路元件 的英文怎麼說
中文拼音 [lùyuánjiàn]
路元件
英文
circuit component-
The electrical connector of an active circuit component
有源電路元件的電接頭。We now take digital circuit approaches to realize the algorithms, i. e. using microprocessor to calculate harmonic components. so as to overcome disadvantages of analogy circuits, for example, instable circuit parameters, low calculation accuracy, inconvenient regulation and low integration level
在演算法實現上,採用數字方式,即採用微處理器進行數值計算,克服了模擬電路元件參數不穩定、計算精度差、調節不方便和集成度低等缺點。All of its circuit elements are bonded together rather than separately wired to each other after being manufactured.
它所有的電路元件製成后都接合在一起,而不是用導線分別相互連接。A passive circuit element
中性的電路元件A generic term for a circuit element that can be turned on or off in response to one or more control signals
一種泛指電路元件的術語,通過響應一個或多個控制信號便可以開通或關斷這種電路元(件) 。Pspice models for fcg, pulse transformer, electric exploding wire opening switch ( eeos ), blumlein pulse forming line, and virtual cathode osillator ( vircator ) are created
利用pspice程序,創建了包括脈沖變壓器、電爆炸絲( eeos ) 、 blumlein傳輸線、虛陰極振蕩器( vircator )和fcg等在內的電路元件模型庫。Inservice inspections for primary circuit components of light water reactors ; hydrotest
輕水反應堆初級電路元件使用中的檢驗.第3部分:耐壓試These passive circuit elements, as they are often called, are of three main types.
通常所說的無源電路元件有三種主要類型。For bus system installation, the focus is put on cable selection principle, installation process and antinoise measure ; for security protection equipment installation, the intrinsic safety concept, installation method equipment selection and installation under two electric power supply modes ( entity concept and fisco model ) and the bus system protection against surge voltage are illustrated ; for network component installation, the selecting, installing and integrating methods of general purpose terminators, repeaters, link equipment, bus power supply and impedance module are described
在總線電纜的安裝方面,著重討論了電纜的選型原則、安裝方法和抗噪防擾措施;在安全保護設備安裝方面,介紹了總線系統中本質安全的概念、安裝方法、兩種供電方式(實體概念和fisco模型)下設備的選擇與安裝以及總線系統浪涌電壓的保護和設備安裝方法;在網路元件的安裝方面,主要列舉了通用終端器、中繼器、鏈路設備、總線電源及其阻抗模塊等的選擇、安裝和集成方法,為總線系統的安裝提供了可以借鑒的實用經驗。Study of two - port electric network element set
二埠電網路元件體系研究Researches in component values and chaotic waves of lorenz circuits
羅侖茲混沌電路元件值與混沌圖形研究A unit bearing circuit components which can be plugged into a piece of equipment
一種裝有電路元件的插件板,可將它插入設備中。Capacitor is a basic circuit component and widely used in the electronic equipments and electrical engineering fields
電容器是一種基本的電路元件,被廣泛地應用於電子設備與電氣工程等領域。An arrangement of components in a circuit that splits the current into two or more paths. used chiefly in the phrase in parallel
並聯一種把電流分成兩條或多條通路的聯接電路元件的方法。常用於短語inparallel中Based on the analysis of the working principles and the circuit features of the air - condition controller, the circuit is described by the logic signal, and according to the fault features of the components and some rules the number of sample is decided
在系統的分析了空調控制櫃的工作原理和電路特點的基礎上,選擇了電路的通斷信號對電路狀態進行描述,並根據電路元件的故障特點和一定的原則確定了采樣點數目。The spice simulation confirms the attractive properties of the proposed circuits. the simulative circuits of active network elements, analog signal operation and inductors based on current conveyors are systematically researched. a new active floating inductor is proposed
系統地研究了電流傳送器在有源網路元件模擬、模擬信號運算和電感模擬電路中的應用,提出了一種基於電流傳送器的新型模擬浮地電感。Transmission and multiplexing - multiplex section protection information model for the network element view ; english version ets 300413 : 1995
傳輸和多路復用.網路元件檢查用多路復用段保護信息模The 6psd30 - 1 fuel injection pump test stand is the 1970 ' s product and leave unused. its electrical control part is made up of large discrete components with low - test sensitivity, inconvenient setting and adjustment, high trouble rate. moreover, its circuit components are aging and spoiled
6psd30 - 1型電子控制噴油泵試驗臺是七十年代的產品,其電氣控制部分電路採用大量分立元件構成,測試靈敏度低,設定調整不方便,故障率高,而且電路元件大多老化、損壞,現處于閑置狀態。Standard test method for determining current carrying capacity of a conductor as part of a membrane switch circuit
測定薄膜開關線路元件導體載流能力的標準試驗方法Then the author gives the primary circuit and its protect circuit design method of the fcl, and obtains primary circuit parameters of an fcl test prototype ( 380v / 200a ) and an fcl industry prototype ( 10kv / 500a ) by this means
第三章給出了固態限流器主電路元件參數的計算方法,包括限流電感設計、旁路電感計算、橋電路及其均壓保護電路設計等。分享友人