軸向生長率 的英文怎麼說

中文拼音 [zhóuxiàngshēngzhǎnglǜ]
軸向生長率 英文
axial growth rates
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 生 : Ⅰ動詞1 （生育; 生殖） give birth to; bear 2 （出生） be born 3 （生長） grow 4 （生存; 活） live;...
  • 長 : 長Ⅰ形容詞1 （年紀較大） older; elder; senior 2 （排行最大） eldest; oldest Ⅱ名詞（領導人） chief;...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 生長 : grow; grow up; ascent; merisis; build up; auxesis; increment; overgrowth; gain; burgeon; bourgeon...
  1. The globalization course was that the preformed texture recrystallized and became the granular equiaxed grain, when the temperature rose and the holding time prolonged, the granular grain melted at some area and at the liquid - solid interface the grain globalized at the role of the curvature overheated

    過程機制為：擠壓形變組織在加熱過程中首先發生再結晶長大變為顆粒狀等軸晶；隨溫度升高和保溫時間延長，等軸晶發生局部熔化，液固界面的曲率過熱使晶粒外形向球狀轉變。
  2. The microstructure morphology, the concentration, the infrared transmittance, and the x - ray rocking curves measured showed that a long single crystal part and axial steadily distributed zone of the concentration existed in the as - grown crystals. the radial concentration distribution has relatively high uniformity

    通過觀察生長態晶體中的微觀組織形貌，並測量晶體軸向和徑向上不同位置處的成分、紅外透過率和x射線回擺曲線，發現晶內有較長的單晶段和軸向成分穩定區。
  3. Growth rates of between 0. 25 and 1. 3μm/min were reported with the c axis of hexagonal zno grown on(0112)-oriented al2o3 lying in the plane of the film。

    據報道，在（0112）取向的Al2O3襯底上生長C軸位於薄膜平面上的六角晶體ZnO的情形中，其生長速率在025mmin和13mmin之間。
  4. The finite element method ( fe '. i ) is adopted to analyze the effects of the numbers of coil turns, current intensity and current frequency upon the rate of joule heat generation in details. the thermo - radiation analytical countermeasures of various types are adopted to carry out the numerical analysis of the effects of the crucible with different shapes and sizes and the blind holes with different depths opened in the tops of crucibles as well as coil positions upon the thermal field distribution whereby solving the main problem of field the thermo - field design of the induction - heating sic crystal growth system. a new combination idea of the thermo - field design obtained by means of the united design of the thermo - insulator and blind holes has been presented

    採用有限元分析方法對線圈匝數、電流強度、電流頻率等對焦耳熱產生速率的影響進行了詳細的分析討論；採用不同的熱輻射分析策略，對不同坩堝形狀、坩堝頂部開設不同深度的盲孔以及線圈的位置等對熱場分佈的影響進行了數值分析，解決了感應加熱碳化硅晶體生長系統熱場設計的主要問題，提出了通過絕熱層與盲孔的聯合設計獲得所需熱場設計的思路，給出了根據軸向溫度梯度的波動對線圈位置實行動態調節以控制熱場的理論依據。
  5. The optimization design of the crank - connect rod mechanism was carried out. collocating the mass reasonably, adjusting the ratio ( ( 1 - f ) / f ) of the long axis to the short axis of the ellipse track, adjusting the direction of long axis to the direction where the internal - combustion engine was not sensitive to the stimulating force. all the above contribute to the max reduction of the vibration

    對單缸內燃機的曲柄滑塊機構進行優化設計，合理的布置加配質量的大小和方向，對軌跡橢圓的長短軸比率（ 1 - f ） / f進行調整，將長軸方向調整到內燃機對激振力不敏感的方向，從而使不平衡力對內燃機所產生的振動最小，以某一具體的單缸內燃機為例進行了計算分析。
分享友人
分享到 Line

分享到臉書