試板材料 的英文怎麼說

中文拼音 [shìbǎncáiliào]
試板材料 英文
material of test piece
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 材 : 名詞1 （木料） timber 2 （泛指可以直接製成成品的東西; 材料） material 3 （供寫作或參考的資料） ma...
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 材料 : 1. （原料） material 2. （資料） data; material 3. （適于做某種事的人才） makings; stuff
  1. Fibrous polyamide material for use as an explosion suppressant and as a baffle material in aircraft fuel tanks - test methods

    飛行器燃料艙中用作爆炸抑制劑和擋板材料的纖維聚酰胺材料.試驗方法
  2. Test method for flexibility of resilient flooring materials with cylindrical mandrel apparatus

    用圓柱形芯軸裝置對彈性地板材料韌性的試驗方法
  3. Theoretical models were used to predict the effects of microcrack - density to effective tensile modulus of cf / ep laminates for long - term duration exposure for it difficult to get from tests. a uniaxial zero - expansion model was established based on the analysis of thermal stress and the coefficient of thermal expansion of the laminates

    由於受到試驗周期的限制，對于長期暴露于空間環境中的層合板材料，其有效拉伸模量很難用試驗方法直接測量，本文採用理論模型進行分析。
  4. The results of the limited element analysis and experiment study confirms that both the resisting ended batten and using angle batten in place of plate one could make the laterally stiffness of such member more strong. that maybe provides somewhat practical benefits for designing the twin - wall truss

    本文還通過矩陣分析法和模擬試驗研究，證實了端綴板的存在對抵抗側向屈曲有明顯提高；而選用角鋼代替綴板材料相對于板形板，有助於提高構件的側移剛度和翹扭轉剛度，這對于單軸對稱綴板柱的設計也具有一定的實用價值。
  5. Standard test method for density of sandwich core materials

    夾芯板材料的密度的標準試驗方法
  6. Test method for solar transmittance terrestrial of sheet materials using sunlight

    用陽光測試薄板材料的太陽能傳遞性
  7. Standard test method of sharp - notch tension testing of high - strength sheet materials

    高強度薄板材料的銳切口張力試驗的標準試驗方法
  8. Standard test method for solar photometric transmittance of sheet materials using sunlight

    用陽光對薄板材料的太陽能光度透設比的測試方法
  9. Test method for water resistance of paper, paperboard, and other sheet materials by the dry - indicator method

    用乾式指示計法檢測紙張和紙板及其它薄板材料耐水性的試驗方法
  10. Standard test method for temperature - resistance constants of sheet materials for shunts and precision resistors

    分流器與精密電阻器用薄板材料的溫度電阻常數的標準測試方法
  11. Test method for surface wettability and absorbency of sheeted materials using an automated contact angle tester

    利用自動接觸角測試儀測定薄板材料的表面濕潤性和吸水性的試驗方法
  12. Standard test method for water vapor transmission rate of sheet materials using dynamic relative humidity measurement

    用動態相對濕度測量法測定薄板材料中水蒸氣透過率的標準試驗方法
  13. Standard test method for resistance to chemicals of resilient flooring

    彈性地板材料耐化學藥品的標準試驗方法
  14. The rigidity and strength performance such as tension bend, torsion of composite laminated plates are calculated by use of classical lamination theory, and then analyses the experiment methods for rigidity and strength of laminate in detail, the comparison of theoretical analysis and experimental result shows good consistent, which indicate that the theoretical analysis and experimental method presented there is applicable for design and manufacture of military medical shelter laminate. in addition, theoretical analysis is taken for heat preservation and insulation performance of the laminate material by use of stable plate heat conduction method

    採用經典迭層理論，計算了軍用醫療方艙復合夾層大板材料的拉伸、彎曲及扭轉等剛強度性能，由此深入研究了夾層大板材料彎曲剛強度性能試驗方法，對理論分析進行了試驗驗證，結果表明該課題提出的理論分析和試驗方法適于軍用醫療方艙鋁塑復合夾層大板力學分析，對軍用醫療方艙鋁-聚氨酯-鋁復合夾層大板的力學結構設計和製造具有重要的應用價值。
  15. Standard test method for density of a sheet gasket material

    密封墊板材料密度的標準測試方法
  16. More and more military shelters are made and used by forces, but in the process of product and application, there is not the suitable theoretical instruction. base on the manufacture of military medical shelters, the article is a part of the pre - operation preparation shelter and x - diagnosis shelter, this article present theoretical analysis and experimental research for mechanics and heat preservation - insulation performance of shelter composite laminated plate materials

    隨著軍用醫療方艙大批量生產和裝備部隊，使方艙經驗性設計和研製方式的缺陷日益顯露出來，因此對軍用醫療方艙的研究，尤其是對方艙復合大板材料的研究，迫切需要一套科學的理論和試驗分析方法指導方艙的研製和生產。
  17. And, the coefficient of heat conduction, temperature rise and fall in shelter chamber experiment are made, the result shows the stable plate heat conduction method is applicable, the integration of experience formula for calculation of heat and cool load and experiment analysis is suitable for design and validation of temperature in shelter chamber, the integration can nicely reflect the condition of microclimate temperature in shelter chamber, and have importance reference value for research of microclimate condition in shelter chamber. at last, in article the comparison is made between the felt techniques and foam techniques of the laminate plates, and improved manufacture techniques of composite laminate is brought forward. the experiment indicates the improved techniques can ensure the structure strength and heat preservation and insulation performance

    基於軍用醫療方艙特殊的微環境使用要求，運用穩定平壁傳熱分析方法建立了軍用醫療方艙鋁塑復合夾層大板傳熱系數理論計算模型，對軍用醫療方艙鋁-聚氨酯-鋁復合夾層大板材料隔熱保溫性能進行了理論分析；運用經驗分析方法進行了冷熱負荷計算分析；並對兩計算採用傳熱系數和艙室升溫、降溫試驗進行了對比試驗研究，結果表明穩定平壁傳熱分析方法計算傳熱系數方法可行，為方艙鋁塑夾層大板的隔熱保溫結構和性能設計提供重要依據，並準確表徵艙室內部微環境溫度條件，對軍用醫療方艙艙室微環境設計提供參考。
  18. Standard test method for ball punch deformation of metallic sheet material

    金屬薄鋼板材料噴丸沖壓變形的測試方法
  19. Standard practice for selection of corrugated fiberboard materials and box construction based on performance requirements

    根據性能要求對波紋狀纖維板材料和箱結構進行選擇的標準試驗方法
  20. Electrostatics - part 4 - 5 : standard test methods for specific applications - methods for characterizing the electrostatic protection of footwear and flooring in combination with a person

    靜電學.第4 - 5部分:專用的標準試驗方法.與人配合的鞋靴和地板材料靜電防護的表徵方法
分享友人
分享到 Line

分享到臉書