調整臂 的英文怎麼說

中文拼音 [diàozhěngbèi]
調整臂 英文
adjusting arm
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 整 : Ⅰ形容詞1 （全部在內; 完整） whole; all; complete 2 （整齊） neat; tidy; orderly Ⅱ動詞1 （整理; 整...
  • 臂 : 臂名詞1. （胳膊; 從肩到腕的部分） arm 2. （人體解剖學上多指上臂） upper arm
  • 調整 : adjust; tune up; trim; trimming; variation; modulation; arrangement; debug; rectification; redres...
  1. Design for aira has gone through from piston - rod journey principle to interruption check principle

    其自動調整臂經歷從開始使用活塞桿行程原理設計到使用比較先進的間隙檢測原理進行設計。
  2. There are mostly a few aspects that fully analyse for design and compute for aira : 1 design and compute for spring of rectangle section

    對自動調整臂的設計計算作了詳盡的分析，主要以下幾個方面： 1矩形截面力和彈簧的設計計算。
  3. 4 design for hatch size of control - pan relates to brake interruption setup and whole layout of aira. this article gives their correlation

    4控制盤開口尺寸的設計與制動器制動間隙的設置和調整臂的整體布置有關，文中給出了它們的相互關系。
  4. Aira ( auto - interruption regulating arm ) is an important part of air pressure braking system in automobiles. it has gone through from hand adjust to auto adjust

    間隙調整臂是汽車氣壓制動系統中的一個重要總成，它經歷了從手動到自動調節。
  5. This article analyses the structure o ' f the introduction of aira to deal with its operating principle and the design for the major components

    本文通過對間隙感知型自動調整臂的結構分析，較詳細地討論了間隙調整臂的工作原理和主要零件的設計方法。
  6. Finally, author use adams software has established mechanism system using parts were sculpted in the pro / e software environment, and has realized movement simulation of aira in the adams software environment

    最後用adams軟體對在pro e軟體中造型調整臂零件模型建立機械繫統，在adams軟體環境里實現了調整臂機構的運動模擬。
  7. This spring is a key part for ensuring normal operating of aira. stress and beforehand close quantum of helix torsion spring of rectangle section is educed by some conclusions of mechanics of materials and compute formula

    該彈簧是保證調整臂正常工作的關鍵件，本文從材料力學的結論出發，詳盡地推導了該彈簧應力及其初始預緊量的設置，並給出它們的計算公式。
  8. The method is as follows : calculating the length, angles and coordinates of pre - cast hollow slab in cartesian coordinate system, and then adjusting the width of hollow slab beams and length of cantilever boards to make the linear cantilever slabs close to the transition of mute

    具體方法是：採用直角坐標系計算預制空心板斜長、首尾夾角和起終點坐標，根據計算結果與路線線形之差，多次調整空心板梁的梁板寬度和懸臂長度，使外懸臂折線滿足路線的緩和曲線線形。
  9. The function of the control arm is preventing rotation of the adjustment mechanism relative to the actuator

    控制臂的功能是在於阻止調整裝置相對傳動裝置做旋轉運動
  10. Optimization design of the adjusting device for automatic clearance adjusting lever of air brake

    氣制動器間隙自動調整臂調整機構的優化設計
  11. Adjust the required embedding depth by tuning the embedding legs and / or the depth wheels height

    通過調整掩埋臂或控制輪調整掩埋深度。
  12. Then the behavior of the free joint when we bring the periodic perturbation through controlling the actuated joint is analysed, we can find in the result that the behavior of the free joint in the phase plane follows an ordered closed trajectory with the center equilibrium point + 2 in the case where the amplitude of the input is small, we can define a weakening factor to make the position of the free joint reach the center equilibrium point + 2

    通過相平面分析的方法分析了當驅動臂施加周期擾動對非驅動臂運動的影響，其結論為通過調整驅動臂周期擾動的幅度及極性，可以使非驅動臂沿著圍繞平衡點2的極限環軌跡運動。在此基礎上，提出衰減因子的概念，通過衰減因子調整驅動臂擾動的幅度和周期，使非驅動臂能夠穩定在平衡點2 。
  13. According to the abrasion of brake shoe, an abrasion indicator is designed which works based on the auto - interruption regulating arm

    針對制動蹄片的磨損，本論文設計了一種工作在自動間隙調整臂基礎上的制動蹄片磨損傳感器。
  14. The results are important for dam base excavation and engineering disposal. ( 2 ) arch dam can be regarded as an elastic ground cantilever system composed of vertical cantilever, horizontal arch, and torsion structures. the dissertation takes the arch dam as load diversion system of arch - cantilevers system located on the ground composed of elastic cantilever

    （ 2 ）將拱壩虛擬為由座落在壩基塊體有限元上的一系列懸臂梁與水平拱組成，將懸臂梁視作由水平拱所支承的彈性地基梁，考慮徑向和切向調整，比以往的彈性地基梁只考慮徑向調整有所發展；而且用塊體元模擬壩基，也能較精確地模擬壩基多種斷裂構造等對壩體結構行為的影響。
  15. If the zero mark on the dial does not line up with the red jewel, adjust the height of the arm rest so that the mark and jewel do line up

    若鈕上的零標示並沒有對到紅寶石，調整唱臂架的高度使得兩者對齊[這我不清楚，要看到唱臂才會知道是什麼，可能是紅色的刻度吧] 。
  16. Usting arm assembly

    調整臂總成
  17. This article analyses our country developmental states and distance with other country about s - projecting wheeding - drum braker

    分析了我國s形凸輪制動間隙自動調整臂發展的現狀以及與國外的差距。
  18. This dissertation presents a design of auto - interruption regulating arm based on the principle of clearance sensing, which can keep every break clearance at the same fixed value

    制動間隙自動調整臂能夠在汽車制動的過程中使各制動器制動間隙都保持在同一設定值。
  19. In the concrete implementation work, a lot of areas have made in varying degrees progress ; langfang, hebei province has overcome the financial difficulty in the building - up work of rural station, has designed the unified design, and already built up 8 simple stations, every job is going on without any confusion at present ; zhejiang province brings the rural station of passenger traffic into the unified planning of rural highway construction reconstruct, implementing in step, and tried the integrated development model of public transit in urban and rural areas actively ; kailu country of inner mongolia has defined the thinking of development of building road later, opening the traffic first and then perfecting, let the numerous of peasants and herdsmen enjoy convenient first

    據介紹，為滿足各地越來越嚴格的汽車排放標準，此次展示的幾種江淮底盤新品選用日產康明斯以及錫柴最新型發動機，排放標準達歐歐。針對公交市場開發的底盤，設計為一級踏步的超低地板在一些公路客車底盤上，配有空氣懸架自動調整臂進口總成件等。針對交通部實施的「村村通」工程，江淮公司推出經濟型客車底盤，該車維護費用低，便於修理，配件便宜。
  20. In summarize, article bring forward necessary of research of the s - projecting wheeding - drum braker from three aspects : 1 need of automobile rule of law ; 2 need of automobile technology development ; 3 need that consumer request high auto - braking capability

    本文在概述里從以下三各方面提出了對s形凸輪制動間隙自動調整臂進行研究的必要性： 1汽車法規的要求； 2汽車技術發展的要求； 3用戶求追求高汽車制動性能的要求。
分享友人
分享到 Line

分享到臉書