軟體模型化 的英文怎麼說
中文拼音 [ruǎntǐmóxínghuà]
軟體模型化
英文
software modularity-
First, the theory of fretting wear and studies on fretting fatigue were introduced and the parametric method was used in the process of creating the model of dovetail joints in ug software. the elastic contact problem is analyzed in finite element method ( fem ) and is used to the parameters " distribution and contact stress of the joint are obtained on the base of ansys code. with the effect factor of load frequency, the prediction method of fretting fatigue life of dovetail joint under low and high / low cycle complex load is proposed
本文介紹了微動損傷的機理和微動疲勞壽命的研究方法；利用ug軟體對燕尾榫聯接結構創建了參數化實體模型；基於ansys軟體平臺求解彈性接觸問題，獲得了榫聯接結構接觸應力及接觸狀態量的分佈；在已有微動疲勞壽命預測模型的基礎上，引入載荷頻率影響因子，對低周、高低周復合載荷作用下的燕尾榫聯接結構進行了微動疲勞壽命的預測，與試驗結果對比表明採用本文提出的方法預測榫聯接結構的微動疲勞壽命是有效的。In this paper, pro / engineer is used to creat the model of wheel which is according with gb / t3487 - 1996. then the model is submitted to ansys where it is dealed with and loaded according as the prescribe in the fatigue experiment of gb / t3487 - 1996 and is analyzed in intension. the result shows the maximal stress is much less than the breaking point of aluminium alloy, which makes material wasted
本文使用pro / engineer軟體，按照輪輞的國家標準，建構車輪的實體模型；然後把模型導入ansys ，按1997年中國汽車行業標準中的汽車輕合金車輪的性能要求和實驗方法所規定的疲勞實驗要求施加荷載；然後進行強度分析，分析結果表明，車輪的最大應力遠小於鋁合金的許用應力，存在進一步優化的可能和必要。Based on the theory of piecewise - linear, the paper carries through the research of model self - adaptive control to electric arc - furnace electrode regulator system ( eafers ), and the digital self - adaptive control law of reference model is deduced. then, we designed the software simulation system of eafers according to the law, though which we studied the character of eafers. finally, a set of physical model of eafers, which is realized by hardware circuit, is designed according to the former research
本文首先應用分段線性化理論，對電弧爐電極調節系統的模型參考自適應控制演算法進行了研究，推導出全數字化的模型參考自適應律；然後根據推導出的自適應律成功的設計出了的軟體模擬系統，用軟體對電弧爐電極控制進行了模擬研究；最後利用電子電路構造出一套完整的電爐煉鋼電極控制硬體模擬系統，對電爐電極調節進行了實驗室電路模擬研究。A calculation example is used to get some figure. the effect of phase shift and attenuation in temperature fluctuation by thermal mass can be observed in these figures. the cfd simulation of the similar modeling is carried out, the result of the cfd simulation is similar to the calculation example
在前面工作的基礎上，本文作者還利用cfd軟體模擬了和前面模型中相似的情況，即只考慮室內蓄熱體的蓄熱作用，假設外圍護結構是絕熱的，得到的室內空氣溫度變化趨勢與算例所得到的是很相似的。Parametric designing procedure can finish cad parametric design of hydraulic press and engineering drawings of two dimensions based on solid models and the technologies of feature associated and expression of three dimensioned software, and then realize associated design from sketched - design to solid modeling and to engineering drawing of two dimensions
參數化設計過程以三維實體模型為基礎，並應用三維設計軟體特徵、相關、表達式等技術完成了液壓機本體cad參數化設計及相關二維工程圖的繪制與標注，實現了從草圖設計到實體模型再到二維工程圖的全相關設計。The relationship between the resisitivity and the stress was simulated by matlab software. based on the mathematical and physical strength model, the resistivity in different thickness of the composite was attained, and the total resistivity was attained through the integral of thickness, which is basically identical with the tested resistivity
用matlab軟體模擬了應力與電阻率的變化關系式，再結合數學物理力學模型，得到了組元不同厚度處的電阻率值，通過對厚度求積分得到的總電阻率值，與實測電阻率值基本吻合。This paper analyzed the criterion of the safety evacuation, factors affected on safety evacuation, calculating method of evacuation time and the smoke layer falling time, typically introduced the several calculation method that i had know, such as the japan three steps calculation method based on experience ( awareness time, travel time, queue time ), two computer modeling calculation method such as simulex and exodus and a spatial grid computer model of hongkong. and it also analyzed and certificated the application scope and difference between the computer modeling calculation methods and japan method with the practical project. all these are aimed to provided preference for performance - based design method and design of computer program for modeling evacuation of people, and advanced the steps of performance - based fire protection design method in our country
本文對安全疏散的標準、影響安全疏散的因素、疏散時間和影響疏散的煙層下降時間的計算等方面進行分析，重點介紹了作者所掌握的疏散時間的幾種計算方法，日本的三步驟疏散時間經驗公式計算方法（察覺時間、步行時間、排隊等待時間） 、以及兩種計算機疏散計算模型simulex和exodus 、香港的空間網格計算機模型的計算方法等，並結合實際工程來分析驗證疏散計算機軟體模擬和日本經驗公式法之間的不同與適用性，並對疏散計算中的重要參數，人員密度和疏散人數的確定進行介紹，旨在為我國的性能化疏散設計與疏散模擬的計算機軟體的編制提供參考，同時促進我國性能化防火設計的進程。The main task of this paper concentrates on such parts as calibration of measurement sensor, high speed and accuracy image collection and processing, data fusion of different angle of view, visualization of measuring results. to accomplish sensor calibration, a pinhole model of the camera is employed and an equation of a light plane is setup. parameters such as the m array of the pinhole model and the normal vector of the light plane arc acquired through experiment. in image processing, we adopt the template - changing parallel thinning method to improve processing speed and accuracy
主要研究了攝像機針孔模型的建立及測量傳感器的標定；圖像的快速高精度的採集和處理，在圖像處理中採用多幀平均演算法，很好地解決了速度和精度之間的矛盾制約；根據旋動理論建立空間坐標變換數學模型，進而建立其不同視角下的測量數據融合演算法，生成完整的物體三維數據集合；在vc平臺下編寫三維顯示軟體模塊，完成三維測量結果的可視化，實現了三維物體的任意角度的觀察、任意倍數的放大和縮小、任意方向平移及動畫效果。Product design is a complicated thinking activity of creation of human. based on analyzing product design and its process, using a theory and method of aggregating and mapping, models of product design, process of product design, process of conceptual design of product were constructed, a frame of network arithmetic of a process of conceptual design of product was presented, its flow of decomposition and integration was particularly defined ， a good base for modeling and ruling of process of product design was founded. at one time, a useful exploration of development of a computer support implement for process of product design at all life cycle was made
產品設計是一種復雜的人類創造性思維活動.在分析產品設計及其過程的基礎上，利用集合與映射的理論與方法，依此建立了產品設計、產品設計過程、產品概念設計過程的模型，給出了產品概念設計過程的網路演算法框圖，並且詳細定義了後者的分解與綜合的流程，為產品設計過程的模型化、規律化打下了良好的基礎，同時也為產品全生命周期設計過程計算機軟體支持工具的開發作出了有益的探索The author makes a simple curing dealing software by vba language
作者首先使用vba宿主語言編制了一個簡單的固化動力學處理軟體模型。Focus on the problems, three different typical section of mechanism and components was selected to be make computer programs in the research : the joint part with prime motor, the power transmission and the operator. the programs were designed in visual program langue visual c + +. the component ? solid modelings were made using the parametrize feature moulding software pro / e
針對農業機械設計中存在的設計效率低下，設計手段落後，需要反復修改設計的問題，本研究以可視化的程序設計語言visualc + +為開發工具，以參數化的特徵造型軟體pro / e為造型工具，從與原動機聯接部分、動力傳遞部分、工作部件三個不同側面選取農業機械中典型的機構及零部件進行了計算機輔助設計，編制了參數設計的程序，並進行了實體模型的建造，大大提高了這些機構及零部件的設計效率，並為其它零部件的cad提供了參考。A new experimental and training system with modular hardware and software is introduced in this paper based on the research and analysis of the principle, structure and realizing method of microprocessor relay protection and safety automation equipment and the constitutes of cut - up arrangement substation integrated automation at home and abroad whose function includes relay protection experiment, such as current protection, distance protection and so on, and substation integrated automation experiment etc. the structure and function of the experimental and training system are introduced in detail, the principle and function of the hardware section are analyzed, and the method of software designing and programming is concisely set forward. in this paper, a new communication mode between computer and the rs - 485 bus and the can bus by using the computer ' s epp port and an effective method of software ' s remote downloading are brought forward
論文在研究和分析了國內外微機保護和安全自動裝置的原理、結構和實現方法以及分散分散式變電站綜合自動化系統構成的基礎上，開發了一種硬體和軟體模塊化，能實現電流保護、距離保護、故障錄波等多種繼電保護和安全自動裝置功能以及變電站綜合自動化功能的實驗培訓系統，詳細介紹了整個實驗培訓系統的結構和功能，分析了硬體部分的原理和作用，還簡要闡述了整個軟體編制的大體方法，並提出了一種利用計算機的epp口實現上位機與rs - 485總線和can總線通信的新型通信方式，提出了一種利用psd913f2的雙flash的特點進行軟體的遠程在線下載的方法。It consists of two part, the one is hardware : integrating the system of the arc welding robot ' s hardwares and its working principles, separating and extracting the original system ' s control signals, designing the control system openly and its working principles, constructing the structure and principle of the motion card based on dsp, designing the telecontroling teaching box or control panel of touching screen based on usb interface, applying for some software and hardware measures on control system ' s anti - jamming ; the other is software : putting forward the three levels opening software structure model of arc welding, comparing the opening of software structure model between osaca and ours, putting forward the solutions of the pri and communication among the threads of software system ' s modules, using the dll ' s techniques to solve software ' s module design and putting forward the frame codes, bringing forward the path planning software ' s realization by cp + ptp mode, discussing the real time of windows2000 operating system and advancing its solution
具體包括，硬體部分：弧焊機器人硬體整體系統集成及其工作原理，原系統控制信號的分離和提取，控制系統的開放式設計及組成原理，基於dsp的運動控制卡結構和原理，基於usb介面的觸摸屏式遙控示教盒控制面板的設計，系統抗干擾的軟、硬體措施；軟體部分：提出了弧焊機器人的三層開放式軟體結構模型，軟體結構模型與osaca的模型進行開放性比較，給出軟體系統各模塊線程間優先級和通訊的解決方案，使用動態鏈接庫技術實現軟體模塊化設計並給出了框架代碼，給出了cp + ptp方式的軌跡規劃軟體實現過程， windows2000操作系統實時性問題的討論及解決方案。In the paper, theories and functions of the whole system are introduced, the typical theories and algorithms of relay protection employed in the system are lucubrated, the configuration of relay protections is researched, the demonstration constitution schemes are determined, the psd remote program upgrading method based on 80c196kc is provided, the relay protection software is designed based modular structure and in which the technologies of pts data transmission and the lcd multilevel menus which contain chinese characters and graphs are adopted, a configuration software design method is provided for adapting the need of training of different structure of substations, and a set of teaching, experimental and training software which has good teaching effects and has innovation to some extent is designed
本文介紹了整個系統的結構、原理和功能，深入地研究了本系統所用的典型微機保護原理與演算法；研究了保護的配置；確定了變電站綜合自動化系統的示範構成方案；提出了基於80c196kc的psd微機保護遠程程序升級方法；設計了裝置保護軟體，軟體模塊化設計、流程清晰，並採用了pts數據傳送和lcd圖形和多級漢字菜單設計等技術；適應對不同結構的變電站培訓的需要，提出了一種組態軟體設計方法；設計了教學性好、啟迪性強、可靈活組態的教學實驗培訓軟體，有一定的創新性。Taking vc6. 0 and msc6. 0 as the main development kits, this paper completes the modularized software of the three parts of the bus control, the remote terminal, and the monitor terminal, realizes the visible system software. finally, this paper carries on the debugging and testing to the system, analyzes the 1553b bus and the integrated navigation system performance
本文還設計了某型基於1553b總線的機載組合導航系統，完成了總線信息流設計，對其中1553b總線的通信協議進行深入的分析;以visualc + + 6 . 0和msc6 . 0為主要開發工具，完成了總線控制器、遠程終端、監視器終端三部分軟體模塊化設計，實現了可視化系統軟體。Taking the research and development of integrated electronic commerce software gecis as background, this paper brings forward a framework model of form digital signature based on ssl protocol to provide higher security guarantee for ec. the whole task penetrates the developing process based on 3 - layer architecture. it uses architecture methods and technologies such as design pattern ect. moreover, it integrates uml and acme to establish software models
本文以集成電子商務軟體gecis開發項目為背景，構造一個基於ssl協議的表單數字簽名軟體構架模型，為電子商務提供更高安全保障.整個研製工作貫穿基於三層體系結構的構件化軟體開發過程，運用設計模式等軟體體系結構方法和技術，綜合使用統一建模語言uml和體系結構描述語言acme建立軟體模型Based on research and development of integrated supply chain management ( iscm ), we adopt the process of component oriented software development, lay emphasis on the integrated modeling method of agent, petri net and acme, and research on the architecture model and component model of jit ( just in time ) software
在集成供應鏈管理系統開發的背景下，本文以jit軟體的研製為基礎，探討系統開發的過程、方法和工具等軟體工程問題。整個研製工作貫穿基於三層體系結構的構件化軟體開發過程，綜合使用統一建模語言uml 、 agent方法、 petri網方法和體系結構描述語言acme建立軟體模型。Considering uncertainty of crude oils supplying, uncertainty of the capability and yield of equipments, uncertainty of the price of crude oils. the result is compared with the result found by pros vi. 5, verifying the advantage and realizability of fuzzy linear programming. the model can be used to workout a short - term, middle - term, long - term production plan, also it can be modified to optimize stratagem programming with more uncertainties
建立了蘭州煉油廠的生產計劃模糊模型，該模型綜合考慮了原油供給的不確定性、生產裝置的生產負荷和收率分佈的不確定性、原油價格的不確定性，並進行了求解，求解結果和申迪公司圖形建模優化排產軟體模型結果作了對比，證明模糊優化方法編制煉油廠生產計劃的可實現性和優越性。This means that for geronimo to provide a complete package, yet another set of people is going to have to transcribe the public domain rfcs for internet mail into a working software model and then write a clean - room version of the sun javamail api to glue it all together
這也就意味著geronimo要提供一個完整的包，而其他一些人則不得不將不受版權限制的internet郵件rfc轉錄到有效工作的軟體模型內，然後編寫sun javamail api的凈化版本，以將其聚集在一起。The middle and small enterprise applied software system based on the mdg in this paper has gained the “ technological innovation fund for middle and small enterprises ” from the ministry of science and technology of china
基於論文mdg軟體模型設計出的中小企業信息化應用軟體系統得到了國家科技部中小企業技術創新基金的資助。分享友人