軸向張力 的英文怎麼說
中文拼音 [zhóuxiàngzhānglì]
軸向張力
英文
axial tensile force-
Cbm sealed condition is bad under neutral plane at axial part where shows tensile stress in syncline structure
向斜中和面以下表現為拉張應力，向斜軸部中和面以下的煤層甲烷封存較差。For strained si pmosfets, the hole mobility is not only determined by the tensity of strain, but also related to the strain types, which are uniaxial compressive strain and biaxial tensile strain. when electric field is high enough, the hole mobility will be deteriorated in pmosfets under biaxial tensile strain, however, in the case of uniaxial compressive strain, the deterioration will never occur
經模型分析發現，應變硅pmosfet空穴遷移率與應力作用方式有如下關系:當橫向電場較高（ > 5 105v / cm ）時，雙軸張應力作用下的應變硅pmosfet的空穴遷移率將發生退化，而單軸壓應力器件則不會受到影響。Promax tension ind corp has long sold and manufactured a variety of custo mized air shafts / air chucks / safety chucks, edge position control systems / epc, powder / air / disk brakes and clutches, ac / dc motor control systems, re - winding / un - winding systems, tension control systems, web inspection systems, automatic color register systems, servo - vector control systems, mmi interface and supervisory control and data acquisition ( scada ) systems and others such as slitting, winding, laminating, extruding, coating, and gravure printing machines, even other auxiliary devices etc. for webs such as paper, films, rubber, textiles and foils
本公司長久以來已經從事製造及銷售有關紙類，薄膜，膠片，紡織品，橡膠等薄片卷材的捲筒物控制糸統周邊設備，諸如氣漲軸，氣漲/安全夾頭，邊緣追蹤器裝置，磁粉/氣壓/碟式煞車器及離合器，交直流轉矩馬達控制系統，收放料車動系統，張力控制裝置，印刷機靜態觀測器，自動套色控制裝置，伺服向量控制系統，人機介面及監控系統及其他有關印刷，貼合，分條，復? ，塗布，上膠，押出，淋膜等產業機械A two component design consisting of appropriate size and length of structural reinforcing rods and dead - end component is required to transfer axial tensile loads and distribute radial compressive forces through the plastic jacket and onto the internal strength members without damaging the fragile plastic jacket or internal optical fibers
螺旋預絞絲結構不僅能有效地降低配合區域內光纜單位應力和避免應力集中，傳遞軸向張力，而且將預絞絲的徑向壓力均勻地分佈在這段較長的配合區域內。The main causes, which have effects on redistribution of internal force in the prestressed frame, including the relative height compressive zone of section, secondary moment and types of load applying are taken into account. the horizontal braces force which results from the tension of the prestressing steel, reduces the pre - compress stress is analyzed
並且探討了各影響因素對框架梁截面延性的影響和由於柱的抗側剛度在預應力鋼筋張拉時約束梁的軸向變形，從而影響預應力在梁中的建立所造成的梁中軸向預壓力的損失。Characteristics of structure : this machine adopts shaft type speed reducer drive which covers less space and can be conveniently repaired. upper supporting roller adopts clamping type fixu which can be conveniently installed. furthermore, it can well regulate deflection of conveying belt ; holdback is set for speed reducer with reliable performance to prevent back - slippign of the glusive belt ; dumper has three types : pneumatically actuated, electric and manual ; course of direction - change roller of the rail has three types : 300, 500 and 800
2結構特點：該機採用軸裝式減速器驅動，佔用空間尺寸小，安裝維修方便上托輥採用夾緊式固定，安裝方便調整輸送帶跑偏能力強，減速器內設逆止器，防止膠帶倒滑的性能可靠卸料器有氣動電動和手動三種驅動型式尾部改向滾筒張緊行程有300 500 800三種，用戶可接輸送距離的1100選取。All the results of axial and radial deformation measurement by digital image processing technique and those by traditional method are compared. the differences of the soil parameters on duncan and chang ' s nonlinear model made by these two methods are analyzed. finally, a compress test results and fem results are provided to show the reasonability and veracity of digital image processing technique to study the soil stress - strain characteristic in triaxial test
（ 2 ）三軸試驗土樣局部變形研究：首先定量比較了三軸試樣沿高度方向不同位置的局部變形（局部徑向變形與局部軸向變形）大小，分析了三軸試樣局部變形的特點和影響因素；然後把三軸試樣數字圖像測量結果與傳統測量結果進行比較，以鄧肯張非線性模型為例進行了模型參數的整理，分析了兩種不問測量方法引起的參數差異：最後用原型壓縮試驗對比有限元數值計算結果，驗證了數字圖像測量方法得到的三軸試驗土體應力應變參數的合理性和準確性。6 ) horizontal braces force of horizon that results from tension. therefore, it reduces pre - compress stress. horizontal braces is stronger, it ' s influence is more important
（ 6 ）橫向約束的存在減弱了張拉在框架梁中形成的軸向力，從而減小在框架梁中預壓應力，橫向約束越強，它的影響就越大。分享友人