調時螺絲 的英文怎麼說

中文拼音 [diàoshíluósī]
調時螺絲 英文
timing screws
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 時 : shí］Ⅰ名1 （比較長的一段時間）time; times; days:當時at that time; in those days; 古時 ancient tim...
  • 螺 : 1. [動物學] （軟體動物） spiral shell; snail; conch 2. （螺旋形的指紋） whorl （in fingerprint）
  • 螺絲 : [口語] screw螺絲把 key screw; 螺絲扳手 monkey spanner; screw; 螺絲刀 screw driver; screw driver b...
  1. Adjusting floor installation by adjusting any one of the four screw eyes must loosen the screws and adjust the below bracket

    地板安裝調節時必須將地板四角小螺絲擰下后在下部支架上進行調節
  2. Remove the throat plate, loosen hook screw 6 and adjust the hook

    調整旋梭時，請卸下針板，擰松旋梭固定螺絲6 ，然後進行調整。
  3. Temperature kits : contact must be properly fixed in the evaporator export pipelines, real - time communication evaporator components to temperature degrees, the material will be filled through interlinked capillary pressure due to the expansion of corrugated boxes ; swelling corrugated boxes on the pressure for change in the thrust pole with an adjustment screw and spring - loaded ball - type valves to adjust the resistance of the degrees of refrigeration volume precision adjustments

    感溫包：是必須妥善接觸固定在蒸發器的出口管道上，感知蒸發器實時回氣溫度的部件，它將充填物質的熱脹冷縮壓力通過相通的毛細管提供給膨脹波紋箱；膨脹波紋箱依據壓力的變化推動推力桿結合過熱度調整螺絲和彈簧的阻力來調整球型閥的開度，實現製冷量的精確調整。
  4. Remove compression from spring by turning adjusting screw ( 1 ) counterclockwise

    通過反時針方向旋轉調節螺絲（ 1 ）從彈簧上拆卸壓縮件。
  5. To increase the reduced pressure, turn the adjusting screw clockwise - opposite to decrease the reduced pressure

    增加減少的壓力，順時針方向旋轉調節螺絲；相反則是減少減少的壓力。
  6. To be individually adjusted at any time, and the integrated leds provide information about the switching status

    調節螺絲可以在任意時間個別地調節開關點。集成的led則提供了開關狀態的信息。
  7. 2. the rollers cha be used to adjust the workpiece before grinding. 3. when during heavy grinding, use screw pressure for firm holding as shown in the picture

    3 .磨削量較大時，可通過調整壓桿螺絲保證滾輪壓臂壓持牢固
  8. 3, in the test, placing screw of compensator shall be appropriately adjusted to make it convenient for compensation

    3在試行時，應將補償器限位螺絲作適當調整，便於產品伸長和壓縮。
分享友人
分享到 Line

分享到臉書