕.應力腐蝕試驗.第8部分:評估焊件試樣的制備和使用
  7. Plastics - thermoplastic polyester ester and polyether ester elastomers for moulding and extrusion - part 2 : preparation of test specimens and determination of properties

    塑料.模塑件和擠塑件用熱塑性聚酯酯和聚醚酯彈性體.第2部分:試樣的制備和性能的測定
  8. Vitreous and porcelain enamels for aluminium - production of specimens for testing

    鋁用釉瓷和搪瓷.試件的制備
  9. Welding consumables. test methods. part 2 : preparation of test piece for single - run and two - run technique test specimens in steel

    焊接消耗材料.鋼的單道和雙道焊技術試樣試件的制備
  10. Unshaped refractory products. preparation and treatment of test pieces

    不定型耐火產品.試件的制備和處理
  11. Rubber - preparation of test pieces

    橡膠.試件的制備
  12. Vitreous and porcelain enamels for cast iron. production of specimens for testing

    用於鑄鐵的釉磁和搪瓷.試驗試件的制備
  13. Unshaped refractory products - part 5 : preparation and treatment of test pieces

    不定型耐火製品.第5部分:試件的制備和處理
  14. Aerospace ; boron fibre reinforced mouldings, preparation of test laminates

    航空和航天.硼纖維增強的模塑材料.層壓試件的制備
  15. Rubber, vulcanised - preparation of samples and test pieces - part 2 : chemical tests

    硫化橡膠.試樣和試件的制備.第2部分:化學試驗
  16. Unshaped refractory products - part 5 : preparation and treatment of test pieces ; german version en 1402 - 5 : 2003

    不定型耐火製品.第5部分:試件的制備和處理
  17. Adhesives for leather and footwear materials - preparation of bonded test pieces by moulding - on processes

    皮革和鞋靴材料用膠粘劑.通過制模工藝進行粘結試件的制備
  18. Rubber, vulcanized or thermoplastic - preparation of samples and test pieces - part 1 : physical tests iso 4661 - 1 : 1993

    硫化橡膠或熱塑性橡膠.試樣和試件的制備.第1部分:物
  19. Plastics. low density polyethylene pipes. preparation of specimens for physical testing

    塑料製品.低密度聚乙烯管件.物理試驗用試樣的制備
  20. Corrosion of metals and alloys - stress corrosion testing - preparation and use of pre - cracked specimens for tests under constant load or constant displacement

    金屬和合金的腐蝕.應力腐蝕試驗.恆定負荷或恆定位移條件下試驗用預破裂試樣的制備和使用
分享友人
分享到 Line

分享到臉書