軸向位移 的英文怎麼說

中文拼音 [zhóuxiàngwèiyí]
軸向位移 英文
axial di lacement
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 移 : Ⅰ動詞1. （移動） move; remove; shift 2. （改變; 變動） change; alter Ⅱ名詞（姓氏） a surname
  1. The results show that the ultimate bearing capacity can be increased 10 % - 40 % and the lateral displacement and vertical settlement can be decreased 20 % - 50 % and 30 % - 50 % respectively, if the sand foundation is reinforced by geogrid

    由模型試驗測量結果得知，在砂土地基中鋪設塑料土工格柵，可以使承載力提高10 % ~ 40 % 、側向位移量減少20 % ~ 50 % 、地基軸線處豎向沉降減少30 % ~ 50 % 。
  2. Based on the acquaintance of the reason and background of turbine ’ s differential expansion, the thermal characteristics and axial displacement of the steam turbine rotor have been discussed

    本文在介紹和了解汽輪機脹差產生現象的前提下，著手了解研究汽輪機轉子的熱力學特點和軸向位移。
  3. Cross universal coupling is mainly used for rolling machine, mining machine, transportation machine, petroleum, shipping, making paper and other heavy - duty machine, is the most common and highest efficiency gearing, it has larger transmit moment, bigger angle, more flexible rotation, longer life than the old - type plum blossom shaft, smooth piece universal shaft, and gear coupling, it s a new generation product of changing the metallurgy steel rolling equipment reconstructive technology

    利用其結構的特點能使不在同一軸線或軸線折角較大或軸向移動較大的兩軸等角速連續回轉，並可靠地傳遞轉矩和運動。其最大的特點是各向位移補償能力強，結構緊湊，傳動效率高，維修保養方便。廣泛應用於冶金機械，石油機械，造紙機械，工程機械，起重運輸機械以及其他重型機械等等。
  4. By it, the temperature and axial displacement on axes around the blades of the turbine can be measured. the advanced circuits monitor their change. if the temperature and displacement go beyond the normal range, the alert will be sent out, and they can be stopped and repaired " at that time

    渦輪機的工作環境惡劣，為克服環境給測量帶來的困難，採用非接觸式測量方法對渦輪機軸的溫度和渦輪機軸的軸向位移進行測量，採用精確的電路監控溫度和位移的變化，若溫度和位移超出其正常工作范圍，立刻發出警報，停止其工作以進行及時的修理。
  5. Then, this paper edits other computer program to calculate thirty sgrc frame columns, and researches the drift capacity of sgrc frame column, and analysis the turning capacity of frame column " s plastic hinge. then the relational expression of the curvature ductility factor and ratio of hoops of sgrc frame columns is derived. this paper analysis the relation of the curvature ductility factor and the relative drift of sgrc frame columns, and discuss the question of the minimum values of ratios of hoops of sgrc frame column at different axial load ratios

    一11一太原理工大學碩_ i :學位論文使用本文程序另外模擬計算了30榻煤研石混凝土框架，進一步分析了軸壓比和配箍率對煤研石混凝土框架柱曲率延性的影響，編寫程序計算了30根煤研石混凝土框架柱，對煤研石混凝土框架柱的側向變形能力進行了研究，分析了柱塑性鉸的轉動能力，導出了煤研石混凝土框架柱的曲率延性系數與配箍率的關系式，分析了煤研石混凝土框架柱的曲率延性系數與框架柱相對側向位移的關系，討論了煤研石混凝土框架柱在不同軸壓比下最小配箍率的取值問題。
  6. Comparing experimental results with the numerical analytic results using the criterion, it is found that the criterion employs the axial deformations of bracing members as fatigue damage parameters and can be applied to real - time estimation of low - cycle fatigue damage of bracing members under a loading history - dependent random stale

    研究結果表明：本文方法以鋼支撐軸向位移為損傷參量，能實時估算在隨機位移荷載下鋼支撐的低周疲勞累積損傷發展，並與試驗結果吻合較好。
  7. Firstly, with uniaxial symmetrical rectangle cross section, the warping displacement function and tangential displacement function under anti - symmetrical load are supposed. then taking shear deformation into account and with potential principle, the governing differential equation for distortion angle subjected to uniformly distributed distortion load is established

    首先，以單軸對稱矩形截面薄壁桿件為研究對象，假設其在反對稱荷載作用下翹曲位移和切向位移的分佈函數，考慮剪切變形的影響，利用最小勢能原理建立單位均布畸變荷載作用下的畸變角微分方程。
  8. The floor of the high - rise frame structures is very suppleness when the frame structures subjected to the vertical seismic actions, it is impossible to confirm that each member has the same displacement in the same floor, so it is impossible that the summation of axes stiffness of each vertical member represent the global vertical stiffness of the frame structure

    高層建築框架結構在豎向地震作用下，樓板在豎向剛度是很小的，一般不予考慮，認為相對無限柔性，而梁的剛度也是有限的，不可能保證各豎向構件在同一樓層豎向位移相同，因此不能簡單地用各豎向構件軸向剛度之和來代表結構的總豎向剛度。
  9. When the fill factor is less than 1, the concentrated tensile stress appeares near edge of disk surface, while the fill factor reaches up to 1, the surface exhibites compressive stress, and the center is less tensile stress

    當抽運光斑未充滿激光介質時，介質的表面靠近邊緣處會出現大的拉應力集中，並且介質表面的最大軸向位移和最大拉應力隨光斑填充因子增大而增大；而當抽運光充滿介質時，表面是壓應力，較小的拉應力存在於介質內部。
  10. When the pumping area cannot approach the disk had aperture, the concentrated tensile stress appears near the edge of disk hard aperture, while the disk is pumped full aperture the surface exhibits compressive stress, and center is tensile stress which is lesser

    當抽運光斑未充滿激光介質時，介質的表面靠近邊緣處會出現大的拉應力集中，並且介質中最大拉應力和表面的最大軸向位移隨抽運光斑尺寸縮小面增大；而當抽運光充滿介質時，表面是壓應力，較小的拉應力存在於介質內部。
  11. 2 it can made horizontal, acial and angular displacement when being installed. it can t be restricted by the obstruction of pipe and the non - parallel of flange

    2安裝時可產生橫向軸向角向位移，不受管道不通心，法蘭不平行的限制。
  12. Lastly, two axially loaded bored piles in some building site near xichang city was calculated with the method and some useful data and curves including load - settlement curves and distribution of friction resistance etc. are presented. the accordance between the results of calculation and in - situ test verifies the validity of the method developed in the paper

    通過計算，得到相應的荷載?沉降曲線、軸力圖、樁側阻力圖、塑性區、土的豎向位移等值線、樁的滑移過程等結果，並與現場試驗結果吻合較好，說明用本文方法計算分析樁基的工作特性是可行和有效的。
  13. And then make out the nonlinear equations from the mathematics models, the results includes : the contact angler, contact distortion and axial distortion of each rolling element in the bearing

    求解兩種數學模型的非線性方程組，計算出軸承各滾動體在不同工況下內、外圈接觸角，接觸變形和軸承軸向、徑向位移等。
  14. Pinion axial displacement

    小輪軸向位移
  15. Based on the improved codog power plant experiment rig of harbin engineering university, the thesis has set up the displacement measurement system of the middle slippage of the synchronous self shifting ( s. s. s. ) clutch at the first time, and obtained the curve which follows the time variability of the axial displacement when engaging or disengaging and reflects the dynamic change of the s. s. s. clutch for the main engine changeover of codog power plant experiment rig

    本文的研究是建立在對我校原有codog物理模擬實驗臺改進的基礎上進行的，首次建立了三s離合器中間滑移件位移測量系統，獲得了三s離合器中間滑移件在嚙合及脫開過程中的軸向位移隨時間的動態變化曲線，該曲線從一個側面反映了切換過程中三s離合器的動態變化。
  16. 3. as for side web girder, the principle of minimum potential energy has been introduced. by assuming different displacement function, the force and stress formulae for flanges under uniform loading, horizontal axial force, or vertical concentrated force have been derived

    對于邊主肋截面主梁，本文介紹了能量變分法，通過假定板不同的軸向位移函數，推導了懸臂梁在均布荷載、水平軸向力、豎直集中力作用下的微分方程和應力計算公式。
  17. Axial displacement protective device

    軸向位移保護設施
  18. Gear axial displacement

    齒輪軸向位移
  19. When the dimension of the pump is not particular, you can make a model by reverse engineering. iii ) there is a small flat metal piece on the outside of the torque converter ' s shell, called tab. system can get the axial rigid displacement of the equipment by measuring this tab ' s axial movement

    通過本課題研究得到以下結論：一、液力變矩器在加速狀態產生彈性變形引起頸端和柄端的軸向位移和在加壓狀態時產生的彈性變形引起柄端的軸向位移均朝向發動機一側；而在加壓狀態時產生的彈性變形引起頸端的軸向位移方向相反。
  20. The paper researches a kind of system measuring the temperature and displacement of the optical fiber that can monitor and control simultaneously the temperature and displacement of the blades two - way signals of the turbine, and alert when the emergencies happen

    本課題研究的光纖溫度位移測量系統能在惡劣的環境下，同時實時監測渦輪機軸溫及其軸向位移兩路信號，保證其正常工作，並在發生異常情況時，能立刻報警。
分享友人
分享到 Line

分享到臉書