軸向對稱荷載 的英文怎麼說

中文拼音 [zhóuxiàngduìchènhézǎi]
軸向對稱荷載 英文
axially symmetric load
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 對 : Ⅰ動詞1 （回答） answer; reply 2 （對待; 對付） treat; cope with; counter 3 （朝; 向; 面對） be tr...
  • 稱 : 稱動詞（適合; 相當） fit; match; suit
  • 荷 : 荷名詞（蓮） lotus
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  1. The analytic solutions of isotropic elastic layered soil under axisymmetrical, rectangular and strip loads were derived from the basic equations of isotropic elastic mechanics by means of transfer - matrix method. by the result, can easily calculate the additional stress and settlement in layered soil. but these solutions could not properly assess the errors from the elastomer of the bottom layer in foundation soil

    從各向同性彈性力學基本方程出發，利用傳遞矩陣法推導出的多層彈性地基問題在軸對稱荷載、矩形荷載和條形荷載作用下附加應力與沉降的解析解，可以方便地求出層狀地基中的附加應力和沉降，而他們均沒有考慮最下層彈性體計算深度引起的誤差影響。
  2. Author thinks that the direction of the maximum plastic distortion along a constant radius around the crack tip may be considered as the direction of shear - mode fracture ( named pmax - criterion ) and the load when located shear band prongs the ligament in the front of crack tip is regarded as the limited load of shear - mode fracture. ( 3 ) the fad ( fracture assessment diagram ) of titled crack is proposed based on achievements of mesomechanics about i - ii complex ductile fracture of metal, and the titled crack is classified two kinds : void - mode fracture is assessed by fracture assessment curve, and shear - mode fracture by limited load. ( 4 ) using a fe program based on plantle - ressue theory to calculate some mesomechanical parameters, a flange joint structure of a high pressure vessel ( design pressure 31. 4mpa and the thickness of the hemispherical head is half of that of shell. ) is analyzed to determine whether the structure under operation pressure is safe or not, forecast the mode of potential invalidation and argue for the rationality of design of the structure

    試件的整體斷裂為剪切型，但在試件芯部裂尖鈍化區中部出現了韌窩型啟裂並有一定的擴展，說明局部較高的應力三軸度也會使韌窩型機制得以發展，但是不改變試件整體的剪切型斷裂模式；對韌性斷裂的剪切模式的細觀機理做了一定的探討，並且提出了含裂紋構件剪切型斷裂的宏觀判據：認為裂紋前方的集中剪切帶中與裂紋尖端等半徑處最大有效塑性應變出現的方向可以作為裂紋剪切斷裂的方向（可簡稱為_ （ pmax ）準則） ，集中剪切滑移帶貫穿裂紋前方承載韌帶時的載荷可以作為極限載荷；本文運用金屬韌性斷裂細觀力學在一復合型韌性斷裂方面的研究成果，採用失效評定圖的形式，提出了傾斜裂紋的安全性評定方法的基本框架。
  3. Firstly, with uniaxial symmetrical rectangle cross section, the warping displacement function and tangential displacement function under anti - symmetrical load are supposed. then taking shear deformation into account and with potential principle, the governing differential equation for distortion angle subjected to uniformly distributed distortion load is established

    首先，以單軸對稱矩形截面薄壁桿件為研究對象，假設其在反對稱荷載作用下翹曲位移和切向位移的分佈函數，考慮剪切變形的影響，利用最小勢能原理建立單位均布畸變荷載作用下的畸變角微分方程。
  4. In order to overcome the shortages resulted from hypothesis of small deformation in radial symmetry based on thick - wall cylinder, plane stress and uniform pressure about residual stress around cold - expanded hole, a new model was proposed which takes into consideration the effect of split - sleeve, the different states along thick direction of specimen

    摘要針對目前在研究冷擠壓孔邊殘餘應力時，大都採用基於厚壁圓筒的軸對稱小變形、平面應力狀態、孔邊受力為均布載荷等假設所帶來的不足，提出了在三維真實模型狀態下，考慮襯套對孔邊受力的影響、試件在厚度方向上的應力差異等因素。
  5. Axially symmetric load

    軸向對稱載荷
分享友人
分享到 Line

分享到臉書