超細砂 的英文怎麼說
中文拼音 [chāoxìshā]
超細砂
英文
superfine sand-
Investigation on agglomerate mechanism of quartz sand ultra - fine comminution
石英砂超細粉碎的團聚機理與抑制方法的研究The expansion agents can only make up the shrinkage to some extent, and the compensation effects would be reduced when the retardener and fly - ash are used. the expansion agents are not panaceas to avoid the shrinkage cracking as expansion can also reduce the concrete soundness. under bad curing condition, the polypropylene fibrillated film fiber can improve concrete ' s anti - crarking property, while the nominal steels have very unobvious effects. to reduce the concrete shrinkage thus avoid the cracking, the former factors must all be taken into account in concrete proportion design to develop sound concrete
研究結果表明，水泥的品種和用量是影響混凝土收縮值的主要因素之一，當混凝土中水泥用量超過470kg / m ~ 3時，混凝土的收縮值超過400 10 ~ （ - 6 ） ，在約束狀態下存在高開裂風險；採用細砂使混凝土單位用水量顯著提高，收縮值也大幅增加；優質粉煤灰總體上能抑制混凝土的收縮，以超量方式摻入其抑制作用更加明顯，但粉煤灰混凝土早期的粘聚性較差，應注意養護，以免失水產生龜裂；早強減水劑和緩凝減水劑都會使混凝土收縮值增加；膨脹劑只能補償混凝土部分收縮，同時受緩凝劑和粉煤灰的抑制，而且膨脹使混凝土的體積安定性增加了不確定因素，膨脹劑不是解決混凝土收縮裂縫的良方。The research is to develop a new material - - - - high performance concrete of hill sand on the basis of practice of high strength concrete of hill sand and knowledge of ultra - fine trass additive by using concrete material in guizhou and mixing fly ash. the research result shows that the flowability, moldability, cohesiveness of high performance concrete of hill sand are significant by comparison with ordinary concrete on mechanical properties, long term properties, and durability
本研究課題是在已成功研製並實際應用的c60高強山砂混凝土的基礎上，結合對微細（超細）活性摻合料性質的理論認識，充分利用貴州當地的混凝土材料，並摻入微細（超細）活性摻合料，研製一種新型的高性能混凝土，即山砂高性能混凝土。We use astmc1202 - 94 rapid testing method of chloride permeability to testify the cement mortar, in which we add ultra - fined mineral functional material
採用astmc1202 - 94的快速氯離子滲透法對摻入超細礦物功能材料的水泥砂武漢理工大學碩士論文漿、水泥混凝土的氯離子滲透性進行了測定。The results show that, when increasing the feed rate of the grinding wheel, decreasing the rotating speed of the wafer chuck table and using coarser grit grinding wheel, the material removal rate in the wafer rotating grinding increase, the feed rate of the grinding wheel has greater influence on the material removal rate ; when suitably increasing the rotating speed of the grinding wheel, decreasing the feed rate of the grinding wheel and using finer grit grinding wheel, the wafer surface roughness can be reduced ; there exists a critical rotating speed of the grinding wheel ( about 2300rpm ), beyond which the material removal rate evidently decreases and the spindle motor current and wafer surface roughness steeply increase ; when the grit size of the grinding wheel is finer than # 2000, the material removal rate decreases and the wafer surface roughness has no obvious improvement
研究結果表明，增大砂輪軸向進給速度和減小工件轉速，採用粗粒度砂輪有利於提高磨削矽片的材料去除率，砂輪軸向進給速度對材料去除率的影響最為顯著；適當增大砂輪轉速，減小砂輪軸向進給速度，採用細粒度砂輪可以減小磨削表面粗糙度；在其它條件一定的情況下，砂輪速度超過一定值會導致材料去除率減小，主軸電機電流急劇增大，表面粗糙度變差；採用比# 2000粒度更細的砂輪磨削時，材料去除率減小，矽片表面粗糙度沒有明顯改善。分享友人