軋機生產率 的英文怎麼說

中文拼音 [yàjīshēngchǎnlǜ]
軋機生產率 英文
mill production output
  • 軋 : 軋動詞[方言]1 （擠） press hard against each other; push against2 （結交） associate with; make f...
  • 機 : machineengine
  • 生 : Ⅰ動詞1 （生育; 生殖） give birth to; bear 2 （出生） be born 3 （生長） grow 4 （生存; 活） live;...
  • 產 : Ⅰ動詞1 （人或動物的幼體從母體中分離出來） give birth to; be delivered of; breed 2 （創造財富; 生...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 生產率 : productivity; output; efficiency; efficacy; production coefficient; production rate生產率比 produ...
  • 生產 : 1 （使用工具創造生產、生活資料） produce; manufacture 2 （生孩子） give birth to a child; childbi...
  1. Rolling - cutting biscuit shaping machine is new equipment of making soda biscuit, good toughness of thin biscuit and super - thin biscuit. it ' s high production efficiency, low noises, safe operation, convenient, beautiful outer shape. this machine can press and roll rough flour 3 times and equiped with remaining flour recycling machine, also equiped with double - rolling cutting shaped equipement, in the mean time, it can produce two biscuit embryo of differnt shape. 3 times pressing - rolling machine can adjust different thickness and biscuit rough surface. it can roll rough flour and do not stick to rough flour embryo, correctness rate of adopting mould to cut margin of flour embryo reaches 100 percent so that avoid deforming of embryo due to deviation. this machine is one equipment which adopting advanced and won first technical rewarding for its independently control operation, beautiful outer appearance

    滾切式餅干成型機是連續製作梳打餅、韌性和薄餅超薄餅的新型設備，具有生產效率高、噪音低，操作安全、方便，外型美觀等優點，本機具有三道軋輥制皮和余料回收機，配備雙滾切成型裝置，同時能生產兩種不同形狀的餅干胚不停機，三道軋輥能同時調節不同厚度和餅皮具有軋輥不粘皮、採用印模切邊一次同步進行準確率100 % ，避免偏差而造成餅胚變形，該機具有獨立控制操作，外形美觀，是目前國內較先進而獲得技術一等獎的設備。
  2. It can improve minus deviation rolling rate greatly, assure the quality of product and increase the benefit, so it is used widely in steel rolling

    採用這種軋機可以大幅度提高負偏差軋制率，穩定產品質量，提高經濟效益，因而被廣泛用於軋鋼生產中。
  3. Abstract : tensile reducer is one of the necessary apparatuses during the pipe production process at present. this paper deduces a multi - variation formula by using the energy principle and adopting upper limit method. the formula can be used to calculate the parameters such as the drive power, tensile coefficient, roll speed, depth of exit pipe wall, hole type ellipse etc. the existence of minus drive power has also been theoretically calculated

    文摘:張減機是鋼管生產中不可缺少的設備之一.本文從一般能量原理出發，採用上限法推導出一個多變量公式，利用該公式可求解電機功率、張力系數、軋輥轉速、出口鋼管壁厚、孔型橢圓度等參數，並且從理論上計算出電機負功率的存在
  4. On the basis of the theory of metal distortion, this dissertation has a series of research work with bar slit rolling and combining productive practice, firstly the author has been develop the computer aided roll - pass design system for bar slit rolling in the scope of rolling. the dissertation has been designed using round steel slit rolling as entity model

    本文基於金屬塑性變形基本理論，以棒材切分軋制為研究對象，結合生產實踐進行了深入的理論研究，在軋制領域里率先開發了棒材切分軋制的計算機輔助孔型設計（ computeraidedroll - passdesign ）系統。
  5. The type of this article is " used for product ". it analyzes surface pollution of metal, hydro capacity and effect to wall piping quantitatively on the base of the rinsing of piping of hydraulic system of precise - rolling machine at the hot sequential rolling plant. by analysis, we confirm the fit flux and pressure when rinsing, design high - ability, high - efficiency, wide - applicability whole set equipment

    本論文的成果直接用於生產，以太鋼熱連軋精軋機液壓系統的鋼管清洗為背景，對金屬表面污染進行分析，對液壓鋼管沖洗時流體的性能和其對管道內壁的作用效果進行定量的分析，確定合適的沖洗流量和沖洗壓力，設計製造了能力大、效率高、效果好、適用廣的成套裝置。
  6. Consumers successively plunged a large number of silicon controlled commuted devices ( such as steel rolling 、 electrized locomotive 、 aluminium electrolysed devices etc ) and smelting devices to improve their produced efficiency or to save energy. on the one hand it is good for consumers, on the other hand it will arouse the fluctuation of voltage and frequency and it will result in the collision of the active and reactance capacity. meanwhile these nonlinear loads bring much harmonic into the electric network which deteriorate the quality of power supply and hazard the online device enormously

    用電部門為了提高生產效益、節約能源，在大電網中相繼出現了大量的可控硅整流裝置（如軋鋼、電氣化機車、鋁加工電解設備等）以及冶煉設備，這些設備的投入使用對節能有一定好處，但給電網造成有、無功沖擊，引起電壓和頻率的波動，同時，這些非線性負荷向電網注入大量諧波，大大惡化了供電系統的電能質量，給用電設備帶來了極大的危害。
分享友人
分享到 Line

分享到臉書