誘導速度場的英文怎麼說

中文拼音 [yòudǎochǎng]
誘導速度場英文
induced velocity field

  • : 動詞1. (誘導) guide; lead; induce 2. (使用手段引人隨從自己的意願) lure; seduce; entice
  • : 動詞1. (引導) lead; guide 2. (傳導) transmit; conduct 3. (開導) instruct; teach; give guidance to
  • : Ⅰ形容詞(迅速; 快) fast; rapid; quick; speedy Ⅱ名詞1 (速度) speed; velocity 2 (姓氏) a surna...
  • : 度動詞[書面語] (推測; 估計) surmise; estimate
  • : 場Ⅰ名詞1 (平坦的空地 多用來翻曬糧食 碾軋穀物) a level open space; threshing ground 2 [方言] (...
  • 速度: 1. [物理學] velocity; speed; blast; bat 2. [音樂] tempo3. (快慢的程度) speed; rate; pace; tempo

※中文詞彙誘導速度場在字典百科國語字典中的解釋。

  1. Cotyledon and hypocotyl ' s rate and quamity are the most among these explams, and callus can be obtained in 10 days by cotyledon and hypocotyl. reversely it is difficult to indue callus with root, and the callus from root is lnde and easy to become browning. the calius obtained from leaf grows very slow and does not become browning uniill in 2 or 3 months

    銀杏的不同器官和組織都能夠出愈傷組織來,其中,子葉和胚軸10d左右全部愈傷化,率均最高,根則很難,愈傷組織很少,褐化很快;葉片的愈傷組織,生長慢,褐化也慢,在培養基上保持兩三個月而不褐化;胚乳的時間也較長,需要30d左右。
  2. By means of analytical methods based on upper bound element technique ( ubet ), non - axisymmetric element, simulates the forming process of non - axisymmetric involute teeth spline has been introduced, formula of speed fields been derived and the deformation regularity of steady extrusion on the forming process successly described

    摘要本文運用上限單元技術( ubet ) ,引入非完全軸對稱單元,模擬了非完全軸對稱零件漸開線齒外花鍵的成形過程,推出了成形過程中的公式,並成功地描述了擠壓過程中的變形規律。
  3. All of these is the important base of the selecting of turbines, the designing of hydrodynamics performance, and the general designing of marine currents power plant

    首先分析了豎軸可調角直葉水輪機水動力性能計算的基本公式,介紹了的兩類計算方法。
  4. Based on the reynolds " lubrication approximation, the small parameter method is introduced to approximately analyze velocity field and stress distribution between the two parallel disks with an interstitial second - order fluid. 3. squeeze flow between two parallel plates of a bingham fluid with partial wall slip is considered

    以reynolds潤滑理論為基礎,採用小參數法研究了存在滑移時兩剛性圓盤間二階流體的擠壓流動,出了流體的和壓力分佈,進而求出圓盤間擠壓力的解析表達式。
  5. The principal contributions of this dissertation are : 1. a high fidelity and real - time rotor wake inflow model was built up. based on peters - he finite states wake theory, a new influence coefficient matrix for high speed flight was derived, the modified wake model is better suitable for the flight state with a large wake skew angle

    本模型以peters - he有限狀態尾跡理論為基礎,修正了大尾跡傾斜角時的影響系數矩陣,並結合了王氏渦流理論,出了旋翼垂向分量和旋轉分量的表達式,可計算平尾、尾槳和垂尾氣動中心處各分量。
分享友人