調壓槽 的英文怎麼說
中文拼音 [diàoyācáo]
調壓槽
英文
surge bin-
Creaser linked with slotter for adjustment
壓線輪座，開槽刀座聯動調整。2 ) the structure elements should be laid out symmetrically and uniformly when designing steeve - arch structure, what ' s more, the reasonable selection of section geometric size near the arch foots of first beams is paid attention to and the arrangement difficulties of steel bar due to the big eccentric pressures 2, the analyses of anti - seismic features on transverse direction of the aqueduct l ) the method of adjusting the elements " mass can be harnessed in order to even the layout of seismic loads
2 ）設計吊桿式拱架支承結構時，各部分構件應當均勻對稱布置。另外，還應注意頭道梁拱腳附近截面的尺寸擬定，克服地震內力造成的大偏心受壓狀態給結構配筋設計增加的困難。 2 、橫槽向抗震性能分析1 ）可利用調整構件質量的方法，使得結構的某些構件的地震荷載分佈均勻一些。Mount restrictor bar into the restrictor bar groove of upper die, mount adjusting bolt for restrictor bar into the bolt hole in the restrictor bar, then mount lower press block, upper press block
在上模節流棒槽內裝入節流棒，將節流棒調節螺栓裝配進節流棒的螺絲孔中，再裝配上壓塊。After analyzed the basic principle of optimized noise reduction on tyre pattern, summarized three approaches to noise reduction. the first is trying to reduce size of single block or socket to reduce noise amplitude on time domain, the second is to adjust stripes sorting order and their interlace value to avoid noise - made by every single block - peak values on time domain overlayed and the last is to adjust ratio of blocks and sockets, ratio of stripe interval and stripe sorting order to avoid noise periodical distribution and abnormal high peak values in some frequency strip
論文第四章分析了輪胎花紋優化降噪的基本原理，總結出三條降噪途徑：在允許范圍內盡量減小單個塊或槽的大小、刻刀槽軟化花紋塊來減小噪聲時域波幅度；調整節距排列順序、花紋條之間的錯位值，使各發聲單元發出的聲壓時域波形的同向峰值錯開，避免同向峰值疊加；調整花紋塊和槽比例、節距比例、節距排列順序，盡量避免周期性分佈，使輪胎所發出的噪聲趨于白噪化，避免某些頻段的異常高峰值。The technologies, including collecting the secondary fume by electrostatic precipitator on roof, restraining the open fume by dust inhibitor and treating the mobile fume by movable ventilation installation, are emphatically described. the adjustment and control of the gas flow and the pneumatic conveyance of the dust would be widely used in dust collecting system. as to the dust collector, low pressure pulse long bag filter and surface filtering technology would be a new technique in bag filter, and enlarged equipment would be the developing trend
著重講述了屋頂除塵器、抑塵劑、移動通風槽分別是二次煙塵治理、開放性揚塵抑制、移動塵源控制的新技術措施，風量調節與控制、氣力輸灰技術將在除塵系統中廣泛應用；在除塵設備方面，長袋低壓脈沖袋式除塵技術和「表面過濾」技術成為袋式除塵新技術，設備大型化將成為方向。This machine is a kind of radial riveting machine, the machine adopted the advanced radial technology, and its movement path likes the 11 pieces of plum blossom s shape, and using the screw pole to ascend and descend the work bench the head part is fixed, and the t - slot of bench can fix the clamping apparatus available, the center hole of bench and axis are coaxial, the one - way adjusting valve of liquid current is effectively controlled riveting speed
Jm12 - c是液壓類中重型徑向鉚接機，除應用有第五代徑向鉚接技術外，該機加長了鉚接行程，該項參數由普通機型的30mm加至60mm ，可滿足長行程深孔內鉚釘鉚接的要求。工作臺，並具有夾具梯形槽，工作臺中心孔徑與主軸軸線同軸，可用於夾具定位。氣路加裝雙向調節閥，有效控制鉚接速度。Die centering in press is obtained by milling a slot on the bottom subplate parallel to the direction of the feed
通過在與進料方向平行的底部底板上銑出一個狹槽來實現壓床上模具中心的調整。Accurate control of compression through close tolerances of gasket groove and allowance for radial expansion
通過密封環槽的精密公差和徑向膨脹的修正來進行壓縮的精確調整控制。Creasing & slotting are manual adjustment type, ensure upper and lower knives are aligned to prevent knife damage
壓線與開槽為手動調整式，可確保上、下刀正確對齊，避免刀片磨損。分享友人