跟蹤軸 的英文怎麼說

中文拼音 [gēnzōngzhóu]
跟蹤軸 英文
tracking axis
  • 跟 : Ⅰ名詞（腳的後部或鞋襪 的後部） heel Ⅱ動詞1 （在後面緊接著行動） follow 2 （指嫁給某人） be marrie...
  • 蹤 : 名詞（腳印; 蹤跡） footprint; track; trace; trail
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 跟蹤 : follow the tracks of; tail after; following; follow up tracing; track; tracking; trail; lock on; ...
  1. There are not only beam - slanting but also large blind zone near the zenith in the two - axes radar used in the present

    現有的艦載兩軸雷達由於受到船搖的影響，不僅波束傾斜，而且天頂附近有很大的跟蹤盲區。
  2. So it is necessary to study the driving structure and control scheme of new system radar in order to track continuously in whole hemisphere without blind zone

    因此，研究新體制的三軸雷達的驅動結構及控制方案以實現大於半球的全空域無縫隙連續跟蹤就變得十分必要。
  3. Thirdly, in the light of the demands ' that the large - scale photoelectric tracking and sighting equipment now available ask for fsm and the specific demands of the fast - steering mirror, designs a set of shaftless rapid controlling reflector system which impels manufacturing enterprises to bourgeon a suit of new productive processing method which differentiate completely from that of the axiferous fast - steering mirror system

    由現有大型光電跟蹤、瞄準設備對fsm的要求，結合對快速控制反射鏡結構的具體要求，自行設計了一套完全區別于有軸系支承的新的生產加工工藝的柔性軸快速控制反射鏡系統。
  4. The subject for different process technology and surface treatment of crank takes tracking checkout for its internal stress, analyses relation of jumping measurement, deformation measurement, recovery measurement and stress change, finds the reason and usual law of jumping overproof of crank. through cold pressure alignment, hot pressure alignment, support aged alignment and so on methods for 42crmo steel crank, the subject checks change of stress in the process of alignment and change of tissue and property after alignment for crank, and gives comprehensive evaluation for every alignment technology, then give safe and feasible technology parameter

    本課題主要是對不同加工工藝及不同表面處理過程的曲軸，對其內應力進行跟蹤檢測，分析各工藝過程中跳動量、變形量、恢復量與應力改變的關系，找出曲軸跳動量超差的原因和一般規律。通過對42crmo鋼曲軸進行「常溫壓力校直」 、 「熱壓力校直」 、 「支撐時效校直」等方法的校直，檢測校直過程中曲軸應力的變化及校直后組織和性能的改變，進而對各校直工藝進行綜合評價，給出安全可行的工藝參數。
  5. Because of the change of ship attitude ( rolling angle r, pitch angle p and course angle h ) led by ship rocked interference and windage, the los stabilization will be influenced obviously

    由於艦船的艏搖、縱搖、橫搖等引起艦船姿態的變化以及風阻力矩的作用，對跟蹤系統的視軸穩定性產生明顯影響。
  6. Camera tracking axis

    攝象機跟蹤軸
  7. When the atp system is setup on a moving bed, movement and angular jitter of the bed will cause system line - of - sight high frequency jitter

    當捕獲、跟蹤與瞄準系統安裝于運動平臺上時，運動平臺的運動及抖動將導致系統視軸存在高頻的抖動。
  8. In the past 21 years dalian office finished more than 120 projects all over north - east in the field of microelectronic, optical fiber and cable, lcd, biological and pharmaceutical, mechanic, assembly, steel, ship manufacturing and domestic buildings. some of the projects got the prize from national or provincial construction department. below are the reference projects dalian office finished these years : dalian dongfu lcd co., ltd, dalian haire industry park, guangyang bearings dalian co., ltd, konica dalian co., ltd, canon dalian office appliance co., ltd, pacifica electronics co., ltd, photoelectron dalian co., ltd, hyundai electronics dalian, rhi dalian co., ltd, yuanda pharmaceutical co., ltd, siemens vdo auto electronics changchun, toyota tianjin precise products co., ltd 6000, toyota zhangjiagang technology co., ltd, shenyang sico semiconductor co., ltd, dalian dongxian and dalian orient precise products co., ltd. dalian office will carry the principle make best design, provide satisfying service to provide our best service to the clients

    Edri大連分院成立至今完成120多項工程設計監理及工程總承包項目，其中多個項目工程設計獲得國家和部省級科技進步獎，先後完成了大連東福彩色液晶顯示器工程大連海爾工業園光洋軸承大連有限公司柯尼卡大連有限公司佳能辦公設備大連有限公司太平洋電子有限公司光電子大連有限公司現代電子大連有限公司奧鎂大連有限公司，大連高新生物制藥有限公司大連保稅區國際車城遠大制藥有限公司西門子威迪歐汽車電子長春有限公司豐田合成天津精密製品有限公司豐田合成張家港科技有限公司，沈陽科希-硅技半導體技術第一有限公司大連東顯電子有限公司大連東方精工有限公司等一大批高科技產業園區設計項目，並且進行全程質量跟蹤服務，在業內樹立起edri大連分院良好口碑，贏得了客戶廣泛好評，為我院在東北地區的發展做出了自己的貢獻。
  9. With the development of tracking and pointing system these years, the requirement of line of sight ( los ) stabilization of tv tracker becomes more and more strict

    近年來，隨著對武器跟蹤系統要求的不斷提高，對電視跟蹤儀的的視軸穩定的要求也日趨嚴格。
  10. Experimental and simulation researches are implemented on basic concepts, key unit technologies of line - of - sight stabilization of acquisition, tracking and pointing ( atp ) system on moving bed. system simulation gives the complete system performance estimations

    針對運動平臺捕獲、跟蹤與瞄準系統視軸穩定技術的基本概念、關鍵單元技術進行了實驗和模擬兩方面的工作，以模擬的形式對系統的最終性能給出了預估。
  11. In two axis system, a circle interpolator is designed, and a new method based on ga - neural networks is proposed to adjust pid parameters online to reduce the tracking error. then, an integrated controller based on rbf neural network ( rbfnn ) is designed to reduce the contouring error of the two axis. experimental results show that the proposed integrated controller significantly improved accuracy in both tracking and contouring

    對于雙軸系統設計了一個軌跡為圓的插補器，採用基於遺傳演算法?神經網路的在線pid參數調整演算法，減小了系統的跟蹤誤差，並分析雙軸之間的輪廓誤差，設計出基於rbf神經網路的綜合控制器，經過模擬實驗證明，本文採用的綜合控制器能有效地減小系統的跟蹤誤差和輪廓誤差，提高系統的控制精度。
  12. Beam riding systems use a target tracker whose purpose is to maintain the antenna boresight pointing at the centre of the reflecting area of the target.

    波束制導系統使用一個目標跟蹤裝置，它的目的是保持天線視軸指向目標反射的中心。
  13. In many performance check, artillery control systematic dynamic trail aimed error is one of relatively important parameter, dynamic trail aimed error denote : when high cannon system is dynamic trailing, set bullet pellet flight time is 0, in the condition of not considering advance quantity ( 0 fly working ), the axis of artillery pipe should direct goal

    在諸多的性能考核中，火控系統的動態跟蹤瞄準誤差是較為重要的參數之一。所謂動態跟蹤瞄準誤差是指：當高炮系統在進行動態跟蹤時，設定彈丸飛行時間為零，即在不帶提前量的條件下（即零飛工作方式下） ，火炮身管的軸線應直接指向目標。
  14. On the analyzing of the technology trend, a plan of developing a multifunctional mark printer is brought forward the procedure of the development of a multifunctional mark printer is detailed in this thesis. a interface - card and a photoelectric board is designed, a control circuit is assembled by using them, through which a computer can control the mark printer ; a mark printer driver is developed by using com technology ; the mechanical part of the mark printer is designed by imitating milling machine ; a database software for components management is developed for high - speed train bearing industry. the managements include the registering for components, unique mark printing on components and analyzing of useful parameters. the user can complete the lifetime tracing for a component expediently

    設計介面卡和光電隔離放大電路，組成了電機控制和抬筆控制電路，通過它們pc機可以控制標號印表機工作；採用組件化技術開發了標號印表機控制軟體，驅動標號印表機工作；參考刻模銑床原理，設計了機械部分；針對高速客車軸承廠，開發了零件標號管理軟體，使標號列印和信息管理系統有機結合起來，達到在登記零件信息的同時，自動列印零件的標號，方便了對零件的跟蹤管理。
  15. The influence of swinging ship to los is analyzed in detail. the tracking precision of the shipborne tv tracker will be improved greatly when the feedforward signal otship swaying is measured by rate gyro

    本文詳細分析了艦船搖擺對視軸穩定的影響，通過理論推導和模擬分析論證了採用速率陀螺測量並前饋艦船搖速度信號將極大的提高艦載電視跟蹤儀的跟蹤精度。
  16. The fast - steering mirror is a device used to control the direction of light beam accurately, with great inertia mechanical structure, form a compound shaft tracking system which apply to drive and stabilize the light beam

    快速控制反射鏡是採用反射鏡面精確控制光束方向的一種裝置，與大慣量機架結構的主系統共同構成復合軸跟蹤系統，在各種光學系統中用於對準和穩定光束。
  17. And so on, the mathematical model and transfer function of the tracking system are built, and the feasibility of the tracking control system design is demonstrated. furthermore, the static error of the system with a unit incline input is deduced. a majority of model of unit is based on analytics, so the general model can apply to other optical intersatellite communications systems

    在此基礎上，將atp跟蹤控制子系統視為線性定常系統，通過解析法和實驗法對子系統的各個控制環節的單元器件進行合理建模，得出整個環路總的開環及閉環傳遞函數，論證了本課題所設計的atp跟蹤控制環路的可行性及其視軸輸入為斜坡信號時的理論穩態誤差。
  18. Length, diameter, density, fresh weight, dry weight, water content, osmotic potential and element concentrations ( ca, mg, na, k, cl ) were determined for each. seedling of b. gymnorrhiza and a. corniculatum were cultured for 60 days on various salinity of seawater ( 0, 5, 10, 15, 20, 30, 40, 50 ) in green house. samples were taken at 3, 7, 11, 15, 22, 30, 45 and 60 days after planting, separated into root, hypocotyl, stem and leaf

    本文研究了福建九龍江口木欖和桐花樹胎生繁殖體從果實形成到發育成熟過程中形態、生物量、含水量、胚軸密度、滲透勢、五種主要礦質元素（ ca 、 mg 、 na 、 k 、 cl ）等的變化和溫室內人工鹽度梯度栽培下木欖和桐花樹成熟繁殖體長成幼苗（ 0 60d ）過程中形態、生物量、含水量、滲透勢、光合蒸騰特性、五種主要礦質元素（ ca 、 mg 、 na 、 k 、 cl ）等的變化；並且在野外自然條件下，跟蹤調查不同灘塗位置下秋茄成熟繁殖體定居成活、自然死亡狀況以及測定幼苗生長過程中（ 1年）形態、生物量、含水量、光合蒸騰特性等的變化。
  19. The assignment of the load of the steam turbine can be solved by the reverse follow, the assignment of the load of the boiler can be solved by dsfd

    根據兩種規劃問題的特點，汽輪機系統負荷分配問題採用分枝限界反向跟蹤的優化演算法來求解，鍋爐系統負荷分配問題採用轉動坐標軸直接搜索可行方向法（ dsfd法）來求解。
  20. In this dissertation, the development survey, research actualities and application prospect of vamt are introduced at first, and the models of kinematics, dynamics and linear motor servo are analyzed then. currently the dynamics model is complex or established mechanically, which restricts the study of control theories. thus this dissertation present a simple and easy - realized control idea, namely, the fore and torque of every leg determined by the inverse - solution of mechanics are regarded as changeable load force ( disturbance ) applied in motor, the elongation of the leg or displacement of sliding is regarded as the output of linear servo system

    本文首先介紹了虛擬軸機床的發展概況、研究現狀和應用前景，然後對其運動學、動力學、直線伺服系統模型進行分析，針對目前動力學模型過于復雜或完全從機構學角度建立不便於控制的問題，提出了簡單、易於實現的控制思想，即將虛擬軸機床的動力學方程反解所確定的各桿受力（矩）視為電機的可變負載力，以桿長伸縮量或滑塊位移為伺服系統輸出，從此構成位置閉壞，實現軌跡跟蹤控制。
分享友人
分享到 Line

分享到臉書