軸向載荷軸承 的英文怎麼說

中文拼音 [zhóuxiàngzǎihézhóuchéng]
軸向載荷軸承 英文
journal for axial load
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 荷 : 荷名詞（蓮） lotus
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 載荷 : load; loading載荷變化 load fluctuation; variation in load; 載荷裝置 load device
  • 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
  1. First of all, build the mathematics models based on the two different work condition : loaded on the axial loading ; loaded on combination loading

    首先，針對實際生產中不同工況，分兩種情況建立數學分析模型:主要承受軸向載荷;承受聯合載荷。
  2. Angle contact ball bearing can be subject to both radial and axial load, it also can be subject to pure axial load, its axial load capacity is depend on the contact angle and increased accordingly. it can be used for high speed and high precision application dueto high limit speed and pre - adjustable rigidity

    角接觸球軸承可同時承受徑向載荷和軸向載荷，也可以承受純軸向載荷，其軸向載荷能力由接觸角決定，並隨接觸角增大而增大，且極限轉速較高，剛性大還可預調，適用於高速、高精度場合。
  3. This research was also supposed to provide a valuable reference for the construction of 500kv eastern hangzhou transformer substation project. to guarantee the rationality of the torsion and bending load application, a set of experimental equipments was transformed from a traditional one by exerting tangential force on the brim of the fan board and conducting broad - billed roller application. in the actually fulfilled experiments on the capabilities of the members under different ratios of torsion and bending, the equipments proved to be well qualified in load applying to large - tonnage members

    試驗中，為保證扭轉及彎矩荷載施加的合理性，在浙江大學工程結構試驗室原有的加載設備的基礎上，分別採用在扇形板邊緣施加切向力和寬軸承滾軸加載的方法，改造並調試出一套可專門用於大噸位構件施加扭轉荷載及組合作用的試驗設備，並利用這套設備進行了離心鋼管混凝土構件在不同彎扭比的組合作用下的試驗研究。
  4. In chapter 3, the subgrid eddy - viscosity model for large eddy simulation is applied to calculate the three dimensions unsteady periodic turbulent flow in yantan francis turbine. the pulsating characteristics of some main physical parameters in flow field are found. the calculated axial water thrust of hydraulic turbine agrees with the model - test value

    第三章採用大渦模擬亞格子渦粘模型，對巖灘混流式水輪機的流場進行三維非定常湍流分析，得到了流場中各物理量的脈動特性，計算出ms的軸向水推力與模型試驗值大小相當；同時論證了對于下機架承重的混流式水輪發電機組可採用其推力軸承負荷作為水電站廠房振動的最大垂直激振荷載。
  5. Four pionts angle contact ball bearing is separable bearing, it can be subject to bi - directional load and have the function of both single row and double rows bearings

    四點接觸球軸承為可分離型軸承，可承受雙向軸向載荷，並有單列和雙列角接觸球軸承的功能。
  6. The basic stress-strain relations are defined with respect to an axially loaded member.

    基本的應力-應變關系是用承受軸向載荷的構件確定的。
  7. Also the influences of the length, diameter, and the ratio of the stiffness of pipe to the stiffness of soil on the bearing mechanisms are discussed. based on these, some useful conclusions are reached

    然後從樁長、樁徑以及樁土剛度比等角度分析了其對單樁承載力、內外側摩阻力、樁端平面應力分佈、軸向荷載傳遞、樁身截面位移等的影響。
  8. Steel - concrete composite columns are the important load - bearing members in steel - concrete composite structures, in general cases, columns are subject to biaxially eccentric load and sometimes lateral load with its cross sections in various kinds of shape

    鋼-砼組合柱是組合結構中的主要承重構件，通常承受雙向偏心軸向荷載、有時還伴有橫向荷載的作用，其截面形式也多種多樣。
  9. In this part, it is also found that the equivalent prismatic column, which is obtained based on the equal elastic critical load as the non - prismatic member, is not actually equivalent to the tapered column in inelastic stability, and the latter has higher load carrying capacity. finally, the behavior of tapered beam - column acted by combined axial load and transverse load has been investigated. a bending - thrust interaction curve is established which is similar to the ones for the design of prismatic members

    三是研究了楔形變截面懸臂構件在大端固定，小端同時承受橫向及軸向荷載共同作用下的強度和彎矩平面內的穩定，同時參考等截面構件的設計公式，得到了用大端截面來表示的軸力p與彎矩m的之間的相關關系。
  10. Yingxian ancient wooden pagoda is a flat - form tall building, which was formed by the superposition of monolayer temples. the height of 67. 31 meters made it encountered two unprecedented puzzles : firstly, with the height increased whopping, wind resisting and aseismatic capability become the main question of the whole structure ; secondly, because of the weight increased unconventionally, members of the lower 1 ~ 3 floors hold overloading perpendicular to grain and they brought large vertical deformation

    相對於一般殿堂結構，高度和自重的成倍增加，使木塔遇到前所未有的兩項難題:其一是因自重增加，使承受上層柱軸向荷載的梁（普拍枋和梁? ）橫紋局壓應力成倍地超過設計強度而產生嚴重的壓縮變形甚至劈裂，導致木塔整體豎向變位。
  11. The characteristics of longitudinal and lateral frame columns are different from general frame columns, due to the high depth - to - width ratio of cross - sections and withstanding large vertical loads. the axial compressive ratio is a very important factor in columns design

    縱、橫向框架柱具有與一般框架柱不同的特點，如柱截面高寬比較大，且承受很大的豎向荷載，其軸壓比設計問題是柱設計的一個非常重要的因素。
  12. In this section the author analyses the rules of the pile ultimate tip resistance and the shaft friction resistance distribution and their exertion of cast - in - place socketed piles instrumented with strainometers in soft muddy rock. the second aspect of the paper is the analysis on the current rock pile vertical bearing capacity in the four standards gb50007 - 2002, tb 10002. 5 - 99, jtj024 - 85 and jgj94 - 94, then the design method with correlated formula of socketed piles in xigeda - mudstone is given. at the end of this paper, based on the research of pressure grouting technique in recent years, and combined with in - site test result, this paper puts forward the design and calculation method to grouted pile in xigeda - mudstone and the principle of choosing grouting parameters, which provid es experiences for applying this technique and further studying

    本論文結合省級科研項目「西攀高速公路昔格達組泥巖層中鉆孔樁提高承載力的研究」 ，所做的研究工作主要在以下三個方面：一是根據8根樁身內埋設量測元件試樁的單樁豎向靜載荷試驗資料，分析了各試驗樁特別是常規沖孔灌注嵌巖樁在昔格達泥巖中的軸向力、側摩阻和樁端阻力的分佈和發揮規律；二是在討論現行規范對嵌巖樁承載力的計算公式的基礎上，探討了在昔格達泥巖層中的沖孔灌注嵌巖樁的側摩阻和端阻的計算方法，並推薦了相應的計算公式；最後，在吸取近年來對灌注樁后注漿技術研究成果的基礎上，結合現場試驗研究結果，分析了該項技術在昔格達巖層中的應用效果，提出了相應的參數選取，從而為壓力灌漿技術的工程應用和進一步研究提供經驗，並為今後在該地層中合理選用樁型以及指導施工提供了依據。
  13. The numerical calculating based on reynolds equation are carried out with the help of computer program built by bearing research institute of xi ' an jiaotong university. the calculating results indicated that three lubricating oil wedge bearing with an end - to - end through gap between the horizontal combine surfaces will not be unsteady factor when the bearing load no change. but the horizontal oil film rigidity will reduce and the working position of axle journal in the bearing will change

    論文利用雷諾方程對# 5軸承的三油楔水平中分軸承進行了數值計算，計算結果表明，當三油楔軸承水平中分面有貫通的縫隙而軸承的載荷不變時，三油楔軸承不會失穩，但會減小水平方向的油膜剛度，改變軸頸在軸瓦中的工作位置。
  14. This type of bearings is separable, which can only carry axial load

    是可分離型軸承，只能承受軸向載荷。
  15. Through teat of relative vibration, center - line and center orbit of the shaft during starting - up and carrying load process, the abrasion mechanism, radial disturbance, loading status, and self - centering capability etc. of the the failured bearing have been analysed, and measures for preventing damage of bearing shoes being put forward

    摘要通過對機組起動及帶負荷過程中軸的相對振動、軸中心線、軸心軌跡的測試，對失效軸承的磨損機理、徑向擾動、承載狀況和軸承自調心能力等進行分析，提出了預防軸瓦損傷的措施。
  16. Compares with the same centripetal ball bearing, has the big radial direction load bearing capacity, mainly is suitable for the cold hot - rolling mill, working roll support rolls and so on cogging mill

    與相同的向心球軸承相比，有較大的徑向負荷承載能力，主要適用於冷熱軋機，開坯機等工作輥支承輥。
  17. The thesis bases on reynolds - equation and researches the working state under the static and dynamic loading situation of the object. under the static loading situation, the steady - state center position of journal is an important parameter, it is discussed, especially under three - lobe bearing, the calculating progress of it has a detailed description, and the progress is practiced by the means of computer programmer

    徑向滑動軸承是其中的重要一類，本論文以徑向滑動軸承為研究對象，以雷諾方程的建立及求解過程為理論基礎，對滑動軸承的處于動態及靜態載荷下的工況情況進行了理論分析。
  18. These bearings are featured by the extremely big axial load carrying capacity and mean while they can also carry cetrain radial load

    軸向載荷能力非常大，在承受軸向載荷的同時還可以徹骨你受干徑向載荷。
  19. Xr series rigid tooth flank helical gear units have the feature of high versatility, good combination and heavy loading capability, along with other merits such as easying to attain various transmission ratio, high efficiency, low vibration and high permissible axis radial load

    Xr系列斜輪硬面減速機是通用性強組合性好承載能力高的一種減速機，它不僅很方便地獲得各種不同的傳動比，而且效率高振動小允許有高的軸伸徑向載荷。
  20. When radial load is applied, the active bearing can surpress the displacement of the shaft, thus obtaining an infinite stiffness

    當有徑向載荷作用時，自主式軸承能抑制軸頸位移並因此使軸承獲得無窮剛度。
分享友人
分享到 Line

分享到臉書