軋輥壓制 的英文怎麼說

中文拼音 [yàgǔnyāzhì]
軋輥壓制 英文
roll compacting
  • 軋 : 軋動詞[方言]1 （擠） press hard against each other; push against2 （結交） associate with; make f...
  • 輥 : 名詞[機械工程] （能滾動的圓柱形機件） roller
  • 壓 : 壓構詞成分。
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  1. Fictious simulation of high - speed roll casting has been carried out on the basis of the fact. the results showed that roll casting speed increase with the decrease of the thickness of the strip, and the peak value of rolling pressure decrease with the increase of roll casting speed and thickness of strip or the increase of roll casting zone. the designed parameters of mechanical capabilities of the roll caster should be raised when rolling pressure increase with roller diameter increase

    研究結果表明，減薄鑄軋板坯厚度可提高鑄軋速度；隨著鑄軋速度降低、鑄軋區增大與鑄軋坯厚度減薄，軋制壓力峰值增大；隨著鑄軋輥徑增大，軋制壓力增大，因此鑄軋機力能設計參數也要相應增大。
  2. This method can decrease the gap setting time for which the oil column of hydraulic cylinder is not retracted and there is no minute adjustment of oil column for the first several passes

    採用該方法，軋制過程液壓缸油柱不用回縮，而且前面道次液壓不進行微調，從而節省了輥縫設定時間。
  3. Theoretically the varying contact rolling technology can increase the transverse stiffness of loaded roll gap, heighten the control effect of roll bending, improve the distribution of contact force between backup roll and work roll

    從理論上分析了變接觸軋制技術在提高承載輥縫橫向剛度、增加彎輥力調控功效、改善輥間接觸壓力分佈方面的作用。
  4. Abstract : the lubricating condition of cold rolling is affected by many factors. this paper shows the relationship between the friction coefficient and three rolling parameters, such as rolling speed, reduction and concentration of rolling lubricating oil

    文摘:主要研究了在冷軋過程中，軋機輥縫摩擦系數受軋制速度、相對壓下量以及乳化液濃度因素影響的變化規律。
  5. The configuration of conventional backup and work rolls for revamped 1700 tandem cold rolling mill at wisco was proved unreasonable by systematical test as the cause of work roll edges contact during thin strip rolling and unsatisfactory flatness of product

    摘要通過現場跟蹤測試和生產實踐發現武鋼1700冷連軋機組「酸軋聯機」改造工程中存在常規凸度輥形配置方案不合理，由此引起了薄規格軋制的工作輥「壓肩」現象和軋制過程欠穩定導致成品板形質量欠佳等問題。
  6. The dried powder raw materials will be fed from the top of dry granulator, then enters into flaking machine where becomes flakiness raw material will be made into the needed granule product through the procedures of crushing, processing granule and sieving powder and so on

    乾燥后的各種乾粉物料從干法制粒機的頂部進入，經預壓進入軋片機內，在軋片機的雙輥擠壓下；物料變成了片狀、片狀物料經過破碎、整粒、篩粉等過程，得到需要的粒狀產品。
  7. According to the special characters of a multi - roll cold tandem mill, a rolling force prediction model based on fuzzy algorithm and cerebellum model articulation controller ( cmac ) combined with the traditional model was designed to improve the precision of rolling force prediction

    摘要針對寬帶鋼多輥冷連軋機組特點，為提高軋制力的預報精度，在結合傳統軋制壓力模型的基礎上把模糊演算法和神經網路有機結合，設計出基於模糊小腦模型神經網路的多輥冷連軋機軋制力預報模型。
  8. Products : 50 tons drawing dies, 100 tons punching dies, 150 tons carbide parts for diamond manufacturing, 100tons rollers, 100 tons seal rings and 150 tons other special parts

    產品方案：各種線、棒、管材控制模50噸、沖壓模具100噸、頂錘壓缸150噸、軋輥環100噸、密封環100噸、其它異形產品300噸。
  9. The work principle and identity of the press with cone - shaped roll have been introduced with expounding use of plc to control the production of such machine of which the technology and control have been based as design of the hardware and software of control system

    摘要介紹了軸向軋制的雙錐輥輾壓機的工作原理和特性，闡述應用可編程式控制制器控制雙錐輥軸向軋機的生產，並且針對其工藝和控制要求，從硬體和軟體進行了控制系統的設計。
  10. And its nnc and nni are both established with the optimal neural network. so the hydraulic bend roller system ' s dynamic response velocity and static tracking precision are advanced. hydraulic bend roller force can operate better and mill ' s dynamic characteristic is improved

    將優化網路用於液壓彎輥系統的控制中，採用內模控制方案，辨識器和控制器用優化網路來離線設計、在線調整，提高了液壓彎輥系統的動態響應速度和穩態跟蹤精度，充分發揮了液壓彎輥力對板形的調整作用，改善了軋機系統的動態特性。
  11. The results indicate that the time of press influences sawtooth distortion greatly, but infects sawtooth less. root of the sawtooth made by the method of static simulating rolling have no changes hardly, and from the upper distance the changes became, then on the top the sawtooth curves to the opposite direction

    結果表明：壓制時間對齒形的變形影響較大，對齒型的影響很小；模擬軋輥壓制的鋸齒，根部一段幾乎沒有變化，是從一段距離開始變形，然後在頂端向相反的方向彎曲；壓製成型后，鋁板厚度的變化很小。
  12. In the special fields materials, semiautomatic, strapping equipment or beyond that with manufacturing, equipment, plastic as well as with mechanical engineering, strapping and / or with filling and packaging is unipack, servis obalove techniky well - known

    針對衛生紙、折邊處理、壓花、滾花以及輸紙輪、制紙軋輥、紙張加工、折邊工作的報價會引起您的興趣。
  13. In the special fields toilet paper, toilet paper, embossed or beyond that with semiautomatic, processing machine, punching as well as with folding, tissue and / or with paper processing and embossing is dongguan jiaming machine building co., ltd. well - known

    針對衛生紙、折邊處理、壓花、滾花以及輸紙輪、制紙軋輥、紙張加工、折邊工作的報價會引起您的興趣。
分享友人
分享到 Line

分享到臉書