豎桿機 的英文怎麼說
中文拼音 [shùgǎnjī]
豎桿機
英文
post driver-
It is made up of the melting shaft furnace, titled holding furnace, ( reverberatory refining furnace ), casting machine, automatic shearer, cast bar straightening and dege shaving machine, rolling mill, engine oil lubrication system, emulsion lubrication system, rod orbital coiler, line electric control, etc
銅桿連鑄連軋機生產線主要有融化豎爐，傾動式保溫爐， （銅精煉反射爐） ，連鑄機，滾剪機，校直刨邊機，打毛機，連軋機，潤滑油系統，乳化液系統，銅桿還原冷卻裝置，雙筐梅花收桿機和電氣控制系統等組成。It ' s an ideal structural system and has multi - earthquake resistance ability because of a great deal of slabs removed in floors above the transfer - story amended the lateral stiffness of the stories near the transfer - story. based on the available references, the five - spring line element, the three - spring line element and the multiple vertical - line - element model are introduced to model special column, beam and shear - wall, the relevant stiffness matrixes are deduced and the restoring - force models are gaven to deep into the elasto - plastic seismic characteristics of the structure. acording to the results of shaking table test and elastic finite element analysis, a new making model melhod is presented in which uses the linear and the nonlinear element and the assumption that the floor is infinitely rigid in different areas
為進一步研究這種復雜高層建築結構的彈塑性性能，本文在國內外現有研究的基礎上，提出利用五彈簧桿元、三彈簧桿元及多豎線單元模型分別模擬空間柱、梁和剪力墻，推導了相應的剛度矩陣並給出了恢復力模型；結合試驗研究和精細有限元分析的結論，提出線性和非線性單元相結合，剛性樓板假定和彈性樓板相結合的建模方法，較好地解決了空間結構彈塑性分析中佔用計算機資源較多的問題；接力大型有限元分析程序? ? ansys ，在上述建模思路的指導下建立了結構的空間非線性分析模型，進行了空間三維彈塑性時程分析。Safety of unshielded tunnel boring machines and rodless shaft boring machines for rock ; german version en 815 : 1996
無防護平巷掘進機和插入巖石的無鉆桿豎井鉆機的安全Abstract : in this paper, the method of the impulse torques control is established for vertical planar two - link flexible manipulators on the basis of rigid manipulators control. the variables of two - link manipulators are restrained when the tip trajectory of manipulator is being tracked with this method. finally, the results of numerical emulation and experiment are shown in the paper
文摘:在剛性雙連桿機械臂控制方案的基礎上，提出了柔性雙連桿機械臂的軌跡跟蹤和振動抑制的脈沖力矩控制方案，針對豎直平面雙連桿柔性機械臂進行了數值模擬和實驗研究。Thanks to its light weight, itsave time, manpower and equipment during the installation process. itean be erected by a crew of only twoor three people without need for crane or hoist, greatly reducing traffic diversion and resultant costs
因桿身質輕，安裝過程中省時、省力、省設備，只需兩、三個人就可以使燈桿豎起來，不需要吊車或起重機安裝費用低，對交通影響小。At the same time it has the shortcoming of complex mechanics analysis. in this thesis we mainly discuss the structure behaviors of the mega structure. firstly considering the differences between mega - frame and normal - frame, that is the influence of rigid zone and shearing type deformation are considered. a computer program for calculation of mega - frame structures based on element stiffness matrix to members with rigid zone considering shearing type deformation has been written and some of mega - frames have been calculated by using the program
首先，根據巨型框架與普通框架的主要區別，採用帶剛域桿件考慮剪切變形時的桿單元模型，利用fortran語言編制了巨型框架結構線彈性有限元靜力分析程序，並利用該程序對多個巨型框架結構進行了計算，分析了巨型框架結構的靜力性能，深入研究了結構在豎向荷載和水平荷載作用下的傳力機理、力學特性和變形特點。The paper also compared lfswsums with fsmrcss on aseismatic property. secondly, the paper created compute model of space beam system constructure on the fsmrcss, and studied stress distribution in fsmrcwb under vertical loads and under elastic earthquake force with constant vertical loads respectively
其次，建立了該結構體系的空間桿系結構的計算模型，對結構應力分佈及墻梁的受力機理進行了分析，研究了結構在豎向荷載與小震水平地震作用下的應力分佈。分享友人